Breezesta PB-1606 User manual

PALM BEACH LOUNGE CHAIR
PB-1606
1 PB-1606 Assembly

A
B
C
D
E
F
ab
c
f
G
d
e
g
Suggested Tools:
Drill, Plastic Mallet
PARTS
PART DESCRIPTION PART NO. QTY
A PB LOUNGE RH FRAME ASSEMBLY SA-00384 1
B PB LOUNGE LH FRAME ASSEMBLY SA-00383 1
C PB SLING SPACER ASSEMBLY SA-00382 1
D FRONT/REAR SLING RAIL ASSEMBLY SA-00391 2
E PB 2-ARM LOUNGE BACK SLAT PRT-00829 3
F FRONT BOTTOM SPREADER PRT-00862 1
G 24"X24" SEAT SLING H-0000-SLG 1
SA-00398 HARDWARE KIT
PART DESCRIPTION PART NO. QTY
A #8 X 1-1/4" TORX SCREW H-0000-S8125 12
b #8 X 1-3/4" TORX SCREW H-0000-S8175 12
c #8 X 2-1/2" TORX SCREW H-0000-S825 6
d 1/4"-10 X 3" LAG SCREW H-0000-S103 2
e T20 & T25 TORX BIT H-0000-CTD 1
f 6-INCH T20 TORX BIT H-0000-T20X6 1
g LEVELING MOUNT H-0000-LM 4
2 PB-1606 Assembly

Please read the entire instruction before beginning
E
A
D
D
F
B
1.
Place Frame Assembly
A
on a flat surface either
as shown or with the slats
on the ground and frame
sticking up in the air. Insert
the 3 Back Slats
E
into the
slots of the frame. This may
require some tapping with
a mallet to set them firmly
into the slot.
The Back Slat tenon is
offset, and is positioned to
the rear of the chair as
seen at right.
2.
If you did not start with the
slats on the floor, carefully rotate
the chair to its back. Align the
top back slot of assembly
B
with
the top back slat. Align the
remaining slats and use a mallet
to start the slat tenons into the
frame, leaving them slightly out.
Insert the front and rear sling rails
(
D
) and the front bottom
spreader (
F
) into their respective
slots. Then complete the process
of seating the back slats into the
frames so all tenons fully seated.
3 PB-1606 Assembly

D
D
F
g
(2) 1-3/4" screws (
b
) on each end
of the rail assemblies and spreader.
bb
3.00 3.00
KEEP FLUSH WITH TOP OF SEAT
a
d
C
c
G
3.
Using the 6" torx bit (hardware
f
), screw
the (12) 1-3/4" screws (
b
) into the bottom
spreader (
F
) and sling rails (
D
). When tight,
the ends of the spreader and rails should
be flush to the two side frame assemblies.
4.
Before flipping the chair to it's feet, install
the (4) leveling mounts
(hardware
g
) by
threading them into the inserts located at
the four corners on the bottom of the chair.
5.
Screw in the back seat slats using (12)
hardware
a
. Start at the top, making sure the
top of the slat is flush to the top of the chair
frame. Then work your way down to the
remaing two slats. For reference, slats are
spaced 3" from the bottom of one to the top of
the next.
While looking at the back, install the remaining
(2) hardware
d
. These will require the larger
end of bit
e
.
6.
Insert sling spacer
C
into the seat frame
as shown at left. Be sure it is pushed against
the back of the seat. Install (6) hardware
c
to hold it in place.
Insert the seat sling (
G
) into the seat frame.
It should drop into the frame with minor
pressure applied to the frame sides.
4 PB-1606 Assembly