Bristan Z2 TBV 1/2 C Wiring diagram

The Flow Valve is timed and will
shut o in 15 ± 5 seconds
Operation
Connect the
hot or cold
water supplies
to the threaded
tails.
3
12
3
4
4
5
Pack Contents
Installation Instructions
& User Guide
Pressure
BAR
1.0
5.0
0.2
4.0
2.0 3.0
60°C
65°C
Specifications
Maximum Static Pressure: 10.0 bar
Maximum Operating Temperature Inlet Connections
Min: 0.5 bar Max: 5.0 bar
Dynamic Water Pressure
Tools You’ll Need
Prior to Installation
Adjustable spannerFlat Screwdriver Pipe cutter
Installation
60-65°C
recommended
Please leave these instructions
with the end user
Product code: Z2 TBV 1/2 C D1
All products manufactured and supplied by Bristan are safe
provided they are installed, used correctly and recieve regular
maintenance in accordance with these instructions.
This product has been tested to the Water Regulations Advisory
Scheme (WRAS) and satisfies the requirements of the Water
Supply (Water Fittings) Regulations 1999 and current bylaws.
For full Installation Requirements & Notes (IRN)
please visit wras.co.uk/directory.
We recommend isolation valves to be fitted to the inlet water
supplies to ensure ease of future maintenance.
Before installing these taps the water supply must be thoroughly
flushed in order to remove any swarf, solder etc.
This product must not be modified in any way as this will
invalidate the guarantee.
1.0
5.0
Pressure
BAR
4.0
2.0 3.0
0
Place the plinths over the holes
in the basin ensuring that the
washers are fitted between the
plinths and the basin.
Fit the taps to
the basin.
x1
x1
x1
x1
Turn on
water
supply
1/2” Male BSP Tap connector
To replace any spare parts
for your tap, why not
scan the QR Code or
visit www.bristan.com
and search for your product.
Spare Parts For Your Tap
Secure the taps to the basin by
using the washer and metal backnut
below the basin.
Push the handle down
to get flow of water
Turn
on water
supply for a
few minutes and
check all joints and
connections for any
leaks.
If the supply pressure is above 3 bar, a
pressure reducing valve must be fitted
If the supply
pressure is above
3 bar, a pressure
reducing valve
must be fitted
Important
The tap will shut o up to
15 ±5 seconds*
*This will vary depending on system pressure
Please fit the basket
filter washer into
the tail in the order
shown
Basket Filter
washer x1
5/Ltr Flow Regulator
Pre-Fitted

Please use this space for any notes you or your installer may have regarding the installation/
plumbing of this product.
At Bristan, we want to make things as easy as possible for our customers. That’s why we oer solid guarantees on
all our products, eective from the date of purchase, to give you peace of mind.
To start your free guarantee simply scan the QR code and register your product. Alternatively visit
www.bristan.com/register to register your product via a computer.
For full guarantee terms and conditions visit www.bristan.com/guarantees.
General Cleaning
Troubleshooting
Notes
Symptom Cause Remedy
No flow or
low flow
rate
Partially closed isolation valve. Open isolation valve.
Instantaneous water heater cycles on
and o as flow rate or pressure is too
low.
Increase water flow rate or
pressure through system.
Head of water is below the
minimum distance required. 5 meters minimum required.
Hot or cold water being drawn o
elsewhere causing pressure changes
or instantaneous boiler temperature
changes.
Do not use other water outlets when using the taps.
Airlock or partial blockage in the supply
pipework.
Flush through pipework to ensure removal of debris
and any airlocks.
Water
dripping
from taps
This is normal for a short time after using
the taps.
This is caused by residual water tension, the build up
of water in the tap body.
If water continues to drip,
possibly due to the ceramic disc valves
Remove valves and clean, refer to 'Maintenance'
section before starting any maintenance.
Taps do not
turn on
Closed isolation valve. Open isolation valve.
Mains water supply turned o. Turn on mains water supply.
3
3
2
1
1
Maintenance - Valve Cleaning
Remove handle
Your fitting has a high quality finish and should be treated with care to preserve the visible
surfaces.
All surfaces will wear if not cleaned correctly, the only safe way to clean your mixer tap is to wipe
with a soft damp cloth. Stains can be removed using washing up liquid. All bath cleaning powders
and liquids will damage the surface of your fitting, even the non-scratch cleaners.
Note: Never use abrasive detergents or disinfectants or those containing alcohol, hydrochloric acid
or phosphoric acid.
Maintenance- Flow Straightener
2
Unscrew
the flow
straightener
and soak in
descaler.
Remove
valve from
the casing
Check that the groove
is clear of any debris
on the inside of valve
casing.
456
Clean the seal
around the
valve and apply
silicon grease
Using a flat screw
driver, remove the
spring and spline.
Pull out valve
body from tap
Rinse and leave to
one side.
Assemble the
valve. apply
grease and
place back into
the tap body.
Replace
handle and
secure with
adjustable
spanner
Prior to doing any
maintenance or
servicing the isolation
valves must be turned
to the
closed/o position.
Important
Rinse
the flow
straightener
Replace
the flow
straightener
into spout