Brita 1200 User manual

BRITA GmbH
Heinrich-Hertz-Straße 4
D-65232 Taunusstein
Tel [phone]
Fax [phone]
http://professional.brita.de
[e-mail]
BRITA Belgium BVBA
Boomsesteenweg 690
B - 2610 Wilrijk
Tel [phone]
Fax [phone]
http://professioneel.brita.be
http://professionnel.brita.be
[email protected]
BRITA
Water Filter Systems Ltd.
9 Granville Way, Bicester
GB - Oxfordshire OX26 4JT
Tel [phone]
Fax [phone]
http://professional.brita.co.uk
[e-mail]
BRITA Benelux BV
Kanaaldijk Noord 109 G
NL - 5642 JA Eindhoven
Tel [phone]
Fax [phone]
http://professioneel.brita.nl
[email protected]
BRITA Spain S.L.
Rambla Cataluña, 18 4º Izq.
E - 08007 Barcelona
Tel [phone]
Fax [phone]
http://professional.brita.net
BRITA AG
Gassmatt 6
CH - 6025 Neudorf/LU
Tel [phone]
Fax [phone]
http://professional.brita.net
[email protected]
BRITA France SARL
16 rue du Bois Chaland
CE 2946 Lisses
F - 91029 Evry Cedex
Tel [phone]
Fax [phone]
http://professional.brita.net
[e-mail]
BRITA ITALIA S.r.l.
Via Bastone, 102
I - 24044 Dalmine (BG)
Tel [phone]
Fax [phone]
http://professional.brita.net
[e-mail]
BRITA Polska Sp. z o.o.
ul. Kolejowa 231
PL - 05-092 Łomianki
Tel [phone]
Fax [phone]
http://professional.brita.net
[e-mail]
BRITA®, AquaQuell™ and AquaVend™ are registered trademarks of BRITA GmbH Germany
Information in the instruction for use subject to change
PN: 536787-001
deutsch
english
français
nederlands
italiano
español
polski
dansk
Handbuch
Handbook
Mode d’emploi
Handboek
Manuale
Manual
Podręcznik
Manual
PURITY 1200 Clean/
PURITY 1200 Clean Extra
Wasserfiltersystem / Water Filter System
Deutsch Seite 2– 11
1 Begriffsübersicht
2 Allgemeine Informationen
3 Betriebs- und Sicherheitshinweise
4 Installation
5 Inbetriebnahme eines Neufilters
6 Austausch der Filterkartusche
7 Filterkapazität
8 Instandhaltung
9 Fehlerbehebung
10 Technische Daten
11 Bestellnummern
English Page 12–21
1 Definition of Terms
2 General Information
3 Operating and Safety Information
4 Installation
5 Commissioning a New Filter
6 Exchanging the Filter Cartridge
7 Filter Capacity
8 Repair
9 Troubleshooting
10 Technical Data
11 Order Numbers
Français Page 22–31
1 Eléments
2 Généralités
3 Consignes d’utilisation et de sécurité
4 Installation
5 Mise en service d’un nouveau filtre
6 Remplacement de la cartouche filtrante
7 Capacité de filtration
8 Entretien
9 Dépannage
10 Caractéristiques techniques
11 Référen c es
Nederlands Pagina 32–41
1 Overzicht van de begrippen
2 Algemene Informatie
3 Gebruiks- en veiligheidsvoorschriften
4 Installatie
5 Inbedrijfstelling van een nieuw filterpatroon
6 Vervangen van de filterpatroon
7 Filtercapaciteit
8 Onderhoud
9 Verhelpen van fouten
10 Technische gegevens
11 Bes telnum m ers
Italiano Pagina 42–51
1 Panoramica delle definizioni
2 Informazioni generali
3 Istruzioni di funzionamento e sicurezza
4 Installazione
5 Messa in funzione di un nuovo filtro
6 Sostituzione della cartuccia filtrante
7 Capacità filtrante
8 Manutenzione
9 Eliminazione guasti
10 Dati tecnici
11 Numeri d‘ordine
Español Página 52–61
1 Términos
2 Información general
3 Indicaciones de funcionamiento y seguridad
4 Instalación
5 Puesta en marcha de un filtro nuevo
6 Cambio del cartucho filtrante
7 Capacidad del filtro
8 Mantenimiento
9 Solución de fallos
10 Datos técnicos
11 Números de pedido
Polski Strona 62–71
1 Przegląd pojęć
2 Informacje ogólne
3 Wskazówki dotyczące użytkowania
i bezpieczeństwa
4 Instalacja
5 Rozruch nowego filtra
6 Wymiana wkładów filtracyjnych
7 Wydajność filtra
8 Konserwacja
9 Usuwanie usterek
10 Dane techniczne
11 Numery zamówień
Dansk Side 72–81
1 Oversigt over begreberne
2 Generelle informationer
3 Drifts- og sikkerhedshenvisninger
4 Installation
5 Ibrugtagning af et nyt filter
6 Udskiftning af filterpatronen
7 Filterkapacitet
8 Vedligeholdelse
9 Udbedring af fejl
10 Tekniske data
11 Bestillingsnumre

BRITA GmbH
Heinrich-Hertz-Straße 4
D-65232 Taunusstein
Tel [phone]
Fax [phone]
http://professional.brita.de
[e-mail]
BRITA Belgium BVBA
Boomsesteenweg 690
B - 2610 Wilrijk
Tel [phone]
Fax [phone]
http://professioneel.brita.be
http://professionnel.brita.be
[email protected]
BRITA
Water Filter Systems Ltd.
9 Granville Way, Bicester
GB - Oxfordshire OX26 4JT
Tel [phone]
Fax [phone]
http://professional.brita.co.uk
[e-mail]
BRITA Benelux BV
Kanaaldijk Noord 109 G
NL - 5642 JA Eindhoven
Tel [phone]
Fax [phone]
http://professioneel.brita.nl
[email protected]
BRITA Spain S.L.
Rambla Cataluña, 18 4º Izq.
E - 08007 Barcelona
Tel [phone]
Fax [phone]
http://professional.brita.net
BRITA AG
Gassmatt 6
CH - 6025 Neudorf/LU
Tel [phone]
Fax [phone]
http://professional.brita.net
[email protected]
BRITA France SARL
16 rue du Bois Chaland
CE 2946 Lisses
F - 91029 Evry Cedex
Tel [phone]
Fax [phone]
http://professional.brita.net
[e-mail]
BRITA ITALIA S.r.l.
Via Bastone, 102
I - 24044 Dalmine (BG)
Tel [phone]
Fax [phone]
http://professional.brita.net
[e-mail]
BRITA Polska Sp. z o.o.
ul. Kolejowa 231
PL - 05-092 Łomianki
Tel [phone]
Fax [phone]
http://professional.brita.net
[e-mail]
BRITA®, AquaQuell™ and AquaVend™ are registered trademarks of BRITA GmbH Germany
Information in the instruction for use subject to change
PN: 536787-001
deutsch
english
français
nederlands
italiano
español
polski
dansk
Handbuch
Handbook
Mode d’emploi
Handboek
Manuale
Manual
Podręcznik
Manual
PURITY 1200 Clean/
PURITY 1200 Clean Extra
Wasserfiltersystem / Water Filter System
Deutsch Seite 2– 11
1 Begriffsübersicht
2 Allgemeine Informationen
3 Betriebs- und Sicherheitshinweise
4 Installation
5 Inbetriebnahme eines Neufilters
6 Austausch der Filterkartusche
7 Filterkapazität
8 Instandhaltung
9 Fehlerbehebung
10 Technische Daten
11 Bestellnummern
English Page 12–21
1 Definition of Terms
2 General Information
3 Operating and Safety Information
4 Installation
5 Commissioning a New Filter
6 Exchanging the Filter Cartridge
7 Filter Capacity
8 Repair
9 Troubleshooting
10 Technical Data
11 Order Numbers
Français Page 22–31
1 Eléments
2 Généralités
3 Consignes d’utilisation et de sécurité
4 Installation
5 Mise en service d’un nouveau filtre
6 Remplacement de la cartouche filtrante
7 Capacité de filtration
8 Entretien
9 Dépannage
10 Caractéristiques techniques
11 Référen c es
Nederlands Pagina 32–41
1 Overzicht van de begrippen
2 Algemene Informatie
3 Gebruiks- en veiligheidsvoorschriften
4 Installatie
5 Inbedrijfstelling van een nieuw filterpatroon
6 Vervangen van de filterpatroon
7 Filtercapaciteit
8 Onderhoud
9 Verhelpen van fouten
10 Technische gegevens
11 Bes telnum m ers
Italiano Pagina 42–51
1 Panoramica delle definizioni
2 Informazioni generali
3 Istruzioni di funzionamento e sicurezza
4 Installazione
5 Messa in funzione di un nuovo filtro
6 Sostituzione della cartuccia filtrante
7 Capacità filtrante
8 Manutenzione
9 Eliminazione guasti
10 Dati tecnici
11 Numeri d‘ordine
Español Página 52–61
1 Términos
2 Información general
3 Indicaciones de funcionamiento y seguridad
4 Instalación
5 Puesta en marcha de un filtro nuevo
6 Cambio del cartucho filtrante
7 Capacidad del filtro
8 Mantenimiento
9 Solución de fallos
10 Datos técnicos
11 Números de pedido
Polski Strona 62–71
1 Przegląd pojęć
2 Informacje ogólne
3 Wskazówki dotyczące użytkowania
i bezpieczeństwa
4 Instalacja
5 Rozruch nowego filtra
6 Wymiana wkładów filtracyjnych
7 Wydajność filtra
8 Konserwacja
9 Usuwanie usterek
10 Dane techniczne
11 Numery zamówień
Dansk Side 72–81
1 Oversigt over begreberne
2 Generelle informationer
3 Drifts- og sikkerhedshenvisninger
4 Installation
5 Ibrugtagning af et nyt filter
6 Udskiftning af filterpatronen
7 Filterkapacitet
8 Vedligeholdelse
9 Udbedring af fejl
10 Tekniske data
11 Bestillingsnumre

9
11
3
4
6
7
5
8
2
1
14
12
10
1315
16
1 Begriffsübersicht
1Druckbehälter
2Filterkartusche
3Druckbehälterdeckel
4Anschlusskopf
5Eingangsschlauch
6Eingangsventil am Eingangsschlauch
7Ausgangsschlauch zum Endgerät
8Verschlusssicherung
9Trittlaschen
10 Auswerfersockel
11 Mantelgriffe
12 Transportschutzkappe
13 Verschnitteinstellschraube
14 Deckelgriff
15 Reduzierstück 1”–3/4”
16 Spülventil mit Spülschlauch
2 Allgemeine Informationen
2.1 Funktion und Anwendungsbereich
Die BRITA Wasserfiltersysteme PURITY 1200 Clean und PURITY 1200 Clean Extra
optimieren Leitungswasser für Gläser-, Besteck- und Geschirrspülmaschinen durch
Teil- bzw. Vollentsalzung.
Durch BRITA PURITY 1200 Clean werden dem Leitungswasser im Durchfluss-
verfahren über einen Ionenaustauscher selektiv Calcium- und Magnesium-Ionen
entzogen. Karbonathärtebedingte Rückstände beim Trocknen des Spülguts sowie
Kalkablagerungen an wichtigen Maschinenteilen werden verhindert. Dadurch verlän-
gert sich die Lebensdauer der Spülmaschinen entscheidend.
Darüber hinaus gewährleistet BRITA PURITY 1200 Clean Extra durch Vollentsalzung
des Leitungswassers die Eliminierung aller im Wasser enthaltenen Salze, wodurch
deren Ablagerung an Gläsern und Bestecken verhindert wird.
2.2 Gewährleistungsbestimmungen
Die Filtersysteme PURITY 1200 Clean und PURITY 1200 Clean Extra unterliegen der
gesetzlichen Gewährleistung von zwei Jahren. Ein Gewährleistungsanspruch kann nur
geltend gemacht werden, wenn alle Hinweise dieser Anleitung befolgt und beachtet
werden.
2.3 Lagerung / Transport
Umgebungsbedingungen bei Lagerung und Transport in den technischen Daten
(Kapitel 10) beachten.
Das Handbuch ist als Teil des Produkts zu verstehen und während der gesamten
Lebensdauer des Filtersystems aufzubewahren und an nachfolgende Besitzer weiter-
zugeben.
2

1 Definition of Terms
1Pressure Vessel
2Filter Cartridge
3Pressure Vessel Lid
4Connector Head
5Inlet Hose
6Inlet Valve on the Inlet Hose
7Outlet Hose to the Terminal Equipment
8Locking
9Kick Loop
10 Ejector Base
11 Mantle Handle
12 Transport Protective Cap
13 Bypass Setting Screw
14 Lid Handle
15 Reducer 1”–3/4”
16 Flush valve with flush hose
2 General Information
2.1 Function and Application
The BRITA PURITY 1200 Clean and PURITY 1200 Clean Extra Water Filter Systems
optimise tap water for dishwashers for glasses, cutlery and crockery by means of
partial or full demineralisation.
In the BRITA PURITY 1200 Clean calcium and magnesium ions are selectively
removed from the drinking water via an ion exchanger using the flow method. This
prevents residues on the dishes during drying due to carbonate hardness and scale
deposits on important machine parts. This means that the dishwashers have a greatly
increased service life.
Furthermore, BRITA PURITY 1200 Clean Extra guarantees elimination of all salts in the
water by means of full demineralisation of the tap water, preventing them from being
deposited on glasses and cutlery.
2.2 Guarantee Provisions
The PURITY 1200 Clean and PURITY 1200 Clean Extra filter systems are subject
to the statutory guarantee of 2 years. A guarantee claim may be asserted only if all
instructions in this Handbook are followed and observed.
2.3 Storage / Transport
Adhere to the ambient conditions in the Technical Data (Chapter10) for storage and
transport.
The handbook should be seen as part of the product and kept for the whole service
life of the filter system and passed on to subsequent owners.
12

2.4 Recycling / Disposal
By disposing of this product and its packaging in the correct manner you are helping to
prevent potential negative impacts on people and the environment that could be caused
by incorrect disposal. Comply with local regulations and bring the units to be disposed of
to a proper recycling facility at the collection points provided.
Exhausted filters are taken back by BRITA at the addresses listed on the back of the
cover.
3 Operating and Safety Information
3.1 Qualified Personnel
Installation and maintenance of the filter system may be carried out only by trained and
authorised personnel.
3.2 Correct Use
The product can only be operated properly and safely if it is installed, used and serviced in
the manner described in this Manual.
3.3 Liability Exclusion
Installation must be carried out in accordance withthe instructions in this Manual. BRITA
shall not be held liable for any damage, including subsequent damage, arising from the
incorrect installation or use of the product.
3.4 Specific Safety Information
Only drinking water within the intake water temperature range listed in Chapter 10
may be used as intake water for the BRITA water filter system. No microbiologically
impaired water or water of unknown microbiological quality may be used without
appropriate sterilisation.
For reasons of flavour, the filtered water is not suitable for the preparation of food and
drinks.
If there is an official requirement of boil tap water, decommission the filter system.
When the requirement to boil water comes to an end, the filter cartridge must be
replaced and the connections cleaned.
BRITA recommends that the filter system not be decommissioned for a long period.
After stagnation times of over 4 weeks, the boiler should be flushed or a pre-rinse
executed. Please also note the maximum usage period of the filter cartridge is 12
months (Chapter 6).
The filter system is not resistant to heavily concentrated cleaning agents (e.g. bleach,
chlorinated solvents, heavy oxidants) and must not come into contact with them.
•
•
•
•
•
13

The filter system must not be opened or dismantled during operation. The filter
cartridge must not be opened.
The pressure vessel and pressure vessel lid of the filter system are designed for a
service life of 10 years (from the date of installation). They must be replaced after
10 years. The hoses must be replaced in rotation after 5 years.
Production date.
Production code sticker filter cartridge and packaging - Example: B715002010
7 Production year, here: 2007
15 Production week, here: calendar week 15
002 Batch No. filter medium, here the second batch filled in terms of quantity
010 Serial number of the filter cartridge, here the tenth cartridge from the second batch
Production code sticker connector head - Example: 7102 XX
7 Production year, here: 2007
10 Production week, here: calendar week 10
2 Production day from Monday (1) to Friday (5), here: Tuesday
xx Internal code
Production date pressure vessel and pressure vessel lid - Example: 0307
03 Production month, here: March
07 Production year, here: 2007
3.5 Technical Safety Assembly Instructions
The terminal device operated with the filter must be free of limescale prior to
installation. !Caution: No water softening system may be operated upstream from
the filter system.
Protect the filter system from sunlight and mechanical damage. Do not assemble
near sources of heat and open flames.
A stop valve must be installed before the filter system intake hose.
If the water pressure is higher than 6 bar, a pressure reducer must be installed before
the filter system.
A non-return valve tested by the DVGW has been factory-installed at the water intake
of the filter head.
No copper pipes and no galvanised or nickel-plated pipes/connectors may be
installed between the water filter and the consumer. The use of Brita hose sets is
recommended here. When choosing the material for parts that come into contact
with water after the BRITA filter system it must be remembered that, due to the
process, decarbonised and/or fully demineralised water contains free carbon dioxide.
All parts must be installed in accordance with the country-specific guidelines on the
installation of drinking water facilities.
•
•
•
•
•
•
•
•
•
•
14

4 Installation
!Caution: Prior to installation read the technical data (Chapter 10) and the operating
and safety information (Chapter 3). After the product has been stored at temperatures
below 0°C, it must be stored (with the original packaging open) at the ambient
temperature of the place of installation for at least 24 hours before use.
4.1 Scope of Delivery
Prior to installation, remove the entire delivery scope from the packaging and check that
everything is there:
1x pressure vessel 1
1x pressure vessel lid 3
1x filter cartridge 2, Note: Blue marking on PURITY 1200 Clean filter cartridge, Red
marking on PURITY 1200 Clean Extra filter cartridge.
1x manual
1x carbonate hardness test or total hardness test
1x sticker for Service Pass, Note: Light blue sticker for PURITY 1200 Clean, red sticker for
PURITY 1200 Clean Extra.
1x reducer 1”–3/4”
1x flush valve with flush hose
If part(s) of the delivery scope are missing, please contact your local BRITA Office (see
back of cover).
4.2 Assembly of the pressure vessel and the pressure vessel lid
Stand on the kick loops 9with both feet.
Lift the pressure vessel 1and turn it clockwise until the mantle handles 11 are over
the kick loops 9.
Remove the transport protective cap 12 from the filter cartridge.
Check the O-ring seal of the filter cartridge 2for correct seat in the
groove, dirt and damage. Note: The cartridge seat has been
lubricated with food-safe lubricant at the factory.
Stand on the kick loops 9with both feet and place the pressure
vessel lid 3on the pressure lid 1. The positioning of the arrow
marking on the lid handle 14 must line up with the “INSERT” groove.
Press the pressure vessel lid 3down and turn clockwise until the
lock engages 8.
•
•
•
•
•
•
15

4.3 Assembly of inlet and outlet hoses
Note: The inlet and outlet hoses are not included in the standard scope of delivery. The
use of BRITA hose sets is recommended (Chapter 11).
Fit inlet hose 5at the inlet of the connector head 4and outlet hose 7at the outlet
of the connector head 4.
Note: Inlet “IN” and outlet “OUT” of the connector head 4are equipped with
O-rings as seals, therefore no additional flat seals may be used here. Make sure that
the O-rings are seated correctly.
!Caution: The max. tightening torque at the 1“ and 3/4“ connections must not exceed
15Nm! Only hose connections with flat seals may be used. Hoses with conical screw
connections damage the connections of the filter head and invalidate any guarantee
claims! Before assembly, note the direction of flow on the upper side of the filter head,
IN = water inlet, OUT = water outlet. Prior to installation, note installation dimensions
and operating position (Chapter 10). If no original hoses are used, the 1“- 3/4“ 15 reducer
supplied must be used to ensure correct sealing of the return valve.
5 Commissioning a New Filter
5.1 Setting the Bypass
The bypass setting screw 13 has been set to 0% at the factory and, if necessary, can
be increased to 10% according to the local water quality or application in question.
If you have any questions about water quality, your supplier or your contact at BRITA
will advise you.
Note: Use Allen key 6mm or 7/32“ to adjust the bypass setting screw 13 .
5.2 Identifying the Filter Capacity
Identify the local carbonate hardness or total hardness using the enclosed carbonate
hardness or total hardness test kit.
Identify the filter capacity using the capacity tables (Chapter 7) taking account of the
carbonate or total hardness identified and the bypass setting (Chapter 5.1).
•
•
•
•
16

5.3 Flushing and Bleeding the Filter Cartridge
Note: A bucket with a minimum capacity of 10L is needed for flushing/bleeding.
Place the bucket under the flush hose and open the flush valve 16 .
Open the inlet valve 6on inlet hose 5while holding the flush hose
in the bucket. Flush with at least 10 litres.
Close the flush valve 16 and empty the bucket.
Check system for any leaks.
Note installation date of the filter system on pressure vessel 1and
next exchange date on the enclosed sticker (PURITY 1200 Clean:
light blue sticker, PURITY 1200 Clean Extra: red sticker) and attach it
to the Service Pass on the pressure vessel 1.
6 Exchanging the Filter Cartridge
The filter cartridge must be replaced after 6–12 months, at the latest 12 months after
commissioning, irrespective of the level of exhaustion of the filter system. If the capacity
of the filter cartridge has been exhausted (Chapter 7), it must be replaced earlier.
!Caution: During the exchange, carefully examine all dismantled parts! Faulty parts
must be exchanged, dirty parts cleaned! Read the operating and safety information
(Chapter 3) prior to replacement. After the product has been stored at temperatures
below 0°C, it must be stored with the original packaging open at the ambient temperature
of the place of installation for at least 24 hours before entering use.
•
•
•
•
•
,
17

6.1 Removing the Filter Cartridge
Switch off the power supply of the terminal equipment (remove plug).
Close the inlet valve 6at the inlet hose 5.
Place the flush hose in a bucket and remove pressure from the filter system by
opening the flush valve 16 . Collect waste water in the 10L bucket.
Note: If the escaping water is more than 1 litre, the inlet value 6is not completely
closed or is blocked with scale.
Stand on the kick loops 9with both feet while opening the pressure
vessel lid 3by pressing the lock 8and turning it anti-clockwise as
far as it will go. The filter cartridge 2is released by pressing on the
mantle handles 11 .
Place the pressure vessel lid 3vertically on the lid handle 14 .
Stand on the kick loops 9with both feet while turning the pressure
vessel 1anti-clockwise by the mantle handles 11 as far as it will go.
Take your feet off the kick loops 9and press the pressure vessel 1
down with both hands on the mantle handles 11 .
Remove used filter cartridge 2from the pressure vessel 1.
Place the used filter cartridge 2in the sink with the connection facing down for
drainage (> 5 min).
Lock the used filter cartridge 2with the transport protection cap 12 of the new filter
cartridge and return in the original packaging to the appropriate BRITA address listed
on the back of the cover.
6.2 Inserting the Filter Cartridge
Check the O-ring seal of the new filter cartridge 2for correct seat in the groove, dirt
and damage. Note: The cartridge seat has been lubricated with food-safe lubricant at
the factory.
Check the connector seat of the filter cartridge O-ring 2in the pres-
sure vessel lid 3for dirt and damage.
Place new filter cartridge 2in the pressure vessel 1.
Stand on the kick loops 9with both feet; lift the pressure vessel 1
whole turning clockwise until the mantle handles 11 are over the kick
loops 9.
Stand on the kick loop 9with both feet and place the pressure vessel
lid 3on the pressure vessel 1. The positioning of the arrow marking
on the lid handle 14 must line up with the “INSERT” groove.
Press the pressure vessel lid 3down and turn clockwise until the
lock engages 8.
Switch on electrical power supply to the terminal device.
Execute the steps described under 5.3 to flush and bleed the new
filter cartridge 2.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
18

7 Filter Capacity
For the precise, continuous control of the degree of filter cartridge exhaustion, it is
recommended to install a control water meter (Art. 236600 together with Art. 315648,
Chapter 11).
Capacity Tables
PURITY 1200 Clean PURITY 1200 Clean Extra
Bypass setting
0 %
Bypass setting
10%
Bypass setting
0 %
Bypass setting
10%
Carbonate
hardness in
°KH
Volume
in litres
Volume
in litres
Total hardness
in °GH
Volume
in litres
Volume
in litres
4 20.000 21.778 4 6.200 6.751
5 20.000 21.778 5 6.200 6.751
617.50019.056 6 5.1675.626
7 15.000 16.333 7 4.429 4.822
8 14.000 15.244 8 3.875 4.219
9 13.000 14.156 9 3.444 3.751
10 12.000 13.067 10 3.100 3.376
11 10.500 11.433 11 2.818 3.069
12 9.250 10.072 12 2.583 2.813
13 8.077 8.795 13 2.385 2.597
14 7.500 8.167 14 2.214 2.411
15 7.000 7.622 15 2.067 2.250
16 6.563 7.146 16 1.938 2.110
17 6.176 6.725 17 1.824 1.989
18 5.833 6.352 18 1.722 1.875
19 5.526 6.018 19 1.632 1.777
20 5.250 5.717 20 1.550 1.688
21 5.000 5.444 21 1.476 1.607
23 4.565 4.971 23 1.348 1.468
25 4.200 4.573 25 1.240 1.350
28 3.750 4.083 28 1.107 1.206
31 3.387 3.688 31 1.000 1.089
35 3.000 3.267 35 886 964
Note: The stated capacities are guide values that may vary by ± 20% depending on the
product volume flow, local water quality and machine type.
8 Repair
Regularly check the filter system for leaks. Regularly check the hoses for kinks. Bent
hoses must be replaced.
The complete filter system must be replaced in rotation after 10 years.
The hoses must be replaced in rotation after 5 years.
!Caution: Prior to exchange read the technical data (Chapter 10) and the operating and
safety information (Chapter 3).
19

Regularly clean the outside of the filter system with a soft, damp cloth.
!Caution: Do not use any substances incompatible with the material (Chapter 3.4) or
astringent, abrasive cleaning agents.
9 Troubleshooting
9.1 No water flow
Cause: Water intake closed.
Troubleshooting: Open water intake on the upstream stop valve or inlet valve 6on inlet
hose 5.
!Caution: The following faults may be remedied only by trained and authorised
personnel.
9.2 No or low water flow in spite of open water intake
Cause: Mains pressure too low.
Troubleshooting: Check mains pressure.
If the fault continues to occur in spite of adequate mains pressure,
check the filter system and filter cartridge and change if necessary.
!Caution: Prior to exchange read the technical data (Chapter 10) and
the operating and safety information (Chapter 3).
9.3 Leaking screw connections
Cause: Screwed connections not fitted correctly.
Troubleshooting: Check mains pressure. Check all screwed connections and mount
according to Chapter 4.
If the fault continues, exchange filter system.
!Caution: Prior to exchange read the technical data (Chapter 10) and
the operating and safety information (Chapter 3).
9.4 Leak continues after filter has been replaced
Cause: O-ring on filter cartridge not sitting correctly.
Troubleshooting: Check correct seat of the O-ring (Chapter 6.2).
!Caution: Prior to dismantling read the data (Chapter 10) and the
operating and safety information (Chapter 3).
20

10 Technical Data
Water filter systems
PURITY 1200 Clean with filter cartridge
PURITY 1200 Clean Extra with filter cartridge
Operating pressure 2bar to max. 6bar
Water intake temperature +4°C to +60°C
Ambient temperature for storage/transport –20°C to +60°C
Nominal flow 300 L/h
Pressure loss at nominal flow 0,45 bar
Weight (dry/wet) 18 kg / 24 kg
Dimensions complete system
(Width/Depth/Height)
288 mm / 255 mm / 550 mm
Installed dimensions The bending radii of the inlet and outlet hose 2m, DN13,
3/4“ 3/4“ are 130mm and, depending on the installation
orientation and operating space, must be considered in
addition to the dimensions of the complete system.
Operating position Horizontal or vertical
Inlet connection 1x G1”
Outlet connection 1x G3/4”
11 Order Numbers
BRITA PURITY 1200 Clean / PURITY 1200 Clean Extra
Article Article Number
PURITY 1200 Clean (complete system with filter cartridge) 292083
PURITY 1200 Clean Extra (complete system with filter cartridge) 292084
PURITY 1200 Clean replacement cartridge 315645
PURITY 1200 Clean Extra replacement cartridge 315650
Accessories
Article Article Number
PURITY inlet hose set (2m DN 13, 3⁄4”-3/4”, valve) 315646
PURITY outlet hose set (2m DN 13, 3⁄4”-3/4”, arc) 315647
Control water meter 236600
Assembly set for control water meter 315648
Universal wall mount (for wall mounting) 234000
21

BRITA GmbH
Heinrich-Hertz-Straße 4
D-65232 Taunusstein
Tel [phone]
Fax [phone]
http://professional.brita.de
[e-mail]
BRITA Belgium BVBA
Boomsesteenweg 690
B - 2610 Wilrijk
Tel [phone]
Fax [phone]
http://professioneel.brita.be
http://professionnel.brita.be
[email protected]
BRITA
Water Filter Systems Ltd.
9 Granville Way, Bicester
GB - Oxfordshire OX26 4JT
Tel [phone]
Fax [phone]
http://professional.brita.co.uk
[e-mail]
BRITA Benelux BV
Kanaaldijk Noord 109 G
NL - 5642 JA Eindhoven
Tel [phone]
Fax [phone]
http://professioneel.brita.nl
[email protected]
BRITA Spain S.L.
Rambla Cataluña, 18 4º Izq.
E - 08007 Barcelona
Tel [phone]
Fax [phone]
http://professional.brita.net
BRITA AG
Gassmatt 6
CH - 6025 Neudorf/LU
Tel [phone]
Fax [phone]
http://professional.brita.net
[email protected]
BRITA France SARL
16 rue du Bois Chaland
CE 2946 Lisses
F - 91029 Evry Cedex
Tel [phone]
Fax [phone]
http://professional.brita.net
[e-mail]
BRITA ITALIA S.r.l.
Via Bastone, 102
I - 24044 Dalmine (BG)
Tel [phone]
Fax [phone]
http://professional.brita.net
[e-mail]
BRITA Polska Sp. z o.o.
ul. Kolejowa 231
PL - 05-092 Łomianki
Tel [phone]
Fax [phone]
http://professional.brita.net
[e-mail]
BRITA®, AquaQuell™ and AquaVend™ are registered trademarks of BRITA GmbH Germany
Information in the instruction for use subject to change
PN: 536787-001
deutsch
english
français
nederlands
italiano
español
polski
dansk
Handbuch
Handbook
Mode d’emploi
Handboek
Manuale
Manual
Podręcznik
Manual
PURITY 1200 Clean/
PURITY 1200 Clean Extra
Wasserfiltersystem / Water Filter System
Deutsch Seite 2– 11
1 Begriffsübersicht
2 Allgemeine Informationen
3 Betriebs- und Sicherheitshinweise
4 Installation
5 Inbetriebnahme eines Neufilters
6 Austausch der Filterkartusche
7 Filterkapazität
8 Instandhaltung
9 Fehlerbehebung
10 Technische Daten
11 Bestellnummern
English Page 12–21
1 Definition of Terms
2 General Information
3 Operating and Safety Information
4 Installation
5 Commissioning a New Filter
6 Exchanging the Filter Cartridge
7 Filter Capacity
8 Repair
9 Troubleshooting
10 Technical Data
11 Order Numbers
Français Page 22–31
1 Eléments
2 Généralités
3 Consignes d’utilisation et de sécurité
4 Installation
5 Mise en service d’un nouveau filtre
6 Remplacement de la cartouche filtrante
7 Capacité de filtration
8 Entretien
9 Dépannage
10 Caractéristiques techniques
11 Référen c es
Nederlands Pagina 32–41
1 Overzicht van de begrippen
2 Algemene Informatie
3 Gebruiks- en veiligheidsvoorschriften
4 Installatie
5 Inbedrijfstelling van een nieuw filterpatroon
6 Vervangen van de filterpatroon
7 Filtercapaciteit
8 Onderhoud
9 Verhelpen van fouten
10 Technische gegevens
11 Bes telnum m ers
Italiano Pagina 42–51
1 Panoramica delle definizioni
2 Informazioni generali
3 Istruzioni di funzionamento e sicurezza
4 Installazione
5 Messa in funzione di un nuovo filtro
6 Sostituzione della cartuccia filtrante
7 Capacità filtrante
8 Manutenzione
9 Eliminazione guasti
10 Dati tecnici
11 Numeri d‘ordine
Español Página 52–61
1 Términos
2 Información general
3 Indicaciones de funcionamiento y seguridad
4 Instalación
5 Puesta en marcha de un filtro nuevo
6 Cambio del cartucho filtrante
7 Capacidad del filtro
8 Mantenimiento
9 Solución de fallos
10 Datos técnicos
11 Números de pedido
Polski Strona 62–71
1 Przegląd pojęć
2 Informacje ogólne
3 Wskazówki dotyczące użytkowania
i bezpieczeństwa
4 Instalacja
5 Rozruch nowego filtra
6 Wymiana wkładów filtracyjnych
7 Wydajność filtra
8 Konserwacja
9 Usuwanie usterek
10 Dane techniczne
11 Numery zamówień
Dansk Side 72–81
1 Oversigt over begreberne
2 Generelle informationer
3 Drifts- og sikkerhedshenvisninger
4 Installation
5 Ibrugtagning af et nyt filter
6 Udskiftning af filterpatronen
7 Filterkapacitet
8 Vedligeholdelse
9 Udbedring af fejl
10 Tekniske data
11 Bestillingsnumre