Broseley YORK User manual

© 2007-2008 Broseley Fires Ltd
InstallationandOperationManual
YorkElectricStoves
Revision: GB07a

© 2007-2008 Broseley Fires Ltd
Thank you for purchasing a decorative effect Electric Stove, this appliance
has been made with great care. Here are some instructions for setting up
your stove, cleaning and maintenance. Please pay careful attention to
these instructions as they will help you to keep your stove in good
condition for many years to come. If you should experience any parts or
service problems, please contact your retailer.
WARNING
• This appliance must be earthed.
• Do not cover or hang clothes, towels etc., over or near the heater as this could
cause over heating and possible damage.
• The guard used on this appliance satisfies the heating appliance fireguards and
safety regulations 1991.
• The guard is to prevent the risk of fire or injury from burns and should not be
permanently removed as it would not give full protection for the young and infirm.
• This appliance must not be positioned below a socket.
• Do not use this heater with a thermal control, programme controller, timer or any
other device which switches the heater on automatically, since a fire risk exists if
the heater is covered or displaced.
• Do not use this heater in the immediate surroundings of a bath, shower or
swimming pool.
ELECTRICALCONNECTIONS– United Kingdom only
This appliance must only be connected to 230/240 Volts a.c. 50 Hz supply.
This appliance is fitted with a moulded plug. A 13 amp fuse is fitted.
Before connecting the fire, check that the supply voltage is the same as that stated on
the fire. This appliance must only be used on AC supply. Fuse rating 13 amps.
This appliance must be positioned so that the plug is accessible. If the supply cord of the
appliance is damaged it must be replaced by a “competent person”.
Warning this appliance must be earthed
Green and Yellow: EARTH
Blue: NEUTRAL
Brown: LIVE
As the colours in the mains lead of this appliance may not correspond with the coloured
markings identifying the terminals in your plug, proceed as follows:
The wire that is coloured green and yellow must be connected to the terminal in the plug
which is marked with the letter E or by the earth symbol or coloured green and yellow.
The wire that is coloured blue must be connected to the terminal that is marked with a
letter N, or coloured black.
The wire that is coloured brown must be connected to the terminal that is marked with
the letter L, or coloured red.
If the terminals of the plug are unmarked, consult a qualified electrician. Two-pin plugs
must not be used.

© 2007-2008 Broseley Fires Ltd
POSITIONINGYOURSTOVE
This appliance should be positioned on a firm level surface. If the customer is positioning
the stove in a fire surround the customer should establish the suitability of the surround
for use with an electric stove.
3
SETTINGUPYOURELECTRICSTOVE
The stove will be received in two separate boxes. The first contains the cast iron stove
body and the second the Flame effect and Heating Unit (Both units are fully assembled)
Carefully remove all the packaging from both boxes and remove any protective
packaging from inside.
Box 1
1 x Cast Iron Electric Stove main body.
1 x Cast Iron Stove Lid.
1 x Set of Four Legs.
1 x Set of Four Bolts and Washers (for fixing the legs to the stove) already screwed into
the base of the stove body.
Box 2
1 x Flame Effect Unit complete with Fan Heater attached.
1 x This instruction booklet.
1 x Bag of real coal
Proceed as follows:
Turn the main stove body onto its back and attach the four legs by means of the bolts
and washers supplied which are already in the base plate of the stove. Tighten with a
spanner. Check that the bolts move freely and do not force or over-tighten as the bolt
may sheer off. Stand the stove upright on its legs.
Before installing the Flame Effect and Heater unit, please ensure that hands
are clean so that no grease or dirt is transferred to the flame effect screen.
Pass the plug and lead through the large rectangular cut out in the base plate of the
stove body.
Position the flame effect and heater unit into the back of the stove body. The fan heater
part is positioned out of the bottom of the stove base plate. (Insert the flame effect and
heater unit via the top of the stove body. The outside edges of the flame effect and
heater unit slide into the channels in the back of each side plate. Slide the unit down
from the top until the top of the back is level with the top of the side plates). DO NOT
FORCE THE FLAME EFFECT AND HEATER UNIT INTO POSITION as it may suddenly
drop if unsupported. The door insert is secured from the inside with screws. This can
easily be changed for another design if required. To do this, it is first necessary to
remove the Perspex screen. To open the main door the brass handle unscrews. There is
a hexagonal key (supplied) locking screw securing the handle which may have to be
loosened prior to removing the handle. The screen on the door is covered with an
obscured protective layer which needs to be removed from the surface prior to final
installation.

© 2007-2008 Broseley Fires Ltd
Check the following before you start setting up your stove.
4
Ensure that the electrical lead and plug are not trapped between the flame effect unit
and the base plate of the stove.
Place the real coals in a decorative position along the coal effect.
Place the stove in the position where you wish to use it taking note of the section
‘POSITIONING YOUR STOVE’ and place the stove lid onto the top of the stove body
ensuring that it fits snugly into place.
YOUR STOVE IS NOW READY FOR USE.
OPERATINGTHESTOVE
Turn the lower handle and open the ash door to reveal the control panel.
The bank of switches at the right hand side of the fan heater, control the flame effect and
heat settings. The numbered control on the left side sets the thermostat. To use the
flame effect without heat, depress the first switch on the left. The other switches control
the heat output, the more that are depressed the higher the heat output. The thermostat
control can be set to the desired level on all heat settings. The stove will automatically
switch on and off to maintain the set temperature.
THERMOSTAT
The thermostat enables the room temperature to be controlled around a pre-set level
and can be used when any of the heat switches are on. To set the thermostat, first turn
on the heat switches and set the control at position 9. Heat the room to the desired
temperature. When this temperature has been reached, reduce the setting by turning the
control anti-clockwise towards a lower figure until you hear the thermostat click off. The
fan heater will stop. When the room temperature drops the thermostat will turn the full
heat from the fire back on again. At very low temperature (approximately 6 degrees C)
the thermostat will not turn the fire off. The thermostat can be adjusted at any time to
increase or decrease the desired temperature. The set level will be maintained until
adjusted or switched off.
Please ensure that nothing is left in front of the fan when it is switched on and that
the air intake remains clear of obstruction at all times.
SAFETYCUT-OUT
The heating element is fitted with a safety cut-out which will switch off the fire if it
overheats.
Should this occur, remove the plug from the socket and allow the fire to cool down. Then
check that there are no objects blocking the air inlets to the fan at the side and rear and
that there is no obstruction of the fan outlet at the front. When the fire has cooled
sufficiently the cut-out will re-set automatically. The fire must be switched off at the plug
for the cut-out to reset. If the fault persists seek professional advice.
CLEANINGANDMAINTENANCE
First of all, disconnect the plug from the wall
Flame effect
The flame effect is factory set and not adjustable. If however during transportation or
installation the flames have become displaced they can easily be repositioned once the
fuel effect and screen have been removed.

© 2007-2008 Broseley Fires Ltd
Screen cleaning
The nature of the screen material can cause static, it is important that any cleaning
preparation used on the front screen (in front of the flame effect) contains anti-static
properties. Do not use abrasive or solvent based cleaners on any part of this appliance.
Should the cast iron outer shell become tarnished or marked it can be re-sprayed, using
touch up spray paint available from your local stockist.
Changing Bulbs
Undo the main stove door. Remove the screw from the log effect. Lift the fuel bed clear
from the fire to give access to the two 40-watt 230/240 volt SES clear candle lamps.
When changing bulbs make sure they are screwed in tight and check that they work
prior to re-assembly. Replace the damaged bulbs and replace the fuel bed accordingly.
You may prefer to remove the lid of the stove to gain access to the fuel bed rather than
open the main door. Periodically check the fan air intake for dust build-up.
6 Guarantee
Your decorative Electric Stove, when installed and operated in accordance with these
instructions should provide many years of safe and efficient operation.
We thank you for purchasing this product and trust it will provide excellent service.
The body of this appliance carries a one (1) year guarantee.
The electrical components are guaranteed against faulty parts or workmanship for 12
months from the date of purchase. Please retain your receipt as proof of purchase.
Elements and bulbs are considered to be consumable items.
The rights given in this guarantee are limited to the U.K. mainland and are in addition to
any to which you may have under statutory entitlement.
For claims and service under guarantee please contact your retailer / supplier.
Please retain your purchase receipt. We will need to see this in the event of a claim
under warranty.
THIS STOVE HAS BEEN SUPPLIED BY:
Address
Telephone.
Date Purchased
Broseley Fires Ltd.
1444 Fax: [phone] www.broseleyfires.com
BROSELEY FIRES LTD.,
KNIGHTS WAY, BATTLEFIELD ENTERPRISE PARK, SHREWSBURY. SY1 3AB.
[phone] FAX [phone]