Broyhill BORDO Avon Lake 12101 User manual

Page 1 of 8
*Please read the assembly instructions prior to assembling this product.
*Assembly by two adults is recommended.
*Assemble on soft surfaces to prevent damage to product finish.
*Keep children away during assembly. This item contains small parts which can be
swallowed by children.
*Do not discard any of packaging until you have checked that you have all the parts and
hardware.
*Do not use power tools.
*Remove all packaging material, make sure all parts are present before assembly.
*Should this product become damaged, and/or components are broken or missing, DO
NOT USE.
*Do not sit or stand on the product, death or serious injury may occur.
*Children should always be under direct adult supervision while using the product.
*Wipe with a soft, dry cloth. To protect finish, avoid the use of water, chemicals and
household cleaners.
*Do not place objects which are more than 80 degrees Fahrenheit on the surface.
*To prolong life of the product, keep the product away from direct sunlight.
*Determine you have adequate space for assembly.
GENERAL BEST PRACTICES FOR ASSEMBLY:
WARNINGS:
MAINTENANCE:
*Retain the assembly instructions for further reference.
*The manufacturer will not accept responsibility for unauthorized repairs or modifications
to this product.

Page 2 of 8
Before assembly, please remove all parts from the carton, verifying that you have the
correct quantities, and read all the instructions.
You may need an assistant to finish these steps easily!
table and a assembly surfaces.
Please DO NOT fully tighten all bolts until frame assembly is complete.
Please assemble on a soft flat surface such as carpet or a towel to avoid scratching
HELPFUL HINTS

Page 3 of 8
PARTS LIST
HARDWARE LIST
Allen Bolt
1/4" x 1/2"
Allen Bolt
1/4" x 1-1/2"
Allen Key
Ø4mm x 2-1/4"
1
3 4
2
x8
x1
Leveler
Ø3/4" x 3/5"
x4x6
A
D
B
x1
Lower Support Frame
x1
Table Top
Back Side Frame
x1
C
x2
Vertical Support Bars

TOP
BOTTOM
A
B
Attach Lower Support Frame (B) to
the Back Side Frame (A) by using
Allen Bolt (1) with an Allen Key (4)
as shown in the diagram.
IMPORTANT
Do not fully tighten the bolts in this
Step until the completion of Step 3.
Assembled View:
Hardware needed:
1
x4
4
x1
STEP 1
Page 4 of 8
1
1
4

TOP
BOTTOM
A
B
Assembled View:
C
Attach Vertical Support Bar (C) to
Lower Support Frame (B) by using
Allen Bolt (2) with an Allen Key (4)
as shown in the diagram.
IMPORTANT
Do not fully tighten the bolts in this
Step until the completion of Step 3.
STEP 2
Page 5 of 8
Hardware needed:
2
x2
4
x1
24

TOP
BOTTOM
D
A
B
Place the Table Top (D) upside down
on a padded, non-marring surface.
Attach the assembled base frame (from
step 2) to the Table Top (D) by using
Allen Bolt (1), Allen Bolt (2) with an Allen
Key (4) as shown in the diagram.
Fully tighten all Allen Bolts from Steps 1
through 3 at this time.
Assembled View:
C
4
x1
1
x2
2
x2
STEP 3
Page 6 of 8
Hardware needed:
2
4
1
4

Insert Leveler (3) into the Lower
Support Frame (B) and fully tighten.
Return the table to the upright position.
The levelers can be adjusted as
needed so the Table is level and
stable. All adjusters should be in full
contact with the floor.
TOP
BOTTOM
D
AB
Assembled View:
C
STEP 4
Page 7 of 8
3
x8
Hardware needed:
3

Assembly is now complete.
PRINTED IN VIETNAM
STEP 5
Page 8 of 8