Bullet Electric scooter User manual

Colours may vary

Electric Scooter

User Manual

[Revision 5.0 January 2019]

READ THIS MANUAL CAREFULLY BEFORE USE – FAILURE TO DO SO MAY RESULT IN INJURY, PROPERTY

DAMAGE AND MAY VOID WARRANTY. • KEEP THIS MANUAL FOR FUTURE REFERENCE. • Products covered by

this manual may vary in appearance, assembly, inclusions, specifications, description and packaging.

Electric Scooter

Safety

Safety messages are designed to alert you to possible dangers or hazards that could cause death,

injury or equipment or property damage if not understood or followed. Safety messages have the

following symbols:

You WILL be KILLED or

SERIOUSLY INJURED if you

do not follow instructions.

You CAN be KILLED or

SERIOUSLY INJURED if you

do not follow instructions.

You CAN be INJURED if you

do not follow instructions or

equipment damage may occur.

It is vital that you read and understand

this user manual before using the product,

including safety warnings, and any

assembly and operating instructions.

Keep the manual for future reference.

Safety precautions and recommendations

detailed here must be fully understood

and followed to reduce the risk of injury,

fire, explosion, electrical hazard, and/or

property damage.

Safety information presented here is

generic in nature – some advice may not

be applicable to every product. The term

"equipment" refers to the product, be it

electrical mains powered, battery powered

or combustion engine powered.

•Before Use - If you are not familiar with

the safe operation/handling of the

equipment, or are in any way unsure of

any aspect of suitability or correct use

for your application, you should

complete training conducted by a

person or organization qualified in safe

use and operation of this equipment,

including fuel/electrical handling and

safety.

•Do NOT operate the equipment in

flammable or explosive environments,

such as in the presence of flammable

liquids, gases or dust. The equipment

may create sparks or heat that may

ignite flammable substances.

•Keep clear of moving parts.

•Equipment may be a potential source of

electric shock or injury if misused.

•Do NOT operate the equipment if it is

damaged, malfunctioning or is in an

excessively worn state.

•Do NOT allow others to use the

equipment unless they have read this

manual and are adequately trained.

•Keep packaging away from children -

risk of suffocation! Operators must use

the equipment correctly. When using

the equipment, consider conditions and

pay due care to persons and property.

General Work Area Safety

•Work areas should be clean and well it.

•Do not operate the equipment if

bystanders, animals etc are within

operating range of the equipment or the

general work area.

•If devices are provided for connecting

dust extraction / collection facilities,

ensure these are connected and used

properly. Dust collection can reduce

dust-related hazards.

General Personal Safety

•Wear appropriate protective equipment

when operating, servicing, or when in

the operating area of the equipment to

help protect from eye and ear injury,

poisoning, burns, cutting and crush

injuries. Protective equipment such as

safety goggles, respirators, non-slip

safety footwear, hard hat, hearing

protection etc should be used for

appropriate equipment / conditions.

Other people nearby should also wear

appropriate personal protective

equipment. Do not wear loose clothing

or jewellery, which can be caught in

moving parts. Keep hair and clothing

away from the equipment.

•Stay alert and use common sense

when operating the equipment. Do not

over-reach. Always maintain secure

footing and balance.

•Do not use the equipment if tired or

under the influence of drugs, alcohol or

medication.

•This equipment is not intended for use

by persons with reduced physical,

sensory or mental capabilities.

General Fuel Safety

•Petrol/fuel/gasoline is extremely

flammable – keep clear of naked

flames or other ignition sources.

•Do not spill fuel. If you spill fuel, wipe it

off the equipment immediately – if fuel

gets on your clothing, change clothing.

•Do NOT smoke near fuel or when

refuelling.

•Always shut off the engine before

refuelling.

•Do NOT refuel a hot engine.

•Open the fuel cap carefully to allow any

pressure build-up in the tank to release

slowly.

•Always refuel in well ventilated areas.

•Always check for fuel leakage. If fuel

leakage is found, do not start or run the

engine until all leaks are fixed.

General Carbon-Monoxide Safety

•Using a combustion engine indoors

CAN KILL IN MINUTES. Engine

exhaust contains carbon-monoxide – a

poison you cannot smell or see.

•Use combustion engines OUTSIDE

only, and far away from windows, doors

and vents.

General Equipment Use and Care

•The equipment is designed for

domestic use only.

•Handle the equipment safely and

carefully.

•Before use, inspect the equipment for

misalignment or binding of moving

parts, loose components, damage or

any other condition that may affect its

operation. If damaged, have the

equipment repaired by an authorised

service centre or technician before use.

•Prevent unintentional starting of the

equipment - ensure equipment and

power switches are in the OFF position

before connecting or moving

equipment. Do not carry equipment

with hands or fingers touching any

controls. Remove any tools or other

items that are not a part of the

equipment from it before starting or

switching on.

•Do not force the equipment. Use the

correct equipment for your application.

Equipment will perform better and be

safer when used within its design and

usage parameters.

•Use the equipment and accessories

etc. in accordance with these

instructions, considering working

conditions and the work to be

performed. Using the equipment for

operations different from those

intended could result in hazardous

situations.

•Always keep equipment components

(engines, hoses, handles, controls,

frames, housings, guards etc) and

accessories (cutting tools, nozzles, bits

etc) properly maintained. Keep the

equipment clean and, where applicable,

properly lubricated.

•Store the equipment out of reach of

children or untrained persons. To avoid

burns or fire hazards, let the equipment

cool completely before transporting or

storing. Never place or store the

equipment near flammable materials,

combustible gases or liquids etc.

•The equipment is not weather-proof,

and should not be stored in direct

sunlight, at high ambient temperatures

or locations that are damp or humid.

•Do not clean equipment with solvents,

flammable liquids or harsh abrasives.

•For specific equipment safety use and

care, see Equipment Safety.

Electric Scooter

General Electrical Safety

•Inspect electrical equipment, extension

cords, power bars, and electrical fittings

for damage or wear before each use.

Repair or replace damaged equipment

immediately.

•Ensure all power sources conform to

equipment voltage requirements and

are disconnected before connecting or

disconnecting equipment.

•When wiring electrically powered

equipment, follow all electrical and

safety codes.

•Wherever possible, use a residual

current device (RCD).

•High voltage / high current power lines

may be present. Use extreme caution

to avoid contact or interference with

power lines. Electrical shock can be

fatal.

General Electrical Safety

•Electrically grounded equipment must

have an approved cord and plug and

be connected to a grounded electrical

outlet.

•Do NOT bypass the ON/OFF switch

and operate equipment by connecting

and disconnecting the electrical cord.

•Do NOT use equipment that has

exposed wiring, damaged switches,

covers or guards.

•Do NOT use electrical equipment in wet

conditions or in damp locations.

•Do NOT use electrical cords to lift,

move or carry equipment.

•Do NOT coil or knot electrical cords,

and ensure electrical cords are not trip

hazards.

General Service Information

•The equipment must be serviced or

repaired at authorised service centres

by qualified personnel only.

•Replacement parts must be original

equipment manufacturer (OEM) to

ensure equipment safety is maintained.

•Do NOT attempt any maintenance or

repair work not described in this

manual.

•After use, the equipment and

components may still be hot – allow the

equipment to cool and disconnect spark

plugs and/or electrical power sources

and/or batteries from it before making

adjustments, changing accessories or

performing repair or maintenance.

•Do NOT make adjustments while the

equipment is running.

•Perform service related activities in

suitable conditions, such as a

workshop.

•Replace worn, damaged or missing

warning/safety labels immediately.

Battery Maintenance and Charging Instructions

•You MUST charge completely prior to initial use.

•Charge immediately after each use.

•Charge before storage. You must charge every 30 days if not in use.

•Charge the unit for 6-8 hours or until the light on the charger turns red& green.

•DO NOT allows this unit to deep discharge the battery.

•For safety purposes, DO NOT charge for over 24 hours.

•Turn the unit OFF when not in use.

•In the use of electric skateboards user should check handlebar, saddles, saddle tube and wheel fastener whether tighten, folding

institutions locking structure whether lock, should pay attention to the safety of saddle tube; Should check whether the brake

effectively.

Electric Scooter Safety

•THIS PRODUCT IS NOT INTENDED FOR EXTREME or OFF-ROAD USE! Please take proper care of your electric scooter!

•DO NOT JUMP or ABUSE THIS PRODUCT!

•DO NOT RIDE IN WET/ICY CONDITIONS!

•Failure to follow these instructions will VOID YOUR WARRANTY!

•This product does not conform to Federal Motor Vehicle Standards and is not intended for operation on public streets, roads or

highways. Serious injury can result from the unsafe operations of this product. Operator can minimize these risks by using certain

safety equipment such as: safety helmet, goggles, gloves, elbow and kneepads and appropriate footwear.

•DO NOT operate in traffic, on wet, frozen, oily or unpaved surfaces or under the influence of drugs and/or alcohol. Avoid uneven

surfaces, potholes, surface cracks and obstacles.

•DO NOT use a water hose to clean this product. See Product Handbook for more information.

•This product is recommended for riders 13 YEARS OF AGE and older.

•Persons without excellent vision, balance, coordination, reflex, muscle and bone strength and good decision-making capabilities

should not use this product.

•Minors without adult supervision should not use this product.

•Persons unwilling or unable to take responsibility for their own actions should not use this product.

•The user of this product assumes ALL risks associated with its associated with its use. To minimize these RISKS, the user must wear

safety helmet, goggles, gloves, elbow and kneepads and appropriate footwear.

•This product is ELECTRIC! DO NOT ride this product in wet conditions, puddles or rainy weather.

•The recommended minimum age for riding this scooter is 13 years old.

•To avoid damage to the motor and footplate, do not overload the scooter.

•Never ride with more than one person.

•Inspect your scooter thoroughly before each use for loose or missing parts.

•Avoid unintentional starts by turning the scooter off while not in use.

•To avoid the risk of a short circuit in the electrical parts, do not use your Electric scooter in the rain and never spray or wash off your

scooter with water.

Electric Scooter

•Do not place the battery near fire or heat.

•To avoid damage to the battery, do not use the charger if it has been damaged in any way.

•Keep hands, face, feet and hair away from all moving parts.

•Do not touch the motor or wheels while they are rotating.

•Brakes are designed to control speed as well as stop the scooter. Practice braking for proper slowing down and smooth stops.

•Maintain your SCOOTER as recommended in this Product Handbook.

•Use only quality replacement parts as recommended by the manufacturer.

•Inspect the entire scooter prior to each use. Replace any part that is cracked, chipped or damaged before use.

•NEVER ALLOW CHILDREN TO OPERATE THE SCOOTER WITHOUT ADULT SUPERVISION.

•NEVER ATTEMPT TO OPERATE THE SCOOTER WHILE UNDER THE INFLUENCE OF ALCOHOL.

•If a situation arises that is not covered in the manual, proceed with caution and use good judgment.

Electric Scooter

Safety Symbols

The product may have safety warning labels attached to it, explained below. Understand the symbols

on your product and their meanings. If any stickers become unreadable, unattached etc, replace them.

Flammable Material Hazard

Flammable liquids, gases or

substances etc may present.

Avoid ignition sources and

open flames. Danger of fire.

Read User Manual

Read and fully understand

product safety warnings,

operation, procedures etc

before using the product.

Use Hand Protection

Wear appropriate hand

protection and take due care

as the product or use of the

product may present hand

hazards.

Carbon-Monoxide Hazard

Do not use the product in

confined areas or without

adequate ventilation. Carbon-

monoxide poisoning can be

fatal.

Electrocution / Electrical

Shock Hazard

High voltage or high current

electricity may be present or

required by the product. Take

due care when handling

electrical products, cables,

plugs and leads. Electrical

shock can be fatal.

Toxic Fumes / Dust Hazard

Using the product or by-

products from use may

produce fumes, smoke or

particles that could be harmful

if inhaled. Wear appropriate

breathing protection and have

adequate ventilation.

Explosive Material Hazard

Combustible liquids, gases or

substances etc may be

present. Avoid ignition sources

and open flames. Danger of

explosion.

Cutting / Amputation Hazard

The product may have blades,

edges or mechanical devices

that can cause severe cut

injury to fingers, limbs etc.

Take due care when handling

and using the product.

Crush Hazard

The product may have blades,

edges or mechanical devices

that can cause severe crush

injury to fingers, limbs etc.

Take due care when handling

and using the product.

Single Operator Only

The product must be operated

by a single person only. More

than one person operating the

product may introduce

additional hazards.

Use Face Protection

Wear appropriate full-face

protection and take due care

as the product or use of the

product may present face and

eye hazards.

Use Foot Protection

Wear appropriate foot

protection and take due care

as the product or use of the

product may present foot

hazards.

Use Eye / Ear / Head

Protection

Wear appropriate eye and / or

ear and / or head protection

and take due care as the

product or use of the product

may present eye, hearing and

head hazards.

Running Hazard

Do not run on or near the

product as doing so may

present a fall hazard.

Diving Hazard

Do not dive into the product as

doing so may present a neck /

head injury hazard.

Adult Supervision Required

Always supervise children and

other users of a product to

prevent drowning or injury.

Skin Penetration / Puncture

Hazard

The product may produce

pressure, emit liquids or

objects that can cause severe

injury to fingers, limbs, blood

etc. Take due care when

handling and using the

product.

Hot Surface Hazard

Be aware that the product may

produce high temperatures

and hot surfaces that can

cause burn injuries.

Flying Debris Hazard

Be aware that the product or

use of the product may

present hazards produced by

flying debris. Wear appropriate

clothing and protectiove

devices.

Moving Parts Hazard

Be aware that the product

contains or uses mechanical

devices that move or rotate.

Always wait for moving parts

to stop fully before handling

the product, adjusting,

maintenence etc.

Electric Scooter

Carbon-Monoxide Hazard

Do not use the product in

confined areas or without

adequate ventilation. Carbon-

monoxide poisoning can be

fatal.

Pull Hazard

Be aware that the product

contains or uses mechanical

devices that can pull in objects

and can cause severe injury to

fingers, limbs etc. Take due

care when handling and using

the product.

Slope / Fall Injury Hazard

Be aware that using the

product on sloping surfaces or

in slippery conditions may

present additional dangers

from falls and contact with

blades, moving parts, hot

surfaces etc.

"Slam Dunk" Warning

Do NOT attempt "slam dunk"

maneouvres as this may result

in severe injury due to falling,

product breakage or collapse

etc.

Electrocution / Electrical

Shock Hazard - Outdoor

High voltage or high current

electricity may be present or

required by the product. Do

NOT use in rain, damp or wet

conditions. Electrical shock

can be fatal.

Electrocution / Electrical

Shock Hazard - Disconnect

High voltage or high current

electricity may be present or

required by the product.

Always disconnect the product

from the electrical supply

before handling the product,

adjusting, maintenence etc.

Power Line Electrocution

Hazard

High voltage / high current

power lines may be present.

Use extreme caution to avoid

contact or interference with

power lines. Electrical shock

can be fatal.

"Kick-Back" Hazard

High level of "kick-back"

hazard that can cause the

machine to suddenly rotate

towards operator. Kick-back

injury can be fatal.

Winch Operator Position

Hazard

Do NOT stand between winch

and load. Do NOT use winch

to move people.

Winch Lift Hazard

Do NOT LIFT load vertically.

Use machine to PULL only.

Cable Hazard

Ensure that load bearing cable

is not kinked or knotted.

Winch Cable Hazard

Ensure that there is a

minimum number of cable

coils on winching mechanism.

Winch Hook Hazard

Carry hook to load – do NOT

throw or run.

Flash / Blinding Hazard

Wear appropriate eye

protection for welding. Dorect

exposure to weld arcs may

cause permanent eye injury.

Laser Hazard

Laser may be in use – do NOT

look directly at laser, or allow

others to.

Electric Scooter

Table of Contents

Safety...................................................................................................................................................2

Safety Symbols ..........................................................................................................................................5

Parts Identification.............................................................................................................................8

Assembly and Set-Up........................................................................................................................9

Operation ..........................................................................................................................................11

Charging the Battery ................................................................................................................................11

Riding.......................................................................................................................................................11

Stopping and Braking...............................................................................................................................12

Folding and Storage.................................................................................................................................12

Braking System........................................................................................................................................ 12

Adjusting the Brakes..........................................................................................................................12

Squeaky Brakes ................................................................................................................................13

Tyre Pressure ..........................................................................................................................................13

Lead-Acid Battery Care and Maintenance ....................................................................................14

Top 3 Battery Care Requirements ...........................................................................................................14

Maintenance .....................................................................................................................................15

Adjusting the Head Unit ...........................................................................................................................15

Adjusting the Chain..................................................................................................................................15

Maintenance Schedule.............................................................................................................................16

Daily Maintenance .............................................................................................................................16

Troubleshooting...............................................................................................................................17

Specifications...................................................................................................................................18

Electric Scooter

Parts Identification

No. Name

1 Variable speed throttle

2 Front wheel hand brake

3 Rear wheel hand brake

4 Front shock absorber

5

10” aluminium wheels

6

Seat kit (included)

7 Motor

8 Rear brake

9 Rear shock absorber

2

1

4

5

3

6

7

9

8

BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET

Electric Scooter

Assembly and Set-Up

1. Carefully remove the scooter from the box.

Then install the wheels.

2. To unfold the scooter, begin by pressing

down on the Folding Handle with one hand

while gently pulling up on the handlebars

with the other hand.

3. Fully extend the handlebars to their upright

position until you feel the mechanism lock

into place.

4. Attach the handlebars by inserting the silver

handlebar clamp onto the handlebar post,

stopping just below the top. Be sure to orient

the bars in the correct riding position with the

throttle on the rider’s right side. Secure the

handlebars to the post by tightening the bolts

on the clamp with an Allen key (not

included).

5. Secure the hand brakes in place by using an

Allen key to first loosen the tension bolts.

Adjust the levers to a comfortable position

and tighten the bolts. BE CAREFUL NOT TO

PULL ON THE CABLES!

6. Insert the 25amp fuse by opening the

footplate cover as shown. Insert the fuse into

the fuse holder, then close the footplate

cover.

BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET

Electric Scooter

7. Attach the seat post to the seat post receiver,

and then attach the clamp to the top of the

seat post. Pull the upper seat post to the

desired position and tighten the clamp

securely.

8. Attach the seat to the upper seat post and tighten the seat bolts as shown.

BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET

Electric Scooter

Operation

ATTENTION: Monitor battery usage when in use, the scooter may suddenly slow down

as the battery charge reduces.

Charging the Battery

Your scooter comes charged out of the carton. We still recommend charging the unit for 6-8 hours prior

to its first use. We also recommend charging your scooter after each use and prior to storage.

WARNING: Do not allow the electric scooter to go into deep discharge, as this will

damage the batteries.

1. Make sure the scooter is turned OFF.

2. Open the charging socket cover located on

the right side of the scooter frame, under the

footplate.

3. Locate your Battery Charger. Find the

charger socket and plug it into the scooter.

4. Next, plug the charger’s AC into a wall outlet.

When first plugged in, the charger has one red light that will illuminate at the same time, indicating that

the charging process has started. Once the light on the charger turns red &green, you may remove the

charger and close the safety cap.

Riding

1. Ensure that all exposed bolts and screws are securely tightened.

2. Raise the kickstand to its upright position.

3. Push the ON/OFF switch (located on the handlebar) to the ON position.

4. Put one foot on the deck of the scooter while pushing off with the other foot, gently rotate the

throttle grip located on the right side of the handlebars. The scooter will begin to move on its own.

NOTE: Your scooter has a variable speed hand throttle. You can control the speed of your scooter

by the amount of pressure you use when rotating the hand throttle. The more you rotate, the faster

you will go.

BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET

Electric Scooter

Stopping and Braking

To brake, release the throttle grip and depress the brake levers (on the left/right side of the handlebars).

Depressing the brake will disengage power to the motor. When the unit feels like it is losing power or

not accelerating to full speed, the scooter is ready to be re-charged.

NOTE: If the ON/OFF switch is left in the ON position for more than 10-15 minutes without moving,

Smart Power will shut itself OFF. To reset, turn the unit OFF, wait a few seconds and then switch it

back ON again.

Folding and Storage

When you are done riding the scooter, you can fold it down

for compact storage and transportation.

1. First remove the seat post and seat, then using one

hand, push down on the folding handle while gently

pushing down on the handlebars.

BE CAREFUL NOT TO HIT YOUR HEAD WITH THE

HANDLEBAR, SET YOURSELF AT THE RIGHT SIDE,

IF NECESSARY.

2. Push down until you feel the mechanism lock into a

downward position.

Braking System

The scooter uses a pinch braking system for the front, and a disc/calliper system for the rear. They are

both activated by a hand brake lever on the left and right side of the handlebar. Squeezing the hand

brake lever with your left hand actives the rear brake. Squeezing the hand brake lever with your right

hand actives the front brakes. Your scooter is equipped with switches on each brake lever that will

disengage power to the motor when motor when the brake levers are depressed.

Practice braking on a smooth, dry surface to get used to the feel of the braking system. Braking

distance is affected by wet conditions and loose, uneven riding surfaces.

Adjusting the Brakes

The Brakes on the scooter should come fully adjusted form the factory. However, it may be necessary

to adjust the brakes from time to time.

To adjust the rear brakes:

•For brakes that are adjusted too loose:

Adjust the tension screw on the right-hand brake lever by rotating it anti clockwise until the wheel

spins freely.

•For brakes that are adjusted too tight:

Tighten the tension screw on the right-hand brake lever by rotating it clockwise until the wheel has a

slight drag.

BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET

Electric Scooter

To adjust the front brakes:

•

For brakes that are adjusted too loose:

Adjust the tension screw on the left-hand

brake lever by rotating it counter-clockwise

until the wheel spins freely.

•

For brakes that are adjusted too tight:

Tighten the tension screw on the left-hand

brake lever by rotating it clockwise until the

wheel has a slight drag.

•For further front break Adjustment

Locate the adjustment screw on the front brake assembly (located above the front wheel). Tighten

or loosen as necessary.

Squeaky Brakes

The brakes may squeak before they are broken in. This is normal and will not affect the function or

performance of the brakes. With continued use, the squeak should go away.

Tyre Pressure

The tyre must be inflated to a maximum of 50 PSI. It is also recommended to use a tube additive,

available from any motorcycle shop, to avoid inconvenient punctures. Empty all air from the tyre, prior

to loosening the bolt to split the rim.

BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET

Electric Scooter

Lead-Acid Battery Care and Maintenance

Top 3 Battery Care Requirements

1. Charge battery before first use. The battery may arrive with some charge, regardless of

this the battery must be charged for 8 on the initial charge and 6-8 for each subsequent

charge.

2. Charge battery immediately when it is depleted. Do not store a depleted battery. This will

permanently impact the life of the battery. If the battery is going to be stored for a period of

time, fully charge the battery before storing.

To ensure the battery maintains optimum performance, follow the guidelines outlined below.

•For best results, charge batteries in temperatures between 10°C and 30°C

•When battery is charged, disconnect the charger from the power supply and remove the battery

from the charger.

•Inspect the terminals, screws, clamps and cables for breakage, damage or loose connections.

These should be clean, tight and free of corrosion.

•Use only with the battery charger specified by the manufacturer.

•Ensure that the battery charger electrical cord is not subjected to damage or stress. Do not operate

the battery charger if it has a damaged electrical cord or plug.

•Do not use the charger in wet areas or expose it to rain or water.

•Keep the battery clean, dry, free of dirt and grime. A dirty battery can discharge across the grime on

top of the battery casing.

•Apply a thin coating of high temperature grease to posts and cable connections for added

protection.

•Inspect the battery case for obvious signs of physical damage or warpage. This usually indicates

the battery has been overheated or has been overcharged.

•Batteries can explode in the presence of an ignition source, such as a pilot light. To reduce the risk

of serious personal injury, never use any cordless product in the presence of open ﬂame. Exploding

batteries can propel debris and chemicals.

•Do not open the battery – danger of short-circuiting and/or explosion.

•Do not attempt to destroy or disassemble the battery pack or remove any of its components.

•Do not touch the battery terminals with metal objects and/or body parts as short-circuit and/or

personal injury may result.

•Explosion hazard – protect the battery against heat; for example, direct sunlight and fire. Do not

store batteries in vehicles or locations subject to heat.

•Explosion hazard – do not open and/or short-circuit the battery.

•Poison hazard – battery leakage (liquid ejection). Under extreme conditions, liquid may be ejected

from the battery – avoid contact. If contact accidentally occurs, immediately seek medical attention,

and flush with water. If liquid contacts eyes, immediately seek medical attention, flush with clean

water for at least 10 minutes. Liquid ejected from the battery may cause irritation or burns.

•Dispose of non-serviceable batteries in an environmentally responsible manner and according to

local regulations.

Failure to adhere to the requirements above may result in the battery becoming inoperative or battery

life being reduced. In extreme cases or abuse, battery overheating or fire may result.

BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET

Electric Scooter

Maintenance

To adjust and service the scooter, you will need the following tools:

•Allen Keys: 3/4/5/6 mm

•Wrenches: 10/13/13 mm Open end wrench

•Large Adjustable Crescent Wrench

•Philips Head Screwdrivers

•Oil, Grease or Lubricant

Adjusting the Head Unit

The head unit will come adjusted from the factory. However,

riding on rough terrain and general use may cause the head

unit to become loose over time. It may be necessary to adjust

the head unit from time to time.

To adjust the head unit:

1. Rotate the handle bar as far right as it will go to expose the

head unit.

2. Using a large adjustable wrench, gently turn the bearing

lock clockwise to tighten. DO NOT OVER-TIGHTEN OR IT

WILL DAMAGE THE BEARINGS.

Adjusting the Chain

The chain will come adjusted from the factory. However, it may be necessary to adjust the chain from

time to time. The chain must be well aligned onto the sprockets in order to avoid uneven wear. This will

result in shortened chain life.

How tight should the chain be?

•If the chain is skipping or jumping on the sprockets, this is too loose and may be harmful.

•If the chain is making a humming sound when the wheel is turning, this is too tight and may cause

the chain to snap.

•The correct tension is achieved by adjusting the chain from its loose position to when it becomes

lightly tense.

To tighten the chains:

1. Slightly loosen the two axle bolls on the both sides of the rear wheel. Then, slowly adjust the two

adjusting screws on each side of the rear tyre until chain reaches the proper tension.

2. Rotate the rear wheel to make sure the chain is aligned.

3. Finally, lock and tighten the rear axle bolts prior to riding.

BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET

Electric Scooter

Maintenance Schedule

Proper care of your scooter will ensure optimal performance and longer life span. The following are a

few maintenance suggestions that will keep your scooter running in top condition.

Daily Maintenance

Perform these each time you ride your scooter.

•Clean the exterior of the unit with a soft, damp rag (DO NOT WASH DOWN WITH A HOSE).

•Check that all nuts and bolts are securely tightened.

•Lubricate the chain with any silicone spray, 3&1 oil or any good, clean motor oil.

•Check battery charger for any frayed/cut wires.

•Check the power cords if they are cut of frayed, the motor gear if it is worn, and/or if there are any

loose bolts.

•Check if there are any loose connectors or bolts.

BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET

Electric Scooter

Troubleshooting

SYMPYTONS POTENTIAL CAUSE SOLUTION

The charger light turns green & red

right away.

This indicates the batteries are

adequately charged.

Bad Fuse or open connection

between charger socket and

batteries.

Continue to charge the

batteries for 6-8 hours prior to

initial use.

Check fuse. Look for loose or

disconnected wires.

Batteries do not hold a charge.

Scooter does not have specified

travel range.

Batteries have reached the end

of their useful life.

Charger is malfunctioning

Replace batteries.

Replace charger unit.

Unit moves intermittently or very

slowly.

Batteries not fully charged.

Loose wires.

Faulty throttle or controller.

Charge or replace batteries.

Check for loose wires.

Replace throttle or controller.

Unit will not move when throttle

lever is activated.

Batteries not fully charged.

Brake switches out of

adjustment.

Batteries have reached the end

of their useful life.

Replace batteries or charger.

Loosen brakes.

Replace batteries.

Unit stops abruptly during use.

Fuse blown.

Loose or broken wire.

Replace fuse

Check for loose or broken

wires and repair/replace.

BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET

Electric Scooter

Specifications

Motor 1000W/ 1600W Peak

Battery Pack 48V 12Ah

Top Speed 50km/h (mode, terrain, riding style, weight dependant)

Range 35 km/h (mode, terrain, riding style, weight dependant)

Wheelbase 97cm

Max Rider Weight 120kg

Charging time 6-8 hours

Charging Voltage 220-240v

Drive Train Chain

Deck ABS Resin

Brake Disc/Disc

Tyres Pneumatic 10” Knobby

Battery Type Acid-Lead

Power Plug Australian Standard

IMPORTANT: Always remember to wear a helmet. This scooter must not be used on sealed or

unsealed public roads or public spaces, wet conditions, or for stunts.

BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET BULLET

Some experts believe that the incorrect or prolonged use of almost any

product may cause serious injury or death. To help reduce your risk of

serious injury or death, refer to the information below. For more information,

see www.datastreamserver.com/safety

Consult all documentation, packaging

and product labelling before use. Note

that some products feature

documentation available online. It is

recommended to print and retain the

documentation.

Before each use, check the product for

loose/broken/damaged/missing parts,

wear or leaks (if applicable). Never use a

product with

loose/broken/damaged/missing parts,

wear or leaks.

Products must be inspected and serviced

(if applicable) by a qualified technician

every 6 months. This is based on

average residential use by persons of

average size and strength, and on a

property of average metropolitan size.

Use beyond these recommendations may

require more frequent

inspections/servicing.

Ensure that all users of the product have

completed a suitable industry recognised

training course before being allowed

access to the product.

The product has been supplied by a general merchandise

retailer that may not be familiar with your specific

application or description of application. Be sure to attain

third-party approval from a qualified specialist for your

application before use, regardless of any assurances from

the retailer or its representatives.

This product is not intended for use where fail-safe

operation is required. As with any product (for example,

automobile, computer, toaster), there is the possibility of

technical issues that may require the repair or

replacement of parts, or the product itself. If the possibility

of such failure and the associated time it may take to

rectify could in any way inconvenience the user, business

or employee, or financially affect the user, business or

employee, then the product is not suitable for your

requirements. This product is not intended for use where

incorrect operation or a failure of any kind, including but

not limited to, a condition requiring product return,

replacement, parts replacement or service by a technician

may cause financial loss, loss of employee time or an

inconvenience requiring compensation.

If this product has been purchased in error when

considering the information presented here, contact the

retailer directly for details of their returns policy, if

required.

diagrams or images may be reproduced or transmitted in any form or by any means, electronic or

mechanical, including photocopying, scanning or recording, or any information storage and retrieval system,

without express permission or consent from the publisher.

Bullet Electric Scooter User manual

Popular Scooter manuals by other brands