Bullet ZPS User manual

Page1
Electric Scooter
Owner’s Manual

Page2
PLEASE BE SAFE WHEN RIDING
ALWAYS WEAR A HELMET AND OBEY ALL LAWS!
BATTERY MAINTENANCE and
CHARGING INSTRUCTIONS
You MUST charge completely prior to initial use.
(Follow charging instructions in your Product Handbook)
1. Charge immediately after each use.
2. Charge before storage. You must charge every 30 days if not
in use. Charge the unit for 6-8 hours until the light on the
charger turns green.
3. DO NOT allow this unit to deep discharge the battery.
4. For safety purposes, DO NOT charge for over 8 hours.
5. Turn the unit OFF when not in use.
不
This PRODUCT IS NOT INTENDED FOR EXTREME or
OFF-ROAD Use! Please take care of your ELECTRIC
SCOOTER!
DO NOT JUMP or ABUSE THIS PRODUCT!
DO NOT RIDE IN WET/ICY CONDITIONS!
DO NOT RIDE INDOORS
The appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning
the use of the appliance by a person responsible for their safety
IMPORTANT
注意
Failure to follow these INSTRUCTIONS will
VOID YOUR WARRANTY!

Page3
PACKAGE CONTENTS
Your ELECTRIC SCOOTER comes with the following items in the box. Please
locate all of the following
1. The ELECTRIC SCOOTER
2. Battery Charger
3. Tool Kit
4. Product Handbook
WARNING
Persons without excellent vision, balance, coordination, reflex, muscle and
bone strength and good decision-making capabilities should not use this
product.
User: 7+ ages, suggest use the product with adult supervision at all times.
Minors without adult supervision should not use this product.
Persons unwilling or unable to take responsibility for their own actions should
not use this product.
The user of this product assumes ALL risks associated with its use. To
minimize these RISKS, the user must wear safety helmet, goggles, gloves,
elbow and kneepads and appropriate footwear.
This product is ELECTRIC! DO NOT ride this product in wet conditions, puddles
or rainy weather.
This products should be assembled and adjusted well by adult, then chidren can drive
it.
IMPORTANT
PLEASE READ THIS BEFORE USING THIS PRODUCT
READ THIS FIRST!

Page4
GETTING STARTED
Please read and understand these instructions and the OPERATING
PROCEDURES section, prior to starting or riding your ELECTRIC
SCOOTER
Assembly
1. Open the box, and take out the scooter and pneunatic front tyre, then fix the front tyre（photos
②）like below photos shows，make it matched with the front fork (photos ③) , and insert the
bolt stud (photos ①), make it through the bearing hole. after finished it, please tighten it by allen
wrench: M5.
②
①
③
Pick up the steering lever （①）, and put it into front fork （photos ②）. Make sure the insert
depth must over the marked line on the tube, like the belowing photo shows （③）.And keep the
same direction between scuttle and chasis.
①
③
②

Page5
3. Handlebar fixing;
a. Place the handlebar (1) into the steering stem clamp (2) so that it is centered and resting in
the channel.
b. Place the steering stem top clamp (3) into position over the handlebar. Fasten it using 2 M5
screws. Tighten the screws using the allen key.
c. Adjust the handlebar direction, make sure it is set perpendicular to the front wheel, and then
fasten the steering stem clamp (4) using the 2 M5 screws and nuts (5). Tighten the screws
using the allen key and spanner.
d. Check that the handlebar mounted brake system works properly, and when released, that front
wheel can rotate freely.

Page6
Charging
WARNING: Do not allow your scooter to go into deep discharge, as this will damage the
batteries.
1. Make sure unit is turned off.
2. Charging socket is located on side. (see picture below)
3. Locate your Battery Charger. Find the charger socket end that has a
single-prong socket and plug it into the scooter.
4. Next, plug theAC plug into a wall outlet.
When first plugged in, the charger will have one red light that will illuminate as long as the
power switch is in the charge position, if the power switch is in the on or off position the
charger will have a red and green light illuminating which means no charge is taking place.
Make sure you have the switch in the correct charge position. After 4-8 hours the green
light on the charger is illuminated indicating the unit is now charged.
3 Control Switch
1. ON - Turn the scooter ON for riding (the scooter must have sufficient charge).
2. OFF - Turn the scooter OFF. Always turn the scooter OFF when not in use to preserve
battery charge and maximise battery life and performance.
3. CHA - Place the scooter in battery charging mode. The scooter can be charged only
when in charging mode.

Page7
Circuit Breaker
When the current is too high, the fuse will pop up, you only need to press it down, the
scooter can work again, no need to change fuse
Riding
1. Make sure that all of the exposed bolts and screws are tightened.
2. Raise the kickstand to its up position.
3. Push the switch to the ON position
4. Put one foot on the deck of the ELECTRIC SCOOTER while pushing off with the other
foot, gently rotate the THROTTLE GRIP, on the right side of the handlebars. The
ELECTRIC SCOOTER will begin to move on its own power.
Your scooter has a variable speed hand throttle. You can control the speed of your scooter
by the amount of pressure you use when rotating the hand throttle. The more you rotate,
the faster you will go.
Please ensure this small grub screw is secure and tight using the Allen wrench:M2.5
provided.
Stopping/Braking
1. To brake, release the THROTTLE GRIP and depress the BRAKE LEVER (on the left
side of the handlebars. Depressing the brake will disengage power to the motor.
When the unit feels like it is loosing power or not accelerating to full speed, the scooter
is ready to be re-charged.

Page8
BRAKING SYSTEM
The ELECTRIC SCOOTER uses a hub brake system on the rear wheel. A hand brake
lever on the left side of the handlebar activates the brakes. Squeezing the hand brake
lever with your left hand will activate the rear brake. Make sure to release the HAND
THROTTLE GRIP when engaging the brakes.
Practice braking on a smooth, dry surface to get used to the feel of the braking system.
Braking distance is affected by wet conditions and loose and uneven riding surfaces.
Adjusting the Brakes
The Brakes on the ELECTRIC SCOOTER should come fully adjusted from the
factory.
However, it may be necessary to adjust the brakes from time to time.
Squeaky Brakes
The brakes may squeak before they are broken in. This is normal and will not
affect the function or performance of the brakes. With continued use the
squeak should go away.
To adjust the rear brakes:
For brakes that are adjusted too tight
1. Loosen the tension screw on the left
hand brake lever by rotating it
counter-clockwise until the wheel
spins freely.
For brakes that are adjusted too loose
1. Tighten the tension screw on the left
hand brake lever by rotating it
clockwise until the wheel has a slight
drag.
For further adjustment, locate the
adjustment screw on the rear brake hub
located on the rear wheel.

Page9
Allen Wrenches: M5，M2.5
Wrenches: M13-15，M8-10
MAINTENANCE SCHEDULE
Proper care of your ELECTRIC SCOOTER will insure optimal performance
and longer life span. The following are a few maintenance suggestions that will
keep your ELECTRIC SCOOTER running in top condition:
Daily Maintenance
Perform each time you ride your ELECTRIC SCOOTER
Clean the exterior of the unit with a soft, damp rag.
Check that all nuts and bolts are securely tightened.
Check battery charger for any frayed/cut wires.
MAINTENANCE
RECOMMENDED TOOLS
To adjust and service the ELECTRIC SCOOTER you will need the following
tools:

Some experts believe the incorrect or prolonged use of almost any
product could causeserious injury or death. For information that
may reduce your risk of serious injury or death consult thepoints
below and additionally, the information available at
www.datastreamserver.com/safety
- Consult all documentation, packaging and
product labelling be fore use. Note that some
products feature online documentation which
should be printed and kept with the product.
-Check product for loose / broken / damaged /
missing parts, wear or leaks (if applicable) be fore
each use. Never use a product with loose / broken
/ damaged / missing parts, wear or leaks (if
applicable).
- Products must be inspected and serviced (if
applicable) by a qualified specialist every 6
months assuming average residential use by a
person of average weight and strength, ab ove
average technical aptitude, on a property
matching average metropolitan specification.
Intended use outside these guidelines could
indicate the product is not suitable for intended
use or may require more regular inspection or
servicing.
- Ensure all possible users of the p roduct have
completed an industry recognised training course
before being given access to the product.
- The product has been supplied by a general merchandise
retailer that may not be familiar with your specific applic ation or
your description of the application. Be sure to attain third party
approval for your application from a qualified specialist before use
regardless of prior assurances by the retailer or its representatives.
- This product is not intended for use where fail-safe operation is
required. As with any product (take an automobile, aircraft,
computer or ball point pen for example) there is always a small
chance of a technical issue that needs to be repaired or may
require replacement of the product or a part. If the possibility of
such failure and the associated time it takes to rectify could in any
situation inconvenience the user, business or employee or could
financially affect the user, business or employee then the product
is not suitable for your requirements. This p roduct is not for use
where incorrect operation or a failure of any kind, including but
not limited to a condition requiring product return, replacement,
service by a technician or replacement of parts could cause a
financial loss, loss of employee time or an in convenience
requiring compensation.
- If this item has been purchased in error considering the points
above simply contact the retailer directly for details of their
returns policies if required.