Burkert 8030 HT User manual

Type 8030HT - SE30HT
High Temperature
Flowmeter with paddle wheel
and ow transmitter
Operating Instructions
Bedienungsanleitung
Manuel d'utilisation

www.burkert.com
We reserve the right to make technical changes without notice.
Technische Änderungen vorbehalten.
Sous réserve de modication technique.
© Bürkert SAS, 2013–2022
Operating Instructions 2201/03_EU-ML 00449752 / Original EN

2
1. ABOUT THESE OPERATING INSTRUCTIONS ...... 3
2. INTENDED USE ...................................................... 6
3. BASIC SAFETY INFORMATION.............................. 7
4. GENERAL INFORMATION .................................... 10
5. DESCRIPTION ...................................................... 11
6. TECHNICAL DATA ................................................ 14
7. INSTALLATION AND COMMISSIONING ............. 19
8. MAINTENANCE .................................................... 33
9. ACCESSORIES .................................................... 35
10. PACKAGING, TRANSPORT ................................. 36
11. STORAGE ............................................................. 36
12. DISPOSAL OF THE DEVICE ................................. 37
English

3
1. ABOUT THESE OPERATING
INSTRUCTIONS
The Operating Instructions describe the entire life cycle
of the device. Please keep the Operating Instructions
in a safe place, accessible to all users and any new
owners.
The Operating Instructions contain important safety
information.
Failure to comply with these instructions can lead to
hazardous situations. Pay attention in particular to the
chapters 3. Basic safety information and 2. Intended
use.
▶Whatever the version of the device, the Operating
Instructions must be read and understood.
English 3

4
Symbols used
DANGER
Warns against an imminent danger.
▶Failure to observe this warning can result in death or
in serious injury.
WARNING
Warns against a potentially dangerous situation.
▶Failure to observe this warning can result in serious
injury or even death.
CAUTION
Warns against a possible risk.
▶Failure to observe this warning can result in sub-
stantial or minor injuries.
NOTE
Warns against material damage.
Indicates additional information, advice or
important recommendations.
English

5
Refers to information contained in these Oper-
ating Instructions or in other documents.
▶Indicates an instruction to be carried out to avoid a
danger, a warning or a possible risk.
→Indicates a procedure to be carried out.
Denition of the word "device"
The word "device" used within these Operating Instruc-
tions refers to the owmeter type8030HT or to the ow
transmitter typeSE30HT (high temperature).
English 5

6
2. INTENDED USE
Use of the device that does not comply with the
instructions could present risks to people, nearby
installations and the environment.
The 8030 HT owmeter and the SE30HT ow trans-
mitter are intended exclusively to measure ow rate in
liquids.
▶The device must be protected against electro-
magnetic interference, ultraviolet rays and, when
installed outdoors, the eects of climatic conditions.
▶The device must be used in compliance with the
characteristics and commissioning and use condi-
tions specied in the contractual documents and in
the Operating Instructions.
▶Requirements for the safe and proper opera-
tion of the device are proper transport, storage
and installation, as well as careful operation and
maintenance.
▶Only use the device as intended.
English

7
3. BASIC SAFETY INFORMATION
This safety information does not take into account any
contingencies or occurrences that may arise during
installation, use and maintenance of the device.
The operating company is responsible for the respect of
the local safety regulations including for the sta safety.
Danger due to high pressure in the installation.
Danger due to electrical voltage.
Danger due to high temperatures of the uid.
Danger due to the nature of the uid.
Various dangerous situations
▶Prevent any unintentional power supply switch-on.
▶Ensure that installation and maintenance work are
carried out by qualied, authorised personnel in
possession of the appropriate tools.
English 7

8
Various dangerous situations
▶Guarantee a set or controlled restarting of the pro-
cess, after a power supply interruption.
▶Use the device only if in perfect working order and
in compliance with the instructions provided in the
Operating Instructions.
▶Observe the general technical rules when installing
and using the device.
▶Do not use the device in explosive atmospheres.
▶Do not use the device for the measurement of gas
ow rates.
▶Do not use uid that is incompatible with the mate-
rials the device is made of.
▶Do not use the device in an environment incompat-
ible with the materials it is made of.
▶Do not subject the device to mechanical loads.
▶Do not make any external or internal modications
to the device.
English

9
NOTE
The device may be damaged by the uid in contact with
▶Systematically check the chemical compatibility
of the component materials of the device and the
uids likely to come into contact with them (for
example: alcohols, strong or concentrated acids,
aldehydes, alkaline compounds, esters, aliphatic
compounds, ketones, halogenated aromatics or
hydrocarbons, oxidants and chlorinated agents).
NOTE
Elements / Components sensitive to electrostatic
discharges
The device contains electronic components sensitive to
electrostatic discharges. They may be damaged if they
are touched by an electrostatically charged person or
object. In the worst case scenario, these components
are instantly destroyed or go out of order as soon as
they are activated.
▶To minimise or even avoid all damage due to an elec-
trostatic discharge, take all the precautions described
in standard EN61340-5-1.
▶Do not touch any of the live electrical components.
English 9

10
4. GENERAL INFORMATION
To contact the manufacturer of the device, use following
address:
Bürkert SAS
Rue du Giessen
BP 21
F-67220 TRIEMBACH-AU-VAL
You may also contact your local Bürkert sales oce.
The addresses of our international sales oces are
available on the internet at: country.burkert.com.
Warranty conditions
The condition governing the legal warranty is the con-
forming use of the device in observance of the operating
conditions specied in these Operating Instructions.
Information on the Internet
You can nd the Operating Instructions and tech-
nical data sheets regarding the type8030HT at:
country.burkert.com.
English

11
5. DESCRIPTION
Area of application
The 8030HT owmeter and the SE30HT ow transmitter
are intended to measure the ow rate of neutral or slightly
aggressive liquids free of solid particles.
Construction
The device is built with an SE30HT ow transmitter and
an S030HT sensor-tting incorporating the measuring
element.
The transmitter can be removed without opening the
piping or stopping the process. Depending on the
version, the device is tted with:
- 2 pulse outputs, NPN and PNP, or
- 1 sinus output.
Electrical connection is made via a male xed
connector.
English 11

12
Measuring principle
The uid owing in the piping makes the paddle-wheel
turn. The sensor detects the rotation of the paddle-
wheel thus generating a signal which frequency f is
proportional to the ow rate Q, acc. to formula:
• f = KxQ for a version with 2 pulse outputs,
• f = 2KxQ for a version with 1 sinus output,
f = frequency in Hertz (Hz)
K = K factor specic to each sensor-tting S030HT, in
pulse/litre
Q = ow rate in litre/second
English

13
Description of the name plate
(example)
FLOW : SE30 / 8030
COIL 12-36 V DC
OPEN COLLECTOR PNP/NPN
S/N 10439
00449694 W41MG
Made in France
1
4
5
6
789
32
1. Type of ow sensor
2. Measured quantity
3. Type of the device
4. Supply voltage
5. Output data
6. Conformity marking
7. Manufacturing code
8. Serial number
9. Order code
English 13

14
6. TECHNICAL DATA
Conditions of use
Ambient
temperature
(operating)
• Version with pulse outputs:
–15°C...+80°C
• Version with sinus output:
–15°C...+100°C
Air humidity < 80%, non condensated
Protection rating
acc. to EN60529
IP65, female connector wired,
plugged and tightened
Conformity to standards and
directives
The applied standards, which verify conformity with
the EU Directives, can be found on the EU Type Exami-
nation Certicate and/or the EU Declaration of Con-
formity (if applicable).
English

15
Conformity to the Pressure Equipment
Directive
→Make sure that the device materials are compatible
with the uid.
→Make sure that the pipe DN is adapted for the device.
→Observe the uid nominal pressure (PN) for the
device. The nominal pressure (PN) is given by the
device manufacturer.
The device conforms to Article4, Paragraph1 of the
Pressure Equipment Directive 2014/68/EU under the
following conditions:
• Device used on a pipe (PS= maximum admissible pressure,
in bar; DN= nominal dimension of the pipe, no unit)
Type of uid Conditions
Fluid group1, Article4,
Paragraph1.c.i DN ≤ 25
Fluid group2, Article4,
Paragraph1.c.i
DN ≤ 32
or PSxDN≤ 1000bar
Fluid group1, Article4,
Paragraph1.c.ii
DN ≤ 25
or PSxDN≤ 2000bar
Fluid group2, Article4,
Paragraph1.c.ii
DN ≤ 200
or PS≤ 10bar
or PSxDN≤ 5000bar
English 15

16
Fluid data
Fluid pressure Depends on the uid temperature:
refer to the Operating Instructions
of the sensor-tting used.
Fluid
temperature
–15°C...+125°C
The uid temperature may be
restricted by the uid pressure:
refer to the Operating Instructions
of the sensor-tting S030HT.
Type and data of
the uid
refer to the Operating Instructions
of the sensor-tting used.
Flow rate measurement
• Measurement
range
• 0.5...10m/s
• Measurement deviation
- K-factor
standard
- ±2.5% of the measured value*
- Teach-In - ±1% of the measured value* (at
the value of the Teach-In ow rate)
• Linearity • ±0.5% of the full scale (10m/s)
• Repeatability • ±0.4% of the measured value*
* Determined in the following reference conditions: medium=
water, water and ambient temperatures 20°C, min. upstream and
downstream distances respected, appropriate pipe dimensions.
English

17
Materials
Part Material
Housing PPS, glass bre reinforced
Male xed connector PA
Female connector type
2518/ screw/ seal
PA / Stainless steel / NBR
Identication label Polyester
Sensor-tting S030HT Refer to the Operating
Instructions of the sensor-
tting used.
Electrical data
Version with pulse outputs
Supply voltage 12...36VDC, ltered and
regulated
Current consumption 10mA max.
Protection against polarity
reversal
Yes
Protection against spike
voltages
Yes
English 17

18
Version with pulse outputs
Protection against short
circuits
Yes
NPN and PNP, 700mA max., frequency up to 250Hz,
duty cycle 1/2±10%
NPN output: 0.2...30VDC
PNP output: supply voltage
Version with sinus output
Supply voltage Without
Frequency up to 500Hz, about 2.8mV peak-to-peak/
Hz under a 50kΩ load
English

19
7. INSTALLATION AND
COMMISSIONING
Safety instructions
DANGER
Risk of injury due to high pressure in the installation.
▶Stop the circulation of uid, cut o the pressure
and drain the pipe before loosening the process
connections.
Risk of burning due to high uid temperatures.
▶Use safety gloves to handle the device.
▶Stop the circulation of uid and drain the pipe
before loosening the process connections.
Risk of injury due to the nature of the uid.
▶Respect the prevailing regulations on accident preven-
tion and safety relating to the use of hazardous products.
English 19