C.A. Technologies LYNX L100CM Manual

Lynx MultiColor Spray Gun
with pressure cup
Model L100CM
C.A.Technologies
P.O.Box 17820
Boulder, CO 80301
www.spraycat.com
888 820 4498
303 438 5707
FAX: [phone]

Operation and maintenance instructions for Lynx L100CM spray guns
General description
The L100CM is a bleeder type(atomizing air flows continuously spray gun with pressurized material supply cup and
an internal mix style spray nozzle. It has been optimized for the application of multi-color coatings but also is excellent
for single color latex or oil based interior paints.
Set-up and Operation
1. Connect a REGULATED air supply hose to the ¼ fitting on gun handle.
2. Connect the paint cup attachment to the 3/8 fluid inlet fitting on gun head.
3. Attach the 1/8 nylon tube on top of paint cup lid to the pressurization port on gun head.
4. Remove paint cup and fill with material to be sprayed. Reattach cup to cover and tighten firmly.
5. Turn on air supply and adjust pressure to material suppliers recommendation for material to be sprayed. Air will
flow continuously pressurizing the paint cup.
6. Fluid flow can be controlled using the fluid control knob; this restricts flow by limiting needle travel.
Maintenance
IMPORTANT! Routine cleaning and maintenance is essential to insure proper gun operation.
Several states prohibit spraying solvent into the atmosphere and require the use of a covered gun cleaner.
1. If a gun cleaner is being used, connect and clean the gun in the gun cleaner according to the manufactures
Instructions.
2. If a gun cleaner is not being used, first clean the paint cup thoroughly then spray clean solvent thru the
gun until clean. Remove air nozzle and clean separately if necessary.
NOTE: Gun ead disassembly is not recommended for
normal cleaning and maintenance.
Gun head disassembly and reassembly instructions
NOTE! New seals must be used w en reassembling gun ead
Have repair kit No. 10-106 on and before disassembling gun ead
Gun ead disassembly
To remove the nozzle carrier (6 and air cap adapter (7 :
1. Remove the air cap (2 , fluid nozzle (3 , and needle (14
2. Remove the needle seal cartridge (24
3. Loosen the locknut (10 and remove fluid inlet (11 using a 5/8 open-end wrench.
4. The nozzle carrier and air cap adapter will now slide forward from
the gun handle (12 .
Gun ead reassembly
1. Install a new o-ring (8 on the air cap adapter
2. Install the thread locknut (10 onto the fluid inlet as far as possible.
3. Install a new seal (21 into the recess of the fluid inlet port in nozzle carrier (6
4. Slide the nozzle carrier (6 into air cap adapter (7 and insert into the gun body as far as possible. Be sure the
nozzle carrier extends into the hole at the back of the gun head. Install the needle seal (24 but do not tighten.
5. Rotate the nozzle carrier until the fluid inlet port in the nozzle carrier is aligned with the threaded hole in the
gun body while in this position, insert the fluid inlet (11 and tighten firmly.
6. Tighten the needle seal (24 to approx. 12 ft-lb. torque.
7. Tighten the fluid inlet (11 to approx. 25 ft-lb. torque.
8. Tighten the locknut (10 to approx. 33 ft-lb. torque.

.ONMETI.ONTRAPNOITPIRCSED.ONMETI.ONTRAPNOITPIRCSED
1
402-12GNIRGNINIATER71*402-06GNIRPSNRUTERELDEEN
2
322-12
422-12ro PACRIA81102-06GNIHSUBRAER
3
8170-13ELZZONDIULF91*911-06LAES
4
2022-13YDOBELZZONDIULF02903-06GULP
5
5001-16*LAES12*421-06LAESTELNIDIULF
6
C11L-06REIRRACELZZON223.4-02-35EBUTNOLYN"8/1
7
C21-06RETPADAPACRIA32205-06GNITTIFBRAB
8
131-06*GNIR-O42*0041-06YLBMESSALAESELDEEN
9
1020-02ROTCETORPDAERHT521012-06REGGIRT
01
821-06TUNKCOL62
11
621-06TELNIDIULF72401-06GNITTIFTELNIRIA
21
P-4211-06YDOBNUG823301-06TESTOVIPREGGIRT
31
221-06GLUPEVLAVRIA92901-89WERCSTES
41
8171-04YLBMESSAELDEEN03353-15YLBMESSAREVOCPUC
51
202-06BONKLORTNOCDIULF13153-25)LM057(PUC
61
*502-06TAESGNIRPS23853-15TEKSAGPUC
* PARTS INCLUDED IN REPAIR KIT 10-106

Converting t e Lynx L100CM cup gun into a ig production gun
Conversion Kit 10-400 contains:
60-503 Plug
60-1520 Air valve assembly
31-2218 Fluid nozzle body and fluid tip
61-1005 Gasket
21-1584 Retaining ring
21-200 air nozzle
21-1583 Air nozzle base assembly
40-1115 fluid needle assembly
1. Remove trigger screws (28 and remove trigger
2. Remove air valve plug (20
3. Install 60-1520 air valve assembly including spring and seal
4. Remove 1/8 nylon cup pressurization hose from barb fitting on spray head.
Remove brass barb fitting.
5. Install 60-503 brass plug into gun head.
6. Reinstall trigger and trigger screws.
The gun can now be used with the fluid nozzle and air cap supplied with the gun originally
or they can be replaced with new fluid nozzle, air nozzle, and needle as described below.
7. Remove existing air nozzle ring (1 , air nozzle (2 , fluid nozzle (3 .
8. Remove thread protector (9 .
9. Using a 1/4 Allen wrench remove fluid nozzle body (4 and gasket (5 .
10. Install new fluid nozzle body using a 15mm open end wrench and install fluid tip using 3/8 x ¼ drive socket.
11. Install new gasket 61-1005.
12. Install 21-1583 air nozzle base assembly.
13. Install 21-200 air nozzle.
14. Install new needle.