C.A. Technologies Jaguar 300 Series User manual

HVLP AIR CAP AND FLUID NOZZLE CHART
MODEL NO. AIR CAPS
*MAX GUN
INLET
PRESS. FOR
HVLP
SIDEPORT
CONTROL
SCFM @
MAX. GUN
INLET
AIR CAP
RING
AVAILABLE FLUID
NOZZLES TIPS
23-1010 45 13.5 33-0210 1.0mm (.040") 40-1310 (310)
23-1013 45 13.5 33-0213 1.3mm (.052") 40-1313 (313)
23-1014 45 13.5 33-0214 1.4mm (.055") 40-1314 (314)
J300H 23-1015 45 13.5 33-0215 1.5mm (.059") 40-1315 (315)
23-1017 45 13.5 33-0217 1.7mm (.070") 40-1317 (317)
23-1019 45 13.5 33-0219 1.9mm (.075") 40-1319 (319)
23-1022 45 13.5 33-0222 2.2mm (.086") 40-1322 (322)
CONVENT IONAL AIR CAP AND FLUID NOZZLE CHART
MODEL NO. AIR CAPS
*MAX GUN
INLET
PRESS. FOR
HVLP
SIDEPORT
CONTROL
SCFM @
MAX. GUN
INLET
AIR CAP
RING
AVAILABLE FLUID
NOZZLES TIPS
23-2013 45-55 9-10.7 33-0613 1.3mm (.051") 40-1313 (313)
J300C 23-2014 45-55 9-10.7 33-0614 1.4mm (.055") 40-1314 (314)
23-2016 45-55 9-10.7 33-0616 1.6mm (.063") 40-1315 (315)
Actual fluid nozzle and air cap combinations are determined by application (see application chart page 4)
60-1500 Included
NEEDLES /
(marking on
needle)
NEEDLES /
(marking on
needle)
60-1502 (#2)
*Note: Air cap test gages are available to confirm HVLP compliance.
Included
Jaguar 300 Series
GRAVITY FEED SPRAY GUN
PRODUCT INFORMATION
Coating Atomization Technology P O Box 17820 Boulder CO 80308 [phone] Fax [phone]
www spraycat com

Operation and maintenance instructions for Jaguar spray guns
Operation
1 Connect air supply hose at handle of gun (see page 1 for suggested gun inlet pressures)
2 The optional air control valve built into the gun handle can be used to adjust gun inlet pressure
3 Screw the paint cup onto the guns gravity feed fluid inlet
4 Fluid flow can be controlled using the fluid control knob, this restricts flow by
limiting needle travel It is best to control fluid flow by proper selection of fluid orifice
size and use the fluid control knob to  fine tune flow rate
5 Fan width can be adjusted using fan control knob Turning the knob clockwise narrow the fan
Maintenance
IMPORTANT! Routine cleaning and maintenance is essential to insure proper gun operation
Several states prohibit spraying solvent into the atmosphere and require the use of a covered gun
cleaner
1 If a gun cleaner is being used, connect and clean the gun in the gun cleaner according to the
manufactures instructions
2 If a gun cleaner is not being used:
First clean the gravity feed cup thoroughly, then spray clean solvent thru the gun until clean
NOTE: Gun head disassembly is not recommended for
normal cleaning and maintenance.
Gun head disassembly and reassembly instructions
Gun Head Disassembly
To remove the nozzle carrier (4) and air cap adapter (5):
1 Remove the air cap (1), fluid nozzle tip (2), fluid nozzle body (3), and needle (14)
2 Remove the needle seal cartridge (15)
3 Loosen the locknut (9) and remove fluid inlet (10) using an 11/16" wrench
4 The nozzle carrier and air cap adapter will now slide forward from
the gun handle (11)
Gun head reassembly
1 Install a new o-ring (7) on the air cap adapter
2 For model J300H only, install a new o-ring 98-8026 onto the air cap adapter
3 Install the thread locknut (9) onto the fluid inlet as far as possible
4 Install a new seal (8) onto the fluid inlet
5 Slide the nozzle carrier (4) into air cap adapter (5) and insert into the gun body as far as possible
Be sure the nozzle carrier extends into the hole at the back of the gun head Install the needle seal
(15) but do not tighten
6 Rotate the nozzle carrier until the fluid inlet port in the nozzle carrier is aligned with the threaded
hole in the gun body While in this position, insert the fluid inlet (10) and hand tighten firmly DO
NOT WRENCH TIGHTEN UNTIL STEP 8
7 Tighten the needle seal (15) to approx 12 ft-lb torque
8 Tighten the fluid inlet (10) to approx 25 ft-lb torque
9 Tighten the locknut (9) to approx 33 ft-lb torque

HVLP AIR CAP TEST GAUGES
FOR
J300H
GUNS
23-1010-G
23-1013-G
23-1014-G
23-1015-G
23-1017-G
23-1019-G
23-1022-G
ITEM
NUMBER PART NUMBER DESCRIPTION
1 See Air Cap Chart Air Cap (see page 1)
2 See Nozzle Chart Fluid Nozzle Tip
33-1202 Fluid Nozzle Body (for HVLP)
33-2201 (CONV.) Fluid Nozzle Body (for CONV.)
60-J31H (HVLP) Nozzle Carrier (HVLP)
60-J31C (CONV.) Nozzle Carrier (CONV.)
4-1 60-123 Carrier Seal
60-34H (HVLP) Air Cap Adapter (HVLP)
60-32C (CONV.) Air Cap Adapter (CONV.)
6 98-8026 O-Ring*
7 See KIT NO. 10-105 O-Ring*
8 See KIT NO. 10-105 Seal*
8-1 See KIT NO. 10-105 Seal*
9 60-118 Locknut
10 60-127 Fluid Inlet Fitting
60-1113 JAGUAR Gun body HVLP
60-1123 JAGUAR Gun body CONV.
12 90-0109 Allen Plug
60-1502 Fan Control Assembly (HVLP)
60-1500 Fan Control Assembly (CONV.)
14 See Air Cap Chart Fluid Needle
15 60-1400 Needle Seal Cartridge*
16 60-1033 Trigger Pivot Set
17 60-2101 Trigger
18 60-1520 Air Valve Assembly
19 60-302 Air Valve Poppet
20 See KIT NO. 10-105 Seal*
21 See KIT NO. 10-105 Air Valve Spring*
22 See KIT NO. 10-105 Seal*
23 60-201 Rear Bushing
24 See KIT NO. 10-105 Needle Return Spring
25 See KIT NO. 10-105 Spring Seat
26 60-202 Fluid Control Knob
27 60-1510 Air Control Knob (Optional)
28 60-122 Plug
29 60-104 Air Inlet Fitting
51-401 standard 750cc Gravity Feed Cup (aluminum)
51-400 optional 750cc Gravity Feed Cup (plastic)
51-403 optional 1 liter Gravity Feed Cup (aluminum)
31 51-418 Gravity Cup Lid
* Included in KIT NO. 10-105
** Included with Air Valve Assembly 60-1520
30
4
3
11
13
5

40-1314
40-1315
KITS FOR



GUNS J300H & J300C
NEEDLE
NEEDLE
40-1313
40-1310
40-1317
40-1319
40-1322
40-1310
40-1313
40-1314
40-1315
JK2016 1.6 23-2016 33-0615
33-0614
JK2013 1.3 23-2013 33-0613
JK2014 1.4 23-2014
33-0222
33-0610
CONVENTIONAL
KITS ORIFICE SIZE AIR CAP ORIFICE (TIP)
JK1010 1.0 23-2010
JK1022
ORIFICE (TIP)
23-1010
23-1013
23-1022
33-0210
33-0213
33-0214
33-0215
33-0217
33-0219
23-1017
23-1019
HVLP KITS ORIFICE SIZE AIR CAP
JK1010 1.0
JK1013 1.3
JK1015 1.5
23-1014
23-1015
JK1014 1.4
2.2
JK1017 1.7
JK1019 1.9
45 PSI @ 13.5 cfm
45 PSI @ 13.5 cfm
45 PSI @ 13.5 cfm
45-55 PSI @ 9-10.5 cfm
45-55 PSI @ 9-10.5 cfm
45-55 PSI @ 9-10.5 cfm
45-55 PSI @ 9-10.5 cfm
45-55 PSI @ 9-10.5 cfm
45-55 PSI @ 9-10.5 cfm
45-55 PSI @ 9-10.5 cfm



NOZZLE SELECTION CHART
Material ORIFICE SIZE J300H HVLP J300C CONVENTIONAL
45 PSI @ 13.5 cfm
45 PSI @ 13.5 cfm
Sealer 1.4-1.7
Filler 1.7
Primer/ Washprimer/Epoxy 1.4-1.7
Single Stage 1.3-1.4
45 PSI @ 13.5 cfm
45 PSI @ 13.5 cfm
High Solids Clears 1.4-1.5
Basecoat 1.3-1.4
Clearcoat 1.3-1.4