CAMBRIONIX PowerPad16 User manual

User guide V1
PowerPad16

Introduction
The PowerPad16 is a device used to charge 16 USB devices
simultaneously. It's a compact and safe device suited to home
and office use.
The PowerPad16 can be supplied either with or without a power
supply.
Important note:!
If in any doubt about how to operate or install the
PowerPad16 please contact Cambrionix Ltd at
[email protected] !
!

Contents
!
1. Operating
2. Installation
3. Safety messages
4. Electrical specifications
5. Warranty
6. Contact details

1. Operating
• Connect a suitable power cord between the power supply
(PSU) and receptacle (socket outlet). The PSU is shown below.
Power supply for
PowerPad16
Connect a suitably
rated cord between
here and your
receptacle (socket
outlet).
PSU output
connector.

1. Operating
• Connect the output of the power supply to the PowerPad16.
Correctly fitted
power connector.

1. Operating
• Switch the PowerPad16 'on' using the on/off switch as shown
below. The red 'power LED' will illuminate when the PowerPad16 is
switched 'on'.
ON/OFF switch.
Move this slide
switch towards
the power
connector to
switch the
PowerPad16
'ON'.
Power
connector.
Red power
LED.

1. Operating
• Connect your USB devices to the PowerPad16 using suitable USB
cables. These are normally supplied by the USB device manufacturer.
!
!
USB device
cable
connected to
one of the 16
USB ports on
the
PowerPad16.

2. Installation
• The PowerPad16 can either be used on a desk/bench or mounted to a
surface using the mounting holes on either end of the device. Under all
mounting conditions it is essential to avoid covering/blocking the ventilation
holes indicated below.
Ventilation
holes.

2. Installation
• To mount the PowerPad16 to a surface you will require four M5 screws (suitable for
the material you are mounting the PowerPad16 to). You will also require a suitable
tool for driving your chosen screws. Do not use countersunk head screws as these
will damage the plastic flanges, we recommend a 'pan head' screw type.
!
Mounting flange.
There is a flange
on either end of
the PowerPad16.
Holes suitable for
an M5 screw.

2. Installation
• The PowerPad16 dimensions and mounting hole locations are shown below.

2. Installation
• The PowerPad16 can be mounted in a number of vertical orientations as shown below.
The PowerPad16 can also be mounted horizontally to a flat surface such as a desk. Care
should always be taken to ensure that the ventilation holes are not blocked or obstructed.
Vertical surface,
power entry on
right or left.
Vertical surface,
power entry on
top or bottom.

3. Safety messages
• Do not obstruct ventilation holes & slots.
• Do not spill liquids onto the unit.
• Failure to follow operating and installation instructions may result in unit failure.
• Do not attempt to modify or open the PowerPad16 enclosure.
• The plug on the power supply cord is considered the 'disconnect device' and
as such the receptacle (socket outlet) should be located near the PowerPad16
and shall be easily accessible should the power supply need to be isolated
from the 100-240VAC input for whatever reason.
• The power cord should not be attached to a building surface, nor run through
walls, ceilings, floors and similar openings in the building structure.
• When installing the PowerPad16 measures must be taken to avoid physical
damage to the power supply cord, including proper routing of the power supply
cord and provision of a receptacle (socket outlet) near the PowerPad16, or
positioning the PowerPad16 near a receptacle (socket outlet).

4. Electrical specifications of PSU if supplied.
Parameter
Specification
Notes
Part number
FSP180-AHAN1
Manufactured by FSP Group Inc.
PSU input voltage
100-240 VAC
50-60Hz
PSU input current
2.5A
PSU output voltage
12 VDC
PSU output current
15A
Input connector
C14
Output connector
4pin DIN
On the end of a 90cm cable.

4. Electrical specifications of PowerPad16.
Parameter
Specification
Notes
Model number
CBRX1055
Manufactured by Cambrionix Ltd.
Input voltage
12VDC
Input current
15A
Port output voltage
5.2VDC
PSU output current
2.1A
Power in connector
4pin DIN
See product label for pinout.
Output connectors
'USB A' Female
There are 16 output ports.
Operating ambient
35C

5. Warranty
• The PowerPad16 is provided with a 12 month
RTB warranty from date of purchase.
• Details of our standard warranty terms are
available at www.cambrionix.com
!

6. Contact details
• Address: Cambrionix Ltd, St Johns Innovation
Centre, Cowley Road, Cambridge, CB4 0WS,
UK.
• Telephone: [phone]
• Email: suppor[email protected]
• Web: www.cambrionix.com