Campania Triad FT-285 User manual

Tools You Will Need
Level
4mm Allen Wrench
FT-285E
16”x13.5”x15”
107lb
FT-285 Triad Fountain
(5 Pieces)
Components and Parts list
Revised July 11, 2016
FT-285A
29.75”x9”x19.25”
148lb
FT-285B
4”x4”x1”
5lb
FT-285C
30”x20.25”x9”
162lb
FT-285D
1.25”x5.25”x3.75”
2lb
Pump Kit and Parts List
Roughly 12” long 5/8” non-kink hose
Metal hose clamps(3)
300 GPH Pump(1)
Copper spiller (1)
2.8 oz Silicone (1)
Wedges(3)
4mm Allen Wrench (1)
#10 Compression Stopper (1)
This fountain uses
FTNCOV-LRG

Revised July 11, 2016
ASSEMBLY INSTRUCTIONS
1. Make sure you are assembling your fountain on a level surface capable of holding a minimum of
500 pounds with approximately a 5 1/4” square foot footprint.
2. Place the base (FT-285E) into position where the fountain will be installed.
3. Place the basin (FT-285C) centered on top of the base.
4. See enclosed stopper assembly instructions and complete before continuing.
5. Place the hose clamp over the ½” non kink tubing and attach the clamp over the copper piping on
the water feature. Tighten the clamp.
6. Place the water feature (FT-285A) with the ½” non kink tube connected to it over the pump.
7. Attach a hose clamp to the opposite end of the non kink tubing and connect it to the pump.
Tighten the clamp
8. Place the spiller stopper (FT-285B) on top of the water feature. The spiller stopper is to prevent
splashing.
9. Place the copper spiller in the front of the water feature where the water will be spilling out.
10. Fill basin with just enough water to reach the pump cover (approximately 15-20 gallons).
a. Note –do not allow pump to run dry as it will cause damage to the pump.
WINTER CARE AND GENERAL FOUNTAIN INSTRUCTIONS
- W I N T E R C A R E -
Fountain bowls/tops and other fountain components, which collect water, should not be left outside in the
winter since any component, which fills with water and freezes may crack. Likewise components such as
pedestals, which remain in a basin, filled with water, which then freezes, may also crack or crumble.
Ideally, therefore, a fountain should always be stored indoors or in a dry protected place such as a
covered porch away from the elements. However, if a fountain must be left outside:
(1) Remove pump, rubber stoppers, drainpipes, finials, and other small components for storage
indoors. Note that stoppers or drainpipes are removed to allow drainage in the event water accumulates
in any basin. Compression stoppers may be left on the pump cord for easier assembly next season.
(2) Raise fountain base from ground with wood strips so that base will not freeze to the ground
surface.
(3) Cover your Campania Fountain with a Campania Fountain Cover, or wrap the fountain with
burlap or other absorbent material (old blanket or towel) and then cover securely with plastic, making sure
that water will not accumulate in the basin or other fountain component and freeze;
(4) Check fountain periodically to insure that plastic is secure and water is not accumulating in any
fountain component.
- G E N E R A L F O U N T A I N T I P S -
Install fountains on a level surface. You will need a properly grounded 110-volt (AC only) GFCI protected
receptacle near the fountain for your pump. All pumps are submersible and must be completely
underwater to function properly. Test all pumps and adjust to full output prior to assembly. It is not
recommended that fountains be placed directly on grass or dirt. Position the channel opening at the base
of each fountain toward the electrical outlet to be used since the pump cord will
be threaded through this opening.
For more Campania product information visit www.campaniainternational.com
FT-285 Triad Fountain
(5 pieces)
All of our cast stone is proudly