Canon LBP852Cx User manual

USRM2-9945-00 XXXXXXXXXX Copyright CANON INC. 2019 PRINTED IN JAPAN
Getting Started
Quick Operation P.15
Quick Setup NEXT PAGE
Please read "Important Safety Instructions" before operating this product.
After you finish reading this guide, store it in a safe place for future reference.
The information in this document is subject to change without notice.
https://oip.manual.canon/

2
Getting Started
Please read "Important Safety Instructions" before operating this product.
P.20
After you nish reading this guide, store it in a safe place for future reference.
The information in this document is subject to change without notice.
הדובעה תליחת
.הז רצומ תלעפה ינפל "תובושח תוחיטב תוארוה" תא ארק
26 דומע
.ידיתע שומישל חוטב םוקמב ותוא ןסחא ,הז ךירדמ אורקל םייסתש רחאל
.שארמ העדוה לכ אלל יונישל ןותנ הז ךמסמב עיפומש עדימה
You can access
https://oip.manual.canon/ to read the User's Guide that describes all
functions of this machine.
תבותכל סנכיהל ןתינ
לכ תא ראתמש שמתשמל ךירדמה תלבקל https://oip.manual.canon/
.הז רישכמ לש תויצקנופה
Quick Setup

Before starting the installation
• Remove all of the tape.
Installation requirements
Provide a space of 100 mm or more around the
machine.
1075 mm
144 mm556 mm355 mm
55 mm403 mm575 mm
415 mm 585 mm
125 mm
125 mm
325 mm
75 mm
Paper Feeder (Optional)
Toner cartridges and drum cartridges are
included.
× 4
× 4
3
Installation of the Machine
Installing the MachineItems Included with the Machine
Quick Setup

4
5
6
Up to here
1
2
3
4
Installation of the Machine
Quick Setup

7 8Install the paper feeder (optional).
2
1
1
5
Quick Setup

Place horizontally with two or more people.
6
Installation of the Machine
Quick Setup

9Install the cassette feeding unit
(optional).
2
1
1
• Pull out the second paper drawer the same
way.
x 2
7
Quick Setup

Place horizontally with two or more people.
8
Installation of the Machine
Quick Setup

Next, proceed to configure the machine.
Within approx. 80 mm
• Be sure to attach the ferrite core to the
power cord in the position shown in
the illustration.
• When attaching the ferrite core, take
care that the power cord label is not
caught inside the ferrite core.
10
1
2
9
Quick Setup
En
He

Conguring the Method of
Connecting to a Computer
NOTE
Parts and functions of the operation panel.
P.16 "Start the Operation from the Operation
Panel"
1.
2. Configure the initial settings, according to the
screen.
• Set the language and current date/time.
• Set the USB-Connected PC OS.
• Configure the settings to prevent unauthorized
access.
• For the purpose of confirmation, enter the
same PIN twice.
Before starting the configuration
• If the machine is connected to an
unsecured network, your personal
information might be leaked to a third
party. Please be aware and careful of this.
• The machine does not come with a
router. Please have one ready, if necessary.
User's Guide
To connect via wired LAN
The machine does not come with a LAN cable.
Please have one ready, if necessary.
1. Make sure that the computer is connected to a
router properly.
2. Check the network settings on the computer.
3. Connect the LAN cable.
• After connecting the cable, wait a few minutes
(until the IP address is set automatically).
• If a static IP address has been set on the
computer, set the machine's IP address
manually.
4. Install the driver and software.
P.11 "Installing the software"
Now you are finished with the
configuration of the initial settings.
10
Conguring the Machine
Conguring the Initial Settings of
the Machine
Configure the settings in the following order.
Quick Setup
En