Canon BJC-S500 User manual

S500™
Color Bubble Jet™Printer
Quick Start Guide
S500_Front Matter.QXD 5/12/01 1:49 PM Page 1

Canon S500 Color Bubble Jet Printer Quick Start Guide.
CCooppyyrriigghhtt
This manual is copyrighted by Canon U.S.A. Inc. with all rights reserved. Under the copyright laws, this
manual may not be reproduced in any form, in whole or in part, without the prior written consent of Canon
U.S.A. Inc.
© 2001 Canon U.S.A. Inc.
DDiissccllaaiimmeerr
Canon U.S.A. Inc. has reviewed this manual thoroughly in order that it will be an easy to use guide to your
Canon S500 Color Bubble Jet Printer. All statements, technical information and recommendations in this
manual and in any guides or related documents are believed reliable, but the accuracy and completeness
thereof are not guaranteed or warranted, and they are not intended to be, nor should they be understood to
be, representation or warranties concerning the products described.
Specifications are subject to change without notice.
All print speeds based on draft mode. Print speed will vary depending on system configuration, software,
document complexity, print mode and page coverage.
As an Energy Star partner, Canon U.S.A. Inc., has determined that this product meets the
Energy Star guidelines for energy efficiency.
All information regarding non-Canon products was compiled from publicly available information. No
representation is made regarding the accuracy thereof.
TTrraaddeemmaarrkkss
Canon and BJ are registered trademarks and Bubble Jet and S500 are trademarks of Canon Inc.
Canon U.S.A. Inc.
Digital Home and Personal Systems Division
2995 Redhill Avenue
Costa Mesa, CA 92626
PRINTED IN THAILAND
Part number 6861A002AA
S500_Front Matter.QXD 5/12/01 1:49 PM Page 2

CCoonntteennttss
Chapter 1: Basic Printing
Turning Your Printer On and Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
What Is a Printer Driver? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Selecting the S500 Printer for Use . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Recommended Paper Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Loading Paper and Other Media . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Cancelling a Print Job . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Chapter 2: Advanced Print Features
Improving Printed Images . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Adjusting Print Quality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Adjusting Color Balance, Intensity and Brightness . . . . . . . . . . . . . 12
Changing the Page Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Saving and Recalling Driver Settings . . . . . . . . . . . . . . . . . . . . . . . . 17
Chapter 3: Printing Maintenance
Monitoring Ink Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Replacing Ink Tanks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Printing a Nozzle Check Pattern . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Cleaning the Printhead . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Aligning the Printhead . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Chapter 4: Troubleshooting
Tips for Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Customer Care Center . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Chapter 5: The BJ Solution Software–Downloading Images
Minimum System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Installing the BJ Solution Software . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Accessing the Online Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Windows Users: Using Your Software . . . . . . . . . . . . . . . . . . . . . . . . .36
Windows Users: Uninstalling the Software . . . . . . . . . . . . . . . . . . . .38
Macintosh Users: Using Your Software . . . . . . . . . . . . . . . . . . . . . . . .38
Macintosh Users: Uninstalling the Software . . . . . . . . . . . . . . . . . . .40
iii
S500_TOC.QXD 5/12/01 1:51 PM Page iii

Appendix
Installing the Printer Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Uninstalling the Printer Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Registering Your Canon Product . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Regulatory Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Product Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Limited Warranty—U.S. Only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
iv
Contents
S500_TOC.QXD 5/12/01 1:51 PM Page iv

CChhaapptteerr11::BBaassiiccPPrriinnttiinngg
Congratulations on purchasing your new Canon®S500 Color Bubble Jet™
Printer!
With this printer, you can print basic business documents in color or black and
white, as well as print on a variety of specialty media, such as Canon High
Resolution Paper (ideal for business documents such as presentations that
include large numbers of color illustrations), Canon Glossy Photo Paper or
Canon Photo Paper Pro (for digital photographs) and Canon Transparencies (for
presentations). For a full list of the Canon specialty media that can be used with
your S500 printer, see “Specialty Media” on page 3.
This quick start guide describes some of the features of your S500
printer and how to use them. For more information, view and/or
print the S500 User’s Guide on the Setup Software & User’s Guide
CD-ROM.
Driver features and screen shots described in this guide reflect
Windows®98 and may be different for Windows NT®4.0 and
Windows 2000 users.
TTuurrnniinnggYYoouurrPPrriinntteerrOOnnaannddOOffff
To turn your printer on or off, press the
POWER button.
The POWER lamp will flash green when
warming up or when a print job is
being sent to the printer. It will glow a
steady (non-flashing) green when the
printer is ready for use or when the
print job is complete.
If the POWER lamp
flashes orange, see
“Handling Error
Messages” beginning
on page 30.
11
S500_Chapter1.QXD 5/12/01 1:55 PM Page 1

Basic Printing
22
WWhhaattIIssaaPPrriinntteerrDDrriivveerr??
Most computers require special software to link the software applications you
use to create documents or images with your printer. This software, called a
printer driver, converts information from the application into a format that the
printer can understand. The Canon S500 printer driver also provides other
features such as monitoring the printer’s paper supply and ink levels.
SSeelleeccttiinnggtthheeSS550000PPrriinntteerrffoorrUUssee
If the S500 is the only printer connected to your computer, it will automatically
be set as the default (main) printer. However, if your computer has access to
multiple printers, you can set the S500 as the default printer.
TToosseetttthheeSS550000aasstthheeddeeffaauullttpprriinntteerriinnWWiinnddoowwss®::
1. Click SSttaarrtt, then SSeettttiinnggss, then PPrriinntteerrss.
2. Right-click the Canon S500 printer icon, then click SSeettaassDDeeffaauulltt. The Canon
S500 printer icon will display a check mark indicating it is the default
printer.
TToosseelleecctttthheeSS550000ffrroommwwiitthhiinnaaWWiinnddoowwssaapppplliiccaattiioonn::
Even if another printer is set as the default printer, you can still select the Canon
S500 for a specific print job from within most Windows applications.
Menus vary between applications. Consult your application user
documentation if the Print option is not listed.
1. From the FFiilleemenu, click PPrriinntt.
2. Select CCaannoonnSS550000from the Name drop-down list, then click OOKK.
TToosseelleecctttthheeSS550000iinnMMaacc®OOSS::
1. Click AAppppllee, then CChhoooosseerr.
2. Click the SS550000printer icon. The S500 will remain the default printer until
another is selected.
S500_Chapter1.QXD 5/12/01 1:55 PM Page 2

RReeccoommmmeennddeeddPPaappeerrUUssee
There are two steps recommended for getting the best output for your printed
documents:
• Set the printer thickness lever for the media used. (See “Load Limit and
Paper Thickness Lever Position” on page 4.)
• Select the correct media setting in the printer driver. (See “Chapter 2:
Advanced Print Features” on page 9.)
GGeenneerraallBBuussiinneessssPPrriinnttiinngg
For everyday paper printing, use plain paper (17 to 28 lb.). Use standard #10
envelopes with your S500 printer.
SSppeecciiaallttyyMMeeddiiaa
For optimum results, Canon recommends that you use genuine Canon media
with your S500 printer. Follow the instructions that come with any specialty
media on storing, handling and printing.
The specialty media available for use with the S500 include:
• Canon High Resolution Paper
• Canon Transparencies
• Canon Banner Paper
• Canon Glossy Photo Paper
• Canon Photo Paper Pro
• Canon Glossy Photo Cards
• Canon High Gloss Photo Film
• Canon T-Shirt Transfers
For instructions on loading and handling specialty media, see the
instructions that come with that media type or see the S500
User’s Guide on the Setup Software & User’s Guide CD-ROM.
Handle media carefully by its edges. Dirt or fingerprints on the
print surface will adversely affect print quality.
Basic Printing
33
S500_Chapter1.QXD 5/12/01 1:55 PM Page 3

MMeeddiiaattooAAvvooiidd
Do not use the following types of media with your S500 as they could produce
poor quality print images, or jam or damage the printer:
• Paper that is folded, excessively curled, wrinkled or wrapped
• Damp paper
• Excessively thin or thick paper
• Paper with pasted photos, stickers, etc.
• Envelopes with overlapping flaps or self-sealing flaps
• Tractor feed paper, perforated paper or 3-hole punched paper, or paper with
any type of attached fasteners, ribbons, etc.
LLooaaddiinnggPPaappeerraannddOOtthheerrMMeeddiiaa
LLooaaddLLiimmiittaannddPPaappeerrTThhiicckknneessssLLeevveerrPPoossiittiioonn
Basic Printing
44
PPaappeerrTThhiicckknneessss
LLeevveerrPPoossiittiioonn
up to to 100 sheets (17 lbs.)
High Resolution Paper
Photo Paper Pro
Photo Paper Pro (4 x 6)
High Gloss Photo Film
Glossy Photo Paper
Glossy Photo Cards
Transparencies
#10 envelopes
Banner paper
T-Shirt Transfers
MMeeddiiaaTTyyppeePPaappeerrRReessttLLooaaddLLiimmiitt
Plain paper Left
up to 10 sheets Left
up to 80 sheets Left
Left
up to 20 sheets Left
1 sheet
1 sheet Left
up to 20 sheets Left
up to 30 sheets
up to 10 envelopes
1 sheet (print up to 6 connected sheets)
1 sheet
Left
Right
Right
Right
S500_Chapter1.QXD 5/12/01 1:55 PM Page 4

The S500 can print on paper ranging from
standard copier paper (usually 17–28 lb.)
to specialty media paper and envelopes.
The paper thickness lever is located inside
the front cover, on the printhead holder. It
controls the paper feed for the type and
weight of the media on which you are
printing.
For envelopes (see “To load
envelopes:” on page 6), banners and
T-Shirt Transfers.
For regular paper and other media with a left position in the table (see
“Load Limit and Paper Thickness Lever Position” on page 4).
Use the chart on the previous page to ensure that the paper thickness lever is
set correctly for the type of media you are using.
TToollooaaddppaappeerroorrootthheerrmmeeddiiaa::
1. Make sure the paper thickness lever is
set correctly for the media used.
2. Slide the paper guide completely to the left.
3. Fan the edges of the sheets to remove
static cling and avoid paper jams, then
tap the edges of the stack against a flat
surface so the stack is aligned.
4. Insert the media into the paper rest,
with the print side facing up.
Some papers, especially
specialty media, have
specific sides for printing. The print side is usually the glossier
side or the brighter white side. When using specialty media,
do not touch the print side.
5. Slide the paper guide to the edge of the media until it is firmly in place.
You can load up to 100 sheets of plain (17 lb.) paper or 80
sheets of Canon High Resolution Paper in the paper rest at one
time. Never load the paper above the load limit mark.
Basic Printing
55
Print side
Load limit mark
S500_Chapter1.QXD 5/12/01 1:55 PM Page 5

TToollooaaddeennvveellooppeess::
1. Lift the cover and set the paper thickness lever to the envelope mark. Close
the cover.
2. Slide the paper feed guide to the left.
3. Press down on the corners
and sides of the envelopes
to make them as flat as
possible by expelling all of
the air.
To avoid paper jams, make
sure envelopes are flat
before you load them into
the paper tray.
Make sure that none of the flaps overlap. If the envelope
edges are not flat, crease them with the side of a pen.
Do not allow more than 10 envelopes to stack on the paper
output tray.
4. With the address side facing
up and pointed in the
direction shown in the
illustration, align the stack
with the right side of the
paper rest, then insert the
stack into the printer.
5. Slide the paper guide to the
edge of the envelopes until it
is firmly in place.
Basic Printing
66
Flap side of envelope faces down
S500_Chapter1.QXD 5/12/01 1:55 PM Page 6

CCaanncceelllliinnggaaPPrriinnttJJoobb
There are several ways to cancel a print job in progress:
TTooccaanncceellaapprriinnttjjoobbffrroommtthheepprriinntteerr::
While a job is printing, press the RREESSUUMMEE//CCAANNCCEELL
button on the printer. The print job will be cancelled
and the paper ejected.
TTooccaanncceellaapprriinnttjjoobbffrroommtthheeSS550000pprriinntt
ddiiaallooggbbooxx::
When a job is printing on the S500, a print status
dialog box displays on your screen.
Click CCaanncceellat any time while this dialog box is
open to cancel the current print job. The print job
will be cancelled and the paper ejected.
TTooccaanncceellaapprriinnttjjoobbffrroommtthheePPrriinntteerrSSttaattuussMMoonniittoorr::
1. Click SSttaarrtt, then SSeettttiinnggss, then PPrriinntteerrss.
2. Right-click CCaannoonnSS550000, then click
PPrrooppeerrttiieess.
3. Select the MMaaiinntteennaanncceetab, then click the
SSttaarrttSSttaattuussMMoonniittoorrbutton.
4. Click CCaanncceellPPrriinnttiinngg.
The print job will be cancelled and the paper
ejected.
TTooccaanncceellaapprriinnttjjoobbffrroommWWiinnddoowwss::
1. Click SSttaarrtt, then SSeettttiinnggss, then PPrriinntteerrss.
2. Double-click CCaannoonnSS550000,,click the print job, then press the DDeelleetteekey.
The print job will be cancelled and the paper ejected.
Basic Printing
77
RESUME/CANCEL button
S500_Chapter1.QXD 5/12/01 1:55 PM Page 7

TTooccaanncceellaapprriinnttjjoobbiinnMMaaccOOSSwwhheennuussiinnggffoorreeggrroouunnddpprriinnttiinngg::
On your keyboard, press the Apple™CCoommmmaannddkey ( ) and the period key ( . )
at the same time.
The print job will be cancelled and the paper ejected.
TTooccaanncceellaapprriinnttjjoobbiinnMMaaccOOSSwwhheennuussiinnggbbaacckkggrroouunnddpprriinnttiinngg::
1. While a job is printing, go
to the BJ Print Monitor
window (click FFiinnddeerr, then
BBJJPPrriinnttMMoonniittoorr).
2. Highlight the job to be
cancelled.
3. Click the SSttooppPPrriinnttiinnggicon
in the Print Queue dialog
box.
The print job will be cancelled
and the paper ejected.
Basic Printing
88
S500_Chapter1.QXD 5/12/01 1:55 PM Page 8

CChhaapptteerr22::AAddvvaanncceeddPPrriinntt
FFeeaattuurreess
IImmpprroovviinnggPPrriinntteeddIImmaaggeess
Two important factors control the quality and output of your printed images:
PPaappeerraannddIInnkkUsing recommended paper or specialty media for printing
graphic images or photographs can significantly improve the quality of your
printout. (See “Recommended Paper Use” on page 3.) Also, always use the
specific Canon inks for your S500 printer, as noted on the inside back cover.
PPrriinntteerrDDrriivveerrSSeettttiinnggssThere is a variety of settings you can use to enhance
the quality of the print, the colors and the way in which the document
comes out of the printer.
Many of these features are covered in this chapter. For more
information, see the S500 User’s Guide on the Setup Software
& User’s Guide CD-ROM, or access the online help:
While in the Properties window, press the FF11key, or click in
the upper right corner then click the feature you want to know
more about, or click the button when displayed.
Turn Bubble Help on by selecting HHeellpp, then SShhoowwBBuubbbbllee
HHeellpp.
AAddjjuussttiinnggPPrriinnttQQuuaalliittyy
Two of the features that affect the appearance and quality of your printed
documents can be controlled with the printer driver.
MMeeddiiaaTTyyppeeThe S500 automatically adjusts printer settings to improve
print quality based on the media type (plain paper, Glossy Photo Paper, etc.)
you select.
PPrriinnttQQuuaalliittyyWhen you select a media type, print quality is automatically
set for that media. You can change print quality settings if desired.
99
S500_Chapter 2.QXD 5/12/01 1:53 PM Page 9

Advanced Print Features
1100
TToommaannuuaallllyyaaddjjuussttpprriinnttqquuaalliittyysseettttiinnggssiinnWWiinnddoowwss::
1. From an application FFiilleemenu, select PPrriinntt.
2. With CCaannoonnSS550000as the selected printer, click PPrrooppeerrttiieess. The S500
Properties window will open to the Main tab.
3. Select the appropriate MMeeddiiaa
TTyyppeefrom the drop-down
menu.
4. Each media type has a default
quality, but you can select a
different PPrriinnttQQuuaalliittyy:
HHiigghhFor high quality when
printing a color document.
SSttaannddaarrddFor high quality
when printing text.
DDrraaffttFor printing text drafts
at a faster speed.
CCuussttoommAllows for more precise control.
If you select CCuussttoomm, the Set button becomes active. Click SSeettto open the
Set Print Quality dialog box. There are two features you can control:
PPrriinnttQQuuaalliittyyThe printer driver
provides five settings for custom
print quality, ranging from FFaasstt
at the far left (prints at 600 dpi,
which means faster printing and
less ink) to FFiinnee, which prints at
2400 x 1200 dpi.
HHaallffttoonniinnggThis controls the
pattern in which the ink is laid
down during printing for
graphic images.
5. When done, click OOKK.
S500_Chapter 2.QXD 5/12/01 1:53 PM Page 10

TToommaannuuaallllyyaaddjjuussttpprriinnttqquuaalliittyy
sseettttiinnggssiinnMMaaccOOSS::
1. Make sure that the SS550000is the
selected printer (from the AAppppllee
menu, select CChhoooosseerr, then SS550000).
2. From an application FFiilleemenu, click
PPrriinntt.
3. Click the MMaannuuaallprint mode icon,
then click the DDeettaaiillssbutton. The
Detailed Setting dialog box will open.
Make sure QQuuaalliittyyis selected.
4. Click and drag the PPrriinnttQQuuaalliittyyslide
bar to select your preferred output
quality.
5. When done, click OOKK, then PPrriinntt.
TToosseelleeccttbbeessttpprriinnttqquuaalliittyywwiitthhtthheePPrriinnttAAddvviissoorrwwiizzaarrdd::
Print Advisor is a wizard that helps you select the most optimum media type and
print quality for your print job.
1. From an application FFiillee
menu, select PPrriinntt.
2. With CCaannoonnSS550000as the
selected printer, click
PPrrooppeerrttiieess. The S500
Properties window will open
to the Main tab.
3. Click the PPrriinnttAAddvviissoorrbutton.
The wizard dialog box will
open.
4. Follow the on-screen
instructions to select the
optimum output type, media
and settings for your print job.
5. Click OOKKto save the setting and close the S500 Properties window.
Advanced Print Features
1111
S500_Chapter 2.QXD 5/12/01 1:53 PM Page 11

TTooaauuttoommaattiiccaallllyymmaakkeeiimmaaggeessmmoorreessmmooootthhiinnWWiinnddoowwss::
Image Optimizer smoothes jagged edges formed when enlarging a photo or
graphic from its original size. It is most effective when used with low-resolution
images.
1. From an application FFiilleemenu,
select PPrriinntt.
2. With CCaannoonnSS550000as the
selected printer, click
PPrrooppeerrttiieess.
3. Click the EEffffeeccttsstab, then click
the IImmaaggeeOOppttiimmiizzeerrcheck box.
4. Click OOKKto save this setting
and close the S500 Properties
window.
AAddjjuussttiinnggCCoolloorrBBaallaannccee,,IInntteennssiittyyaannddBBrriigghhttnneessss
You can enhance color printing by adjusting the color balance, intensity
(saturation) and brightness.
For more information on these settings, see the S500 User’s Guide
on the Setup Software & User’s Guide CD-ROM, or access the
online help (press FF11or click in Windows; turn on Bubble Help in
Mac) while in the printer driver interface.
TToommaannuuaallllyyaaddjjuussttccoolloorr
sseettttiinnggssiinnWWiinnddoowwss::
1. From an application FFiilleemenu,
select PPrriinntt.
2. With CCaannoonnSS550000as the
selected printer, click PPrrooppeerrttiieess.
3. On the MMaaiinntab, under CCoolloorr
AAddjjuussttmmeenntt, select MMaannuuaall.
The Set button will become active.
4. Click SSeett, and the Manual
Color Adjustment dialog box
will open.
Advanced Print Features
1122
S500_Chapter 2.QXD 5/12/01 1:53 PM Page 12

5. Click and drag the CCoolloorrBBaallaanncceeslide
bar for each color to adjust the color
settings. The results will preview.
6. Click and drag the IInntteennssiittyyslide bar to
change the intensity (saturation) for the
image. The results will preview.
7. IImmaaggeeCCoolloorrMMaannaaggeemmeenntt((IICCMM))is a
feature that automatically adjusts the
image colors. (This feature is only available in Windows 98, Me and 2000).
To use ICM for automatic color adjustment, click the EEnnaabbllee
IICCMMcheck box. All other features on this tab (except Intensity)
will become inactive.
8. Under PPrriinnttTTyyppee, select PPhhoottoowhen printing photographs. This allows for a
wider range of tones. Set to GGrraapphhiiccwhen printing graphic images for
crisper, cleaner graphic images.
9. Select a BBrriigghhttnneesssssetting to determine how light or dark the image will
appear when printed.
10. When done, click OOKK.
To print in black only, check the GGrraayyssccaalleePPrriinnttiinnggbox. This
will convert color images to grayscale when printing, without
changing the original colors in the document.
TToommaannuuaallllyyaaddjjuussttccoolloorrsseettttiinnggssiinnMMaaccOOSS::
1. Make sure that the SS550000is the selected printer. (From the AApppplleemenu,
select CChhoooosseerr, then SS550000.)
2. From an application FFiilleemenu, click PPrriinntt.
3. Click the MMaannuuaallprint mode icon,
then click DDeettaaiillss.
4. Click the CCoolloorricon.
5. Adjust the CCoolloorrCCoorrrreeccttiioonn, PPrriinntt
TTyyppee, GGaammmmaaCCoorrrreeccttiioonn, CCoolloorr
BBaallaanncceeand IInntteennssiittyysettings for
your image.
6. When done, click OOKK, then PPrriinntt.
Advanced Print Features
1133
S500_Chapter 2.QXD 5/12/01 1:54 PM Page 13

TTooaauuttoommaattiiccaallllyyooppttiimmiizzeetthheeiimmaaggeeiinnWWiinnddoowwss::
Photo Optimizer PRO automatically adjusts a photographic image created with a
digital camera. Use this feature to compensate for unsatisfactory color balance and
over- or under-exposure before printing.
1. From an application FFiilleemenu, select PPrriinntt.
2. With CCaannoonnSS550000as the selected printer, click PPrrooppeerrttiieess.
3. Select the EEffffeeccttsstab.
4. Click to check the PPhhoottoo
OOppttiimmiizzeerrPPRROOcheck box.
When PPhhoottooOOppttiimmiizzeerrPPRROO
is checked, the AAppppllyy
TThhrroouugghhoouuttPPaaggeeoption
becomes active. If this box is
left unchecked, the S500 will
optimize each image
individually. If checked, all
images will be automatically
corrected with the same
settings.
5. When done, click OOKK.
CChhaannggiinnggtthheePPaaggeeSSeettuupp
You can change how the image is printed without affecting the original image
file.
TToocchhaannggeeppaaggeesseettuuppiinnWWiinnddoowwss::
1. From an application FFiilleemenu, select PPrriinntt.
2. With CCaannoonnSS550000as the selected printer, click PPrrooppeerrttiieess.
3. Click the PPaaggeeSSeettuupptab.
4. From this tab, you can change the following options:
PPaaggeeSSiizzeeDefaults to the page size set in the original document, but can
be changed.
OOrriieennttaattiioonnLets you select either portrait or landscape orientation.
Advanced Print Features
1144
S500_Chapter 2.QXD 5/12/01 1:54 PM Page 14