Casall INF 2.0 PLUS User manual

CasallINF 2.0 PLUS
Bike
91032

Important: Please locate your serial number and record in the box below for service
support purposes.
Serial number here:

Serial number

INF 2.0 PLUS
No:J-7 Screw M3*14L (2)
No:J-6 C-shape knob M7*65L (1)
No:J-4 Spring Washer
Ø7*2t(2)
No:J-2 Allen Bolt
M7*P1.0*30L (1)
No:J-8 Metal cover (1)
No:J-5 Bushing Ø 12*40L (1)
No:J-3 Regular Washer
Ø7*1t(2)
No:J-1 allen bolt M8*16L (4)
Screwdriver (1)
(Pedal Wrench)
Socket Wrench(1)
Allen Key(1)

EXPLODED DIAGRAM

PARTS LIST
NO. Description Specifications Q'TY
A-1,A-2 COMPUTER & SCREW 1SET
B HANDLEBAR 1 PC
B-1 CAP FOR HANDBLEBAR 2 PC
B-2 FOAM GRIP 2 PC
B-3 ELBOW HOLDER (R) 1PC
B-4 HAND PULSE SET W/WIRE 1SET
B-5 ELBOW HOLDER (L) 1PC
C-1 HANDLEBAR POST 1 PC
C-2 COMPUTER CABLE (UPPER) 1 PC
C-3 BOTTLE HOLDER 1 PC
C-4 SCREW FOR F/R COVER M5xP0.8x14L 2 PC
C-5 REAR COVER FOR COMPUTER 1 PC
C-6 FRONT COVER FOR COMPUTER 1 PC
C-7 SCREW FOR BOTTLE HOLDER M5x20L 2 PC
D-1 MAIN FRAME 1 PC
D-3 ALLEN BOLT FOR HANDLEBAR POST M8x16 4 PC
D-4 FLAT WASHER φ12xφ19x1t 4 PC
D-5 ADJUSTING KNOB FOR MAIN FRAME 1 PC
D-6 BELT J6 1016m/m 1 PC
D-7 BIG PULLEY 1 PC
D-8 SHAFT 1 PC
D-9 SCREW M8xP1.25x12Lx5t 3 PC
D-10 FLAT WASHER φ17.5xφ25x0.3t 2 PC
D-11 Wave WASHER φ17.5xφ25x0.3t 1 PC
C-12 C-TYPE RING φ17 1 PC
D-13 BEARING 6203 (RS) 2 PC
D-14 PLASTIC BUSHING 1 PC
D-15 SENSOR BOX 1 PC
D-16 SCREW FOR SENSOR BOX M4x10L 1 PC
D-17 SCREW FOR CHAIN COVER M5x16L 4 PC
D-18 SCREW FOR CHAIN COVER M4x50L 5 PC
D-19 CHAIN COVER (L) 1 PC
D-20 CHAIN COVER ( R) 1 PC
D-21 CROSS DISC (R ) 1 PC
D-22 ROUND DISC 2 PC
D-23 NUT FOR DISC M10xP1.25x10T 2 PC
D-24 CAP FOR ROUND DISC 2 PC
D-25 SCREW FOR DISC M4x14L 8 PC

D-26 FLAT WASHER φ15xφ16x1t 8 PC
D-27 CROSS DISC (L) 1PC
D-28 CAP FOR CHAIN COVER SCREW HOLES OVAL 4 PC
D-29 CAP FOR CHAIN COVER SCREW HOLES ROUND 5 PC
D-30 COVER FOR HANDLEBAR POST 1 PC
D-31 SPRING RING 2 PC
D-32 BUSHING φ22xφ17x7.5mm 1 PC
D-33 DC CABEL 1 PC
E-1~E-14 FLYWHEEL SET 1SET
F-1 FRONT STABILIZER 1 PC
F-2 LEFT CAP FOR FRONT STABILIZER 1 PC
F-3 RIGHT CAP FOR FRONT STABILIZER 1 PC
F-4 SCREW M5x16L 2 PC
F-5 ADJUSTING PAD FOR R/L STABILIZER 4 PC
F-6 REAR STABILIZER 1 PC
F-7 SCREW 3/16”x11/8” 2 PC
F-8 CAP FOR REAR STABILIZER 2 PC
G-1 SEAT POST SET 1 SET
G-2~G-6 SEAT SLIDER 1SET
G-7 SEAT 1 PC
H-RL PEDAL 1SET
I-1~I-8 IDLER WHEEL.SET 1SET
J-1~J-8 BOLT & NUT PACK 1 SET
K~K-12 MAGNETIC SET 1 SET
K-13,D-2 GEAR BOX SET 1 SET
L ADAPTOR 1 PC

Step 1 Foot Tube Assembly
Attach the Front Stabilizer (F-1) to the Main Frame (D-1) using two M8x16 Allen bolt (J-1)
Attach the Rear Stabilizer (F-6) to the Main Frame (D-1) using two M8x16 Allen bolt (J-1).
Step 2 Pedal Assembly
1. Assemble the two Pedals (H-R+L) onto the Cross disc (D-21 + D-27) with a screw driver.
Remarks: Screw the left pedal’s spindle counter-clockwise and the right pedal’s spindle clockwise.
Use a wrench (or screwdriver) to screw the two spindles completely.
M8*16L 1*
D-1
F-6
D-1
4*
1*

Step 3 --Seat Tube Assembly
1. Assemble the seat (G-7) to the Slider. The Slider can be adjusted in different angles. Tighten the
two Nuts under the Seat using a screwdriver. In addition, the Slider can be adjusted in horizontal
level by loosing the Knob.
2. Insert the seat post (G-1) into the main frame (D-1), then choose the desired position and tighten
the knob. Be sure the knob is always tightened.
Remarks: When you have chosen a desired position, tighten the Seat Post Knob until you hear a
“click”.
M16
1*
D-1

Step 4-Handlebar post Assembly
1. Please remove the M8x16 Allen bolt (D-3) and flat washers (D-4) from the main frame (D-1)
2. Take the Handlebar post cover (D-30) and pass it through Handlebar post (C-1)
3. Hold the Handlebar post (C-1) and connect the Lower computer cable (D-2) to the Upper
computer cable (pt. C-2)
4. Slide the Handlebar Post (pt.C-1) into the Main frame then fix it with four sets of M8X16 Allen
screws (D-3) and Flat washers (pt.D-4)..
Remarks: Do not screw one set of the M8X16 Allen Screws and Flat washers too firm at one time. It
is better to fix the four sets firmly at the same time because it helps you to change angles and to fix
easily.
4* M8*16L Ø12*1T 1*
D-1

Step 5- Handlebar and Computer Assembly
1. Attach the Handlebar (B) to the Handlebar post (C-1) using the clamp (J-8). Fix firmly with one
Flat washers (J-3), one Spring washer (J-4) and one Fixing bolt (J-2).
2. Pass the hand-pulse wire (B-4) through the hole.
3. Connect the Computer cables (C-2) and hand pulse wire (B-4). Then attach the Computer (A-1)
to the Computer bracket with the enclosed Screws (A-2).
Ø7*2T
Ø7*1T M7*30L
4* M5*10L 1*
1*
比例25.400
B-4