Casall INF 2.0 PLUS User manual

1
Casall INF 2.0 PLUS
CROSSTRAINER
93017

2
Important: Please locate your serial number and record in the box below for service
support purposes.
Serial number here:



3
Screw
M3x14L (2)
Allen bolt M8x30L (2) Flat Washer Ø8xØ16x1t (4) Allen Bolt M8x55 (2)
Screw M3x25L (8)
Allen bolt M8x12L (8)
Allen Bolt M7*P1.0*30L (2)
P-1
Flat washer
Ø7x1t (2)
P-2
Metal cover (1)
P-3
Spring washer
Ø7x2t (2)
P-4
P-5
P-6
P-8
P-10
Steel washer（2）
P-11
Flat washer Ø8xØ25x2t (2)
P-12
P-13
P-15 P-14
Allen bolt M8x16L (4)
P-7
Nut M8 (2)
P-9
93017 INF2.0 plus
Wave washer Ø20xØ30x0.3t

4
Knob M6*P1.0 (4)
Spring washer Ø6 (4) Carrage bolt M6*P1.0*40L (4)
P-16
Bushing (4)
P-18
P-17 P-19
Allen Key(2)
Box Spanner (1)
93017 INF2.0 plus

5
EXPLODED DIAGRAM
H-8

6
PARTS LIST
No. Item spec. Q'ty
A , A-1 Computer & Screw for computer 1SET
B-1 Front handlebar 1PC
B-2 Foam grip for front handlebar 2PCS
B-3 End cap for foam grip φ7/8" 2PCS
B-4 Hand pulse WP1007-33B 1SET
B-5 Screw M3x20L 2 PCS
B-6 Wire for hand pulse 1 PC
C-1 Upper handlebar ( L) 1SET
C-2 End cap for upper handlebar (R&L) φ1 1/4" 2PCS
C-3 Foam grip for upper handlebar 2PCS
C-4 Upper handlebar ( R) 1PC
D-1 Handlebar post 1PC
D-2 Upper computer cable 1PC
D-3 Screw for computer cover M5x14L 2PCS
D-4 Bushing 2PCS
D-5 Allen bolt M8x16 4PCS
D-6 Flat washer φ12xφ19x1t 4PCS
D-7 Screw for bottle holder M5x20L 4PCS
E-1~E7 First-lower handlebar (R& L) 1SET
F-1 Main frame 1SET
F-2 C-type ring φ12 1PC
F-3 Wave washer φ20xφ30x0.3t 1PC
F-4 Flat washer φ20.3xφ30x1t 1PC
F-5 Sensor box 1PC
F-6 Sensor holder 1PC
F-7 DC cable 1PC
F-8 Screw M4x10L 1PC
F-9 Bearing 6004RS 2PC
G1~G-8 Flywheel set 1SET
H Magnetic set & Gear box 1SET
I-1 Pedal post (Left) 1PC
I-2 Screw M5x14L 4PC
I-3 Pedal post (Right) 1PC
J-1~J-3 Front stabilizer set 1SET
K-1~K-3 Rear stabilizer set 1SET

7
L-1~L-11 Idler wheel set 1SET
M-1 Front cover for computer 1PC
M-2 Rear cover for computer 1PC
M-3 Bottle holder 1PC
M-4 Front cover (Left) for pedal post 2PCS
M-5 Front cover (Right) for pedal post 2PCS
M-6 Pedal (Left) 1PC
M-7,M8 Left rear cover (upper/down) for pedal post 1SET
M-9 Pedal (Right) 1PC
M-10,M-11 Right rear cover (upper/down) for pedal post 1SET
M-12 Screw for chain cover M4x50L 5PCS
M-13 Screw for chain cover M5x16L 6PCS
M-14 Left chain cover 1PC
M-15 Right chain cover 1PC
M-16 Cap for chain cover screw holes Oval 5PC
M-17 Cap for chain cover screw holes Round 4PC
M-18 Cover for handlebar post 1PC
M-19 Axle for first-lower handlebar 1PC
N Adaptor 1PC
P-1~P-19 Bolts & nuts pack 1SET
Q-1 Shaft 1PC
Q-2 Bushing φ20.5xφ25x7.5mmL 1PC
Q-3 Hexagonal screws M8xP1.25x12Lx5t 3PCS
Q-4 Big pulley 1PC
Q-5 Belt J6 1219m/m 1PC
R-1 Nut M10xP1.25x10T 2PC
R-2 Cross disc 2PCS
R-3 Round disc 2PCS
R-4 Screw M4x14L 8PCS
R-5 Flat washer φ5xφ16x1t 9PCS
R-6 Cap for round disc 2PCS
S-1~S-8 Crank connation set 2SET

8
ASSEMBLY STEPS
STEP 1
Attach the Front Stabilizer (J-1) to the Main Frame (F-1) using two Allen bolt (P-7) Attach the Rear
Stabilizer (K-1) to the Main Frame (F-1) using two Allen bolt (P-7).
.
STEP 2
1. Please remove four sets of the M8x16 Allen bolt (D-5) and Flat Washer (D-6)from the Main
Frame (F-1)
2. Take the Handlebar post (D-1) and pass it through the Handlebar post cover (M-18).
3. Hold the Handlebar Post (D-1) and connect the Lower Computer Cable (H-14) and the Upper
Computer Cable (D-2)
4. Slide the Handlebar Post (D-1) into the Main Frame then fix with four sets of M8x16
Allen bolt (D-5) and Flat Washers (D-6).
M8*16L
4* 1*
K-1
4* 1*
Ø12*Ø19*1T M8*16L

9
STEP 3
1. Attach the Front handlebar (B-1) to the Handlebar post (D-1) using the clamp cover (P-3), and
then fix with two Flat Washers (P-2), two Spring Washers (P-4), two Fixing Bolt (P-1).
2. Pass the hand-pulse wire (B-6) through the hole.
3. Connect the Computer cables (D-2) and connect the Hand pulse wire (pt.B-6), then attach the
Computer (A-1) to the Computer bracket with the enclosed Screws (A-2).
STEP 4
1. Remove the pre-installed Screws (D-3) on the handlebar post first.
2. Attach the Rear cover (M-2) using two of Screws (P-6) and one of Screws (D-3) .
3. Attach the Front cover (M-1) using Screws (D-3)
4. Remove the pre-installed Screws (D-7) on the handlebar post, and then assemble the Bottle
holder (M-3) by Screw (D-7).
2x
Ø7x2T
Ø7x1T M7x30
M5x10
4x 1x
1x
比例25.400
4x
1x
M5x14
2x M5x20
2x

10
STEP 5 Fix the two Lower handlebar (E-1) to the Handlebar Post (D-1) with one Axle (M-19),
two sets of Wave washer (P-13), Flat washers (P-12) and Gasket (P-11) and Allen
bolt (P-10).
Pay attention : Please use two allen key tools to fix bolt (P-10) on both side at the same time.
STEP 6
1. Attach the Left and Right lower Handlebar (E-1 L/R) to the Left and Right pedal post (I-1
& I-3) using two Allen bolt (P-14), four Flat washers (pt.P-15) and two Nylon nuts (P-9). ---
Figure A
2. Attach the Pedal post (I-1 & I-3) onto the Crank connation set using one of Nylon nuts (S-4),
Flat washers (S-3) and Plastic washers (S-8). --- Figure B
3. Connect the Right rear cover (upper) (pt.M-8) and Right rear cover (lower) (pt.M-7) to the Left
pedal post (I-1) using screw (P-5). --- Figure C
4. Connect the Left rear cover (upper) (M-10) and Left rear cover (lower) (M-11) to the Right pedal
post (I-3) Using screw (P-5).
C
D
M8*55
M3*25L
M8
M8
2*
4*
6*
1*
AB
Steel washer
2x
1x
Ø20xØ30x0.3t
Ø8xØ25x2t

11
STEP 7
1. Remove the pre-installed screws (I-2) on the Pedal post first.
2. Attach the Lower handlebar (E-1 R/L) to the left and right pedal post (I-1), and then close the
cover (M-4 & M-5) using screws (P-5 & I-2).
3. Assemble the Right pedal (M-9) onto the Pedal post (I-3) with 2 Knobs (P-16), 2 Spring
washers (P-18),2 Bushings (P-19) and 2 Carriage bolts (P-17).
4. Assemble the Left pedal (M-6) onto the Pedal post (-3) with 2 Knob (P-16), 2 Spring washers
(P-18),2 Bushings (P-19) and 2 Carriage bolts (P-17).
`
STEP 8 Slide the Upper handlebar post (C-1,C-4) (R/L) into the Lower handlebar (E-1) and then
fix with the eight Allen bolts (P-8)
M5*14
M3*25L
M6*P1.0*40L M6
4* 2* 4* 1*
Ø6Ø7*Ø12*25
E-1
M8x12L
8x
1x

12
STEP 9
Connect the adaptor (N) to the DC hole (located on the back of the chain cover).
FithiwayAppINSTRUCTIONMANUAL
比例25.400
System plug connection socket
Hand pulse socket

13
DISPLAY FUNCTIONS
ITEM DESCRIPTION
TIME Count up - No preset target, Time will count up from 00:00 to maximum 99:59 with
each increment is 1 minute.
Count down - If training with preset Time, Time will count down from preset to 00:00.
Each preset increment or decrement is 1 minute between 00:00 to 99:00.
SPEED Displays current training speed. Maximum speed is 99.9 KM/H or ML/H.
RPM Displays the Rotation Per Minute. Display range 0~15~999
DISTANCE Accumulates total distance from 0.00 up to 99.99 KM or ML. The user may preset
target distance data by using UP/DOWN button.
Each preset increment or decrement is 0.1KM or ML between 0.00 to 99.90.
CALORIES Accumulates calories consumption during training from 0 to maximum 9999
calories.
(This data is a rough guide for comparison of different exercise sessions which can
not be used in medical treatment.)
PULSE User may set up target pulse from 0 - 30 to 230; and computer buzzer will beep
when actual heart rate is over the target value during workout.
WATTS Display current workout watts. Display range 0~999.
MANUAL Manual mode workout.
BEGINNER 4 PROGRAM selection.
ADVANCE 4 PROGRAM selection.
SPORTY 4 PROGRAM selection.
CARDIO Target HR training mode.
WATT
PROGRAM WATT constant training mode.
KEY FUNCTION
PS. According to different console design, not all consoles have total reset function key.
ITEM DESCRIPTION
Up (Encoder) Increase resistance level
Setting selection.
Down (Encoder) Decrease resistance level
Setting selection.
Mode / Enter Confirm setting or selection.
Reset Press and hold for 2 seconds, computer will reboot and start from user setting.
Reverse to main menu during preset workout value or stop mode.
Start/ Stop Start or Stop workout.
Recovery Test heart rate recovery status.

14
OPERATION:
POWER ON
Plug in power supply, computer will power on and display all segments on LCD for 2 seconds
(Drawing 1).
Drawing 1
WORKOUT SELECTION
Use UP or DOWN (Encoder) to select workout Manual (Drawing 2)Beginner(Drawing 3) 
Advance (Drawing 4) Sporty(Drawing 5) Cardio(Drawing 6) Watt(Drawing 7).
Drawing 2 Drawing 3
Drawing 4 Drawing 5
Drawing 6 Drawing 7
Manual Mode
Press START in main menu may start workout in manual mode.
1. Use UP or DOWN (Encoder) to select workout program, choose Manual and press MODE /
ENTER to get into.
2. Use UP or DOWN (Encoder) to set TIME (Drawing 8), DISTANCE (Drawing 9), CALORIES
(Drawing 10), PULSE (Drawing 11) and press MODE / ENTER to confirm.
3. Press START/STOP keys to start workout. Use UP or DOWN (Encoder) to adjust load level.
Load level display in WATT window, no adjusting for 3s, it will switch to display WATT (Drawing
12).
4. Press START/STOP keys to pause workout. Press RESET to reverse to main menu.

15
Drawing 8 Drawing 9
Drawing 10 Drawing 11
Drawing 12
Beginner Mode
1. Use UP or DOWN (Encoder) to select workout program, choose Beginner mode and press
MODE / ENTER to get into.
2. Use UP or DOWN (Encoder) to select Beginner program 1~4 (Drawing 13) and press MODE /
ENTER to get into.
3. Use UP or DOWN (Encoder) to set TIME.
4. Press START/STOP key to start workout. Use UP or DOWN (Encoder) to adjust load level.
5. Press START/STOP key to pause workout. Use RESET to reverse to main menu.
Drawing 13
Advance Mode
1. Use UP or DOWN (Encoder) to select workout program, choose Advance mode and press MODE
/ ENTER to get into.
2. Use UP or DOWN (Encoder) to select Advance program 1~4 (Drawing 14) and press MODE /
ENTER to get into.
3. Use UP or DOWN (Encoder) to set TIME.
4. Press START/STOP key to start workout. Use UP or DOWN (Encoder) to adjust load level.
5. Press START/STOP key to pause workout. Use RESET to reverse to main menu.

16
Drawing 14
Sporty Mode
1. Use UP or DOWN (Encoder) to select workout program, choose Sporty mode and press MODE /
ENTER to get into.
2. Use UP or DOWN (Encoder) to select Sporty program 1~4 (Drawing 15) and press MODE /
ENTER to get into.
3. Use UP or DOWN (Encoder) to set TIME.
4. Press START/STOP key to start workout. Use UP or DOWN (Encoder) to adjust load level.
5. Press START/STOP key to pause workout. Use RESET to reverse to main menu.
Drawing 15
Cardio Mode
1. Use UP or DOWN (Encoder) to select workout program, choose H.R.C. and press MODE /
ENTER to get into.
2. Use UP or DOWN (Encoder) to set Age (Drawing 16).
3. Use UP or DOWN (Encoder) to select 55% (Drawing 17).75%.90% or TAG (TARGET H.R.)
(default: 100).
4. Use UP or DOWN (Encoder) to set workout TIME.
5. Press START/STOP key to start or stop workout. Use RESET to reverse to main menu.
Drawing 16 Drawing 17
Watt Mode
1. Use UP or DOWN (Encoder) to select workout program, choose WATT and press MODE /
ENTER to get into.
2. Use UP or DOWN (Encoder) to set WATT target. (default: 120, Drawing 18)
3. Use UP or DOWN (Encoder) to set TIME.
4. Press START/STOP key to start workout. Use UP or DOWN (Encoder) to adjust Watt level.
5. Press START/STOP key to pause workout. Use RESET to reverse to main menu.

17
Drawing 18
Measuring your pulse with the hand sensors
The hand sensor are not medical products, but rather exercising tools designed for the approxl-mate
measurement and displaying of the pulse rate when exercising with the exercise bike.
RECOVERY
After exercising for a period, keep holding on hand grips or wearing chest strap and press
RECOVERY key. All function display will stop except “TIME” starts counting down from 00:60 to
00:00 (Drawing 19). Screen will display your heart rate recovery status with the F1, F2…. to F6. F1 is
the best, F6 is the worst (Drawing 20). User may keep exercising to improve the heart rate recovery
status. (Press the RECOVERY button again to return the main display.)
Drawing 19 Drawing 20
Noted:
1. After 4 minutes without pedaling or pulse input, console will enter into power saving mode. Press
any key may wake the console up.
2. When computer act abnormal, please plug out the adaptor and plug in again.
Fit Hi Way APP
The console has been built-in 4.0 Bluetooth module for APP function. User can connect console to
tablet or smart phone for APP function through Bluetooth.
First, search letters [Fit Hi Way] App on APP store or Google Play Assistant, download the APP and
install it to mobile device.
Then, turn on Bluetooth on tablet, search for console device and press connect.
Pair tablet and console thru BT. Turn on [Fit Hi Way] APP on tablet and start workout with tablet.
(APP operation refer to Fit Hi Way Instruction Manual)
You can measure your pulse with the two
hand sensor on the handle.
>> Place both hands on the hand sensor on
the handle as you exercise and wait briefly
for the pulse value to be displayed.
Hand sensor
for pulse measurement

18
NOTE:
1. Once console is connected to tablet via Bluetooth, the console will power off.
2. Please exit Fit Hi Way app and turn off the Bluetooth from the smart device, then the console will
power on again.
3. If console operation or display abnormally, please Power-off and restart it.
The manual will be updated from time to time, the consumer can get the newest version by
scanning the QR code or link to the website as below.
https://drive.google.com/drive/folders/0B_a5atcMnWbpbWwyMll0VDFqNzQ
Fit Hi Way INSTRUCTION :
Attention! All preset data will be lost when unplug the power (adaptor)
from the "machine".
