Case IH SPX 320 User manual

Case IH SPX 320 Closed Center
Supplement & Installation Manual
P/N 016-0190-034 Rev D 09/15
Copyright 2006, 2015

RavenIndustries
FlowControls Division
P.O.Box 5107
Sioux Falls, SD 57117-5107
TollFree 800-243-5435
Fax[phone]
www.ravenprecision.com
[email protected]
DISCLAIMER
While every effort has been made to ensure the accuracy of this document, Raven
Industries assumes no responsibility for omissions and errors. Neither is any liability
assumed for damages resulting from the use of information contained herein.
Raven Industries shall not be held responsible or liable for the effects of atmospheric
conditions and sunspot activity on the performance of our products.
Raven Industries cannot guarantee the accuracy, integrity, continuity, or availability of
the GPS signal from the US Department of Defense/NAVSTAR GPS satellites, the
OmniSTAR correction service or the WAAS correction service.
Raven Industries accepts no responsibility for the use of the signal for other than the
stated purpose. Raven Industries shall not be responsible or liable for incidental or
consequential damages or a loss of anticipated benefits or profits, work stoppage or
loss or impairment of data arising out of the use or inability to use the Smartrax or any
of its components.

Manual # 016-0190-034
1
C H A P T E R
INTRODUCTION
Congratulations on your purchase of the Raven SmarTrax system! This system is designed
to provide cutting-edge, hands-free steering of your machine via GPS coordinates.

CaseIH SPX 3200 CC SmarTrax Installation Manual
2
Basic Kit
Contents
Below you will see the kit contents that you should have received with this SmarTrax
kit.
Case SPX 3200 CC SmarTrax Kit Contents
Quantity Item Description Part Number
1KIT, S.P.S. 063-0181-007
1PLATE, MOUNTING, UNIVERSAL HYDRAULIC,
PART "B" 107-0171-578
1WELDMENT, BRACKET, UNIVERSAL HYD.
MTG., PART "A" 116-0159-527
1HOSE, HYD., 13/16" ORFS (F) TO 9/16" JIC (F),
48" LG 214-1000-202
1HOSE, HYD., 13/16" ORFS (F) TO 9/16" JIC (F),
48" LG 214-1000-203
1HOSE, HYD., 13/16" ORFS (F) TO 9/16" JIC (F),
48" LG 214-1000-204
1HOSE, HYD., 13/16" ORFS (F) TO 9/16" JIC (F),
48" LG 214-1000-205
1HOSE, HYD., 9/16" ORFS (M) TO 9/16" JIC (F),
36" LG 214-1000-206
1HOSE, HYD., 9/16" ORFS (F) TO 9/16" JIC (F),
48" LG 214-1000-207
1SWITCH, PRESSURE, MICRO, H.D., 15-100 BAR
ADJ. W/FTG 422-0000-074
4FITTING, ELBOW, 45° SWIVEL, 9/16" JIC M/F 333-0012-027
4FITTING, ADAP[TER, SWIVEL RUN TEE, 13/16"
ORFS M/M/F 333-0012-028
4FITTING, ELBOW, 90° SWIVEL, 9/16" JIC M/F 333-0012-042
1FITTING, ADAPTER, SWIVEL RUN TEE, 3/4" JIC
M/M/F 333-0012-039
1
FITTING, ADAPTER, SWIVEL RUN TEE, 9/16" JIC
M/M/F 333-0012-043
2FITTING, ADAPTER, SWIVEL RUN TEE, 11/16"
ORFS M/M/F 333-0012-069
1FITTING, ADAPTER, REDUCING, 3/4" JIC (F) TO
9/16" JIC (M) 333-0012-141
1FITTING, UNION, SWIVEL, 9/16" JIC TO 9/16" JIC
(F) 333-0012-142
1FITTING, ADAPTER, SWIVEL, 3/4" JIC (F) TO
13/16" ORFS (M) 333-0012-143
2FITTING, ADPTR., UNION, 13/16" ORFS (M) TO
11/16" ORFS (M) 333-0012-144
2FITTING, UNION SWIVEL, 11/16" ORFS (F) TO
11/16" ORFS (F) 333-0012-145
1FITTING, ADAPTER, STRAIGHT, 13/16" ORFS
(M) TO 3/4" JIC (M) 333-0012-146
4BOLT, 5/16"-18 x 7/8" HEX HEAD 311-0052-104
4BOLT, HEX, 3/8"-16 UNC x 1/2" 311-0054-105
4NUT, 3/8"-16 312-1001-037
4WASHER, LOCK, 5/16" 313-1000-019
4WASHER, LOCK, SPLIT, 3/8" 313-1000-022
4WASHER, FLAT, 3/8" 313-2300-013
1VALVE, HYD., CLOSED CENTER LS 334-0003-062
1MANUAL, INSTALLATION 016-0190-034
1MANUAL, INSTALLATION, SMARTRAX 016-9001-021
1LABEL, WARNING, DO NOT STEP 041-0159-688
1LABEL, WARNING, TAMPERING 041-0159-689
1CABLE, HYDRAULIC SOLENOID / OVERRIDE 115-0171-466

Manual # 016-0190-034
3
C H A P T E R
SAFETY
Important: Hydraulics are under pressure. Never attempt to
open or work on a hydraulic system with the equipment running.
Care should always be taken when first opening a system that
was previously pressurized.
When disconnecting the hydraulic hoses or when purging is required, be aware
that the hydraulic oil within the machine system may be extremely hot and under
high pressure. Caution must be exercised. Any work carried out on the hydraulic
system must be performed in accordance with the machine manufacturerer’s
approved maintenance instructions. Raven Industries recommends that appropri-
ate protective equipment be worn when working on the hydraulic system. Ob-
jects or materials that are able to bypass the machine’s hydraulic filtration system
will adversely reduce performance and possibly damage the hydraulic valves.
Do not reverse the power leads. Doing so will cause severe damage to the
equipement. Always check to make sure that the power leads are connected to
the right polarity as marked. Ensure that the power cable is the last cable to be
connected.
Hydraulic
Safety
Requirements
Electical
Safety
Requirements

CaseIH SPX 3200 CC SmarTrax Installation Manual
4
We welcome your feedback about this manual. If you have any comments or
suggestions for improvement, please let us know by contacting our Customer
Support Center by any of the following methods:
wVia phone: [phone]
wViamail:
Raven Industries
FlowControl Division
205 E. 6th St.
Sioux Falls, SD 57104
wVia email: [email protected]
Contacting
Raven
Industries

Manual # 016-0190-034
5
1. Position the t-shaped bracket on a flat spot on the steel frame support
beam, just below the cab and behind the steering orbital.
2. Attach the universal mounting bracket to teh machine using the provided
bolts by drilling holes through the frame or by welding the bracket to the
frame.
C H A P T E R
MOUNTING THE UNIVERSAL BRACKET AND VALVE
Helpful Hint: Review the hose connections and
routingbefore drilling holes orweldingin order to assure
that the valve is mounted in a place where the supplied
hoses will reach it from the steering orbital.

CaseIH SPX 3200 CC SmarTrax Installation Manual
6
Notes:

Manual # 016-0190-034
7
C H A P T E R
HYDRAULICS
Installing the
Tank Hose
1. Remove the existing tank to orbital hose at the orbital and attach a
provided tee fitting to the orbital.
2. Re-connect the hose to the tee fitting.
3. Connect one end of the tank hose (P/N 214-1000-203) to the tee and the
other end to the T Port on the steering assist valve.
Helpful Hint: User may wish to install an elbow fitting on the
orbital or on the steering assist valve to properly route the hose.

CaseIH SPX 3200 CC SmarTrax Installation Manual
8
1. Remove existing left steer hose at the orbital and attach a provided tee
fitting to the orbital.
2. Re-connect the hose to the tee fitting.
3. Connect one end of the A-Port to Left Steer hose (P/N 214-1000-204)
to the tee and the other end to the A-port on the steering assist valve.
Helpful Hint: User may wish to install an elbow fitting
on the orbital or on the steering assist valve to properly
route the hose.
Installing
Pressure Hose
Installing
A-Port to Left
Steer Hose
1. Remove existing pressure hose at the orbital and attach a provided tee
fitting to the orbital.
2. Re-connect the hose to the tee fitting.
3. Connect one end of the Pressure hose (P/N 214-1000-202) to the tee and
the other end to the P-port on the steering assist valve.
Helpful Hint: User may wish to install an elbow fitting
on the orbital or on the steering assist valve to properly
route the hose.
1. Remove existing right steer hose at the orbital and attach a provided tee
fitting to the orbital.
2. Re-connect the hose to the tee fitting.
3. Connect one end of the B-Port to Right Steer hose (P/N 214-1000-205)
to the tee and the other end to the B-port on the steering assist valve.
Helpful Hint: User may wish to install an elbow fitting
on the orbital or on the steering assist valve to properly
route the hose.
Installing
B-Port to
Right Steer
Hose
Installing the
Pressure
Switch
1. Connect the pressure switch to the PS port on the steering assist valve.