Cashino CSN-80V User manual

CSN-80V User manual
1
CSN-80V Thermal Receipt printer
Protocol: Lin Xiaopeng 2017.04.06
Audit : Hu Riyu 2017.04.08
Standardize：Liu Zhonghua 2017.04.09
Authorize: Wang Huanyong 2017.04.11

CSN-80V User manual
2
Company: Xiamen Cashino Technology Co., Ltd.
Tel: [phone] Fax: [phone]
Address: 4/F,No.318,Tongji South Road, Jimei
District,Xiamen,China.361021
The manual is subject to change without further notice. Please contact Xiamen Cashino
Technology Co., Ltd. directly for the latest version.
revision record
Item
Date
Description
Edited
page
Desing
Review
1
20170406
The first draft
Lin
Xiaopeng
Hu Riyu
www.cashinotech.

CSN-80V User manual
3
Contents
1.Introduction.....................................................................................................................................7
1. 1 Unpacking.......................................................................................................................... 7
1.2 Name of each part of the printer..................................................................................... 7
2. Specifications................................................................................................................................8
3. Basic operation and usage.........................................................................................................8
3.1 open the paper bin cover..................................................................................................8
3.2 install the paper roll........................................................................................................... 9
3.3 set the printing mode (DIP switch)................................................................................10
3.4 Control panel.................................................................................................................... 10
3.5 self-test.............................................................................................................................. 11
3.6 printer connection POS80V interfaces: serial+USB+ Ethernet............................... 11
3.6.1 Serial interface:.....................................................................................................11
3.6.2 USB interface:.......................................................................................................12
3.6.3 Ethernet interface:................................................................................................12
4. Printer fault analysis.................................................................................................................. 12
4.1 Paper jam inclusion.........................................................................................................12
4.2 printer cleaning................................................................................................................ 13
5．Command Introduction............................................................................................................14
5.1 Command List.................................................................................................................. 14
5.2 Commands details...........................................................................................................16
①Printing and paper feed commands........................................................................16
Printing and paper feed.................................................................................................16
Enter................................................................................................................................. 17
Print and paper feed dots............................................................................................. 17
Print and paper feed n line........................................................................................... 17
②Printing set commands..............................................................................................18
Set print position.............................................................................................................18
Character right space setting....................................................................................... 18
Set line space as n dots................................................................................................18
Set horizontal and vertical movement units...............................................................19
Set line space to default................................................................................................19
Set character print font..................................................................................................20
Set character printing method......................................................................................20
Set character size.......................................................................................................... 21
Set、remove white printing.......................................................................................... 21
Set、remove underline................................................................................................. 22
Set、remove bold print................................................................................................. 23
Set、remove overlapping............................................................................................. 23
Set、cancel characters upside down......................................................................... 23
Set、remove 90°revolving printing............................................................................. 24
Allow、orbid key switch................................................................................................ 24
Set the left margin..........................................................................................................25

CSN-80V User manual
4
Set relative printing position......................................................................................... 25
Set printing alignment....................................................................................................26
Select、cancel user customized characters............................................................. 26
Define user customized characters.............................................................................26
Cancel user customized characters............................................................................29
Set / remove quadruple angle of Chinese print........................................................ 29
Set the Angle of Chinese character word space.......................................................30
Set up the Chinese characters to print mode combination.....................................30
Set Chinese mode......................................................................................................... 31
Exit Chinese character mode.......................................................................................31
Set and cancel under line of Chinese character mode............................................31
Set and cancel under line of Chinese character mode............................................31
Selecting international character set...........................................................................32
Select character code....................................................................................................33
③Graphic printing command....................................................................................... 34
Fill Graphics vertical module data............................................................................... 34
Print Graphics horizontal module data....................................................................... 36
Define downloaded bitmap...........................................................................................37
Print downloaded bitmap.............................................................................................. 38
Define NV bitmap........................................................................................................... 39
Print NV bitmap.............................................................................................................. 42
Print bitmap..................................................................................................................... 43
Print MSB bitmap........................................................................................................... 44
④Tab Commands.......................................................................................................... 45
Horizontal tab..................................................................................................................45
Horizontal tab position setting......................................................................................46
⑤One-dimension bar code command........................................................................47
1D bar code readable character(HRI) print position setting................................... 47
1D bar code readable character(HRI)font type selection........................................47
1D bar code height setting............................................................................................47
1D bar code width setting............................................................................................. 48
1D bar code printing...................................................................................................... 48
⑥Two-dimensional bar code commands..................................................................53
Mode type of QR code.................................................................................................. 53
Setting error correction level of QR code...................................................................54
Store QR code data to QR code data buffer............................................................. 54
Printing QR code............................................................................................................55
Setting QR code graph information.............................................................................55
Printing two dimensional code..................................................................................... 56
Printing two dimensional code..................................................................................... 57
Printing double QR code...............................................................................................58
⑦Status querying Commands.....................................................................................59
Transmission status....................................................................................................... 59
Transit the printer status to host.................................................................................. 60

CSN-80V User manual
5
Transit printer ID.............................................................................................................60
Select peripherals.......................................................................................................... 61
Real-time transmission status......................................................................................62
Real-time pulse...............................................................................................................66
⑧Commands in page print mode............................................................................... 67
Forms feed...................................................................................................................... 67
Data print in page print mode.......................................................................................67
Page print mode select................................................................................................. 67
Line print mode select................................................................................................... 68
Character development angle select in page print mode....................................... 68
Page print mode print area setting..............................................................................69
Vertical absolute position setting in page print mode.............................................. 70
Vertical relative position setting in page print mode.................................................71
Printer reset.....................................................................................................................71
Print self-test page......................................................................................................... 72
paper cut..........................................................................................................................72
Full cut..............................................................................................................................73
Partial cut.........................................................................................................................73
Specified pulse generation........................................................................................... 73
Setting up paper type.................................................................................................... 74
Feed to the beginning of the next label...................................................................... 74

CSN-80V User manual
6
PREFACE
It is very honor to cooperate with you. Before using the printer, please read this
user manual carefully, in order to properly use and better show the characteristics of this
Printer.
CAUTIONS
1. The printer should be installed in stable place to avoid vibration and impact.
2. Do not use and store printers in high humidity and dirty places.
3. Connect the power adapter of the printer to an appropriate grounding socket to avoid
using the same socket with a large motor or other device that can cause a power supply
voltage fluctuation.
4. Avoid water or conductive material (such as metal) inside the printer and turn off the
power as soon as it occurs.
5.If the printer is not used for a long time, please disconnect the power of the printer power
adapter.
6.The user shall not remove the printer for repair or modification without authorization.
7.The power adapter uses only a random power adapter that specially designed for.
8. In order to guarantee the quality and the life of the printer, it is recommended to use
high-quality printing paper in priority.
APPLICATIONS
1.Print POS system receipts.
2.Print EFT POS system receipts.
3.Print Gym, Post, Hospital, Civil Aviation system receipts.
4.Print inquiry, service system receipts.
5.Print instrument test receipts.
6.Print tax,tab receipts.

CSN-80V User manual
7
1.Introduction
1. 1 Unpacking
While open, make sure that the following parts are present and not damaged in
transportation.If have any question, please contact the supplier immediately!
1.2 Name of each part of the printer

CSN-80V User manual
8
⑴Power ⑵Key for opening the top cover ⑶control panel
⑷paper out mouth ⑸Top cover/paper cover ⑹printer case ⑺Functional dial
code switch cover ⑻Adjustment cover of cutter ⑼USB port ⑽Serial port（DB9）
⑾Lan port（RJ45） ⑿Cashdrawer port（RJ11）⒀DC outlet（DIN-3P）
2. Specifications
Printing
Printing method
Thermal printing
Printing speed
Max:250mm/s
Resolution
8dots/mm
Printing width
72mm
Character
Character set
ANK：12*24
GBK：24*24
Character font
ANK：(9*17,12*24)
Paper roll
Paper typr
Thermal paper
Paper width
80±0.5mm
Paper roll diameter
max：83mm
Paper thickness
50-80μm
Reliablity
MCBF
15 million lines
TPH
>100km
Cutter life
>1 million cuts
Interfaces
Serial
port/USB/LAN/Cashdr
awe
Serial
port/USB/Cashdr
awer
Command
ESC/POS compatible command sets
Cutter type
Full cutter/Partial cutter
Cashdrawer control
24V/1A （support 12V and 24V
cashdrawer）
Power supply
DC24V /2A
Dimensions (width * depth * height)
88*87*57mm
Environment
Operating temp
0°C ~ 50°C
Operating Humidity
20% ~ 85%RH
Storage temp
-20°C ~ 60°C
Storage Humindity
5% ~ 90%RH
3. Basic operation and usage
3.1 open the paper bin cover
When the printer needs to change the paper, the paper cover must be opened. When it is

CSN-80V User manual
9
opened, please press the open button on the left of the printer with your finger and press
down slightly to make the paper cover bounce up. Then, hold the paper cover with your
hand and flip it backwards.(see as image 1)
1
3.2 install the paper roll
Please use the correct type of paper roll.
1. Power off the printer;
2. Open the top cover(paper cover),
3. Take out the used up paper roll,(skip this step if the printer unused before),
4. install the new paper roll as shown in image 2,
5. Pull the paper out of the paper mouth;
6. Gently close the paper cover and buckle it in place.
2

CSN-80V User manual
10
3.3 set the printing mode (DIP switch)
From setting the DIP switch can change the cutter, language, speed, buzzer, printing
density and other settings mode of the printer.
ON-OF
F
Function
ON
OFF
1
cutter
No cutter
Have cutter
2
Beep reminder
close
open
3
Printing density
High
density
Normal density
4
/
/
/
5
characters per
line printed
64
48
6
/
/
/
7-8
Transmission speed (only useful to serial port )
- baud rate
SW7
SW8
Transmission speed（bps）
-bits/sec
ON
ON
9600
ON
OFF
19200
OFF
ON
38400
OFF
OFF
115200
Note: language and baud rate can be setted via printer setting tool.
3.4 Control panel

CSN-80V User manual
11
⑴ Feed
Press this key to feed the paper. Press this key continuously to keeping feeding the
paper .
⑵ Paper
If both the light and Error light are on at the same time, the printer is run out of paper; if
both the light and Error light are off, the printer has paper.
⑶ Power
This light on means the printer power on, this light off means the printer power off.
⑷ Error
When the printer is out of paper, cutter error, printed head overheated and other errors
occurs, lights flashing.
3.5 self-test
After the printer is connected, power off the printer firstly, and then press the Feed button
and power on of the printer simultaneously. After about 2 seconds, release the button and
the printer will print out the current status and printer Settings.
3.6 printer connection
POS80V interfaces: serial+USB+ Ethernet
3.6.1 Serial interface:
1) Data transmission mode: serial
2) Synchronous mode: asynchronous
3) Handshake signal: DTR / DSR or XON / XOFF control mode
4) Bit rate: .115200,57600,38400, 19200, 9600, 4800 the BPS is optional.
5) Word size: 8
6) Parity: no parity, odd parity, even parity optional.
7) Stop Bits: 1
8) Enter the polarity of the information:
Symbol (MARK) = logic 1 (-3 to-15VDC)
Space (SPACE) = logical 0 (+3 to +15 VDC)

CSN-80V User manual
12
Interface cable that along with the printer could be connected with the computer's
serial port.
3.6.2 USB interface:
1) USB outlet: type B.
2) With WINDOWS95/98, need to install the driver (the CD-ROM); with
WINDOWS2000,
XP, NT, do not need to install the driver.
3.6.3 Ethernet interface:
1) Need use setting software that are along with the printer to set IP address of the
printer (192.168.1.87)
same as the IP of your computer when use Ethernet interface.
2) The setup software, refer to the CD’s documentation.
4. Printer fault analysis
4.1 Paper jam inclusion

CSN-80V User manual
13
In the process of using the printer, if you come across the phenomenon of paper jam,
please stop printing in time and power off the printer. The paper jam is usually caused by
the failure of the automatic cutting cutter head to fully back into the body of the paper
cutter after the paper cutting.
When the phenomenon of paper jam occurs, it usually causes paper cover to be unable to
open normally. At this time, please do not forcibly open the cover to avoid damaging to the
printer.
The paper jam exclusion method is as follows:
1. Power off the printer and remove all connecting wires connected to the printer;
2. Pull out the paper cutter cover horizontally and forward as shown in image 4;
3. Rotate the cutter wheel with your finger to rewind the cutter head into the cutter body;
4. Press the "paper cover switch" button vertically downward to open the paper cover and
remove paper jam;
5. If the printing and paper out are normal, then reinstall the paper cutter cover.
4.2 printer cleaning
When one of the following situations occurs to the printer, the print head should be
cleaned:
4.2.1 printing is not clear;
4.2.2 The printed page for a column is not clear;
4.2.3 The paper is making a lot of noise.
The cleaning steps of the print head are as follows:
(1) Power off the printer, open the top cover, if there is paper, remove it;
(2 If you have just finished printing, wait for the print head to cool completely;
(3) with a soft cotton cloth dipped in anhydrous ethanol (should be wring dry) wipe off the
print head of the thermal sensor surface dust, stains;
(4) wait for anhydrous ethanol completely volatilization, close the cover, retry printing.
Note:
1 daily maintenance of printers must ensure that the power supply is turned off;
2 do not touch the surface of the print head with your hands and metal objects, do not use
tweezers and other tools to scratch the print head, printing cots and sensor surface;
3 can not use gasoline, acetone and other organic solvents;
4 wait for anhydrous ethanol completely evaporated, then turn on the power supply to
continue to print.

CSN-80V User manual
14
5．Command Introduction
5.1 Command List
ESC Command
ESC !
Set character printing method
ESC - n
Set and delete underline
ESC E n
Set and delete bold printing
ESC G n
Set and deleteoverlapping printing
ESC｛n
Set and delete inversion printing
ESC V n
Set and delete 90°rotate printing
ESC 1
Set line space n dots(same as ESC3）
ESC 2
Set default line space
ESC 3
Set line space n dots
ESC *
Bitmap vertical modulus data fillings
ESC d
Print and paper feed n lines
ESC % n
Choose and delete customized characters
ESC &
Define customized characters
ESC ? n
Delete customized character
ESC R n
International character sets
ESC t n
Select the character code page
ESC D
Set horizontal tabulation position
ESC J
Print and paper feed n dots
ESC p
Produce cashdrawer pulse
ESC c 5 n
Allow or prohibit to switch printer by button
ESC C
Undefined
ESC T n
Set printing direction in page print mode
ESC u
Peripheral device statustransmission
ESC v
Printer status transmission
ESC i
Full cuts
ESC @
Printer reset
ESC =
Select peripheralsdevice
ESC a
Setting position alignment mode
ESC $ nL nH
Set absolute print position
ESC \ nL nH
Set relative print position
ESC W
Page print mode print area setting
ESC L
Page print mode select
ESC S
Line print mode select
ESC FF
Data print in page print mode
ESC SP n
Character rightspace setting
ESC Z
Two-dimension Bar Code print
ESC M n
Set character print font

CSN-80V User manual
15
ESC m
Partly cuts
ESC q
Undefined
ESC Q
Undefined
GS Command
GS ! n
Set character size
GS *
Define download bitmap
GS / m
Print download bitmap
GS ：
Start or end macro definition
GS ^ r t m
Run macros
GS V m
Choose cut mode and cut
GS P x y
Set horizontal and vertical movement units
GS I n
Printer ID transmission
GS B n
Set and delete white printing
GS b
Undefined
GS H
Set 1-D barcode readable character(HRI)
print position
GS f n
Set HRI character
GS h
Set 1-D barcoe hight
GS w
Set 1-D barcode width
GS k
1-D barcode
GS L nL nH
Set left margin amount
GS a n
Allow or prohibit to upload the status automatically
GS r n
Transmission status
GS v
Transfer printer status to host
GS v 0
Bitmap horizontal modulus data print
GS (
2-D barcode print
GS $nL nH
Vertical absolute position setting in page print mode
GS \ nL nH
Vertical relative position setting in page print mode
FS Command
FS ！n
Kanji printing mode stored setting
FS &
Set Chinese character mode
FS .
Delete Chinese character mode
FS q
Define NV bitmap
FS p n m
Print NV bitmap
FS W n
Kanji quadruple size printing specification/
cancellation
FS – n
Set and delete kanji characterunderline
FS S n1 n2
Kanji character space Setting
FS 2
Undefined
FS A
Undefined

CSN-80V User manual
16
US Command
US Q
Print double QR CODE
US A
Set paper type
DLE Command
DLE EOT n
Real-time transmission status
DLE ENQ n
Real-time request
DLE DC4 fn m t
Real- time pulse
DC2 command
DC2T
Printing self-test page
DC2 *
Print bitmap
DC2 V
Print MSB bitmap
DC2 v
Print LSB bitmap
LF
Line feed
CR
Enter
FF
Forms feed
HT
Horizontal tab
SO
Paper feed to initial position at the next label
5.2 Commands details
①Printing and paper feed commands
Printing and paper feed
Name
print and paper feed
Code
ASCII ：LF
DEC ：10
HEX ：0A
Function
Print the buffer contest,and set the paper feed as per line space,then
adjust
print position to initial position at the next line.
Range
None
Default
None
Notes
None
Example
None

CSN-80V User manual
17
Enter
Name
Enter
Code
ASCII ：CR
DEC ：13
HEX ：0D
Function
Adjust print position to initial position of the same line.
Range
None
Default
None
Notes
After executing, R command, the new printing data will cover old data in
theprinting buffer.
Example
None
Print and paper feed dots
Name
Print and paper feed n dots
Code
ASCII ：ESC J n
DEC ：27 74 n
HEX ：1B 4A n
Function
Print the buffer content and paper feed
Range
0 ≤ n ≤ 255
Default
None
Notes
Paper feed n dots when printing buffer is empty.
After executing this command,printing position is moved to initial
Example
1b 40 30 31 32 1b 4a 10
Print and paper feed n line
Name
Print and paper feed n lines
Code
ASCII ：ESC d n
DEC ：27 100 n
HEX：1B 64 n
Function
Print the contents in printing buffer and paper feed n lines.
Range
0 ≤ n ≤ 255
Default
None
Notes
Print this command set as initial position of the same line
Example
1b 40 30 31 32 1b 64 01

CSN-80V User manual
18
②Printing set commands
Set print position
Name
Set print position
Code
ASCII ：ESC $ nL nH
DEC ：27 36 nL nH
HEX ：1B 24 nL nH
Function
Set left side blank area as（nL + nH × 256）dots
Range
0 ≤ nL ≤ 255
0 ≤ nH ≤ 255
Default
None
Notes
Set left side blank area as[(nL+nH*256)]*0.125mm]
This command is only effective with the initial position of the line.
This command is unavailable if it sets beyond the printing area.
Example
None
Character right space setting
Name
Character right space setting
Code
ASCII ：ESC SP n
DEC ：27 32 n
HEX ：1B 20 n
Function
Character right space setting as (n*0.125mm)
Range
0 ≤ n ≤ 255
Default
n = 0
Notes
When characters double width,Character right space is twice of
normal.When characters amplified,Character right space is n
times of normal.
This command doesn’t affect the setting of Chinese characters.
This command sets the standard values independently in each
mode.
Example
None
Set line space as n dots
Name
Set line space as n dots
Code
ASCII ：ESC 3 n
DEC ：27 51 n
HEX ：1B 33 n
Function
Set line space as n dots
Range
0 ≤ n ≤ 255
Default
n = 33
Notes
Line space as below:

CSN-80V User manual
19
If the line space settedis less than the highest character in that line,then
this line space is equal to the height of the highest character.
If ESC2,ESC@,reset the printer, the printer blackout,and the line
spaceturns to default.
Example
1b 40
1b 33 30
30 31 32 0d 0a
30 31 32 0d 0a
1b 32
30 31 32 0d 0a
30 31 32 0d 0a
Set horizontal and vertical movement units
Name
Set horizontal and vertical movement units
Code
ASCII ：GSP x y
DEC ：29 80 x y
HEX ：1D 50 x y
Function
Horizontal movement unit =25.4/x mm(1/x inch）
Vertica movement unit =l25.4/y mm(1/y inch）
When set X=0,Y=0, X and Y will display default value.
Range
0 ≤ x ≤ 255,0 ≤ y ≤ 255
Default
x=180,y=360
Notes
None
Example
None
Set line space to default
Name
Set line space to default
Code
ASCII ：ESC 2
DEC：27 50
HEX ：1B 32
Function
Set line space to default 30 dots
Range
None
Default
None
Notes
Line space in details pls check ESC 3 command.
If the line spacesettedis less than the height character in the line,the line
space of this line is equal to the height of the highest character
It can use ESC 3 to define line space.
Example
None

CSN-80V User manual
20
Set character print font
Name
set character print font
Code
ASCII ：ESC M n
DEC ：27 77 n
HEX ：1B 4D n
Function
set character print font
parameter n bit definition as below
n = 0，font 12*24
n = 1，font 9*17
Range
None
Default
n = 0
Notes
The command is effective withcharacter.
The command is disabled when ESC@, printer reset or blackout.
Example
1B 40 1B 4D 00 30 31 32 0D 0A
1B 40 1B 4D 01 30 31 32 0D 0A
Set character printing method
Name
Set character printing method
Code
ASCII ：ESC ! n
DEC ：27 33 n
HEX：1B 21 n
Function
Set character printing methods(font,highlight,inversion,bold,double
hight,double width and underline),parameter n bit definition as below:
Bit Function Value
0 1
0 FontNormal Small character
1 Undefined
2 Undefined
3Bold CancelSetting
4 Double hightCancel Setting
5 Double widthCancel Setting
6 Undefined
7 Underline Cancel Setting
Range
None
Default
n = 0
Notes
The command is effective with Chinese and foreign languages.
The command is disabled when ESC@, printer reset or power off
Example
1B 40 1B 21 01 30 31 32 0D 0A
1B 40 1B 21 02 30 31 32 0D 0A
1B 40 1B 21 04 30 31 32 0D 0A
1B 40 1B 21 08 30 31 32 0D 0A