CDVI KRYPTO K1BT Instruction Manual

www.cdvi.ca
QUICK START
INSTALLATION GUIDE
CDVI’s KRYPTO K1BT card reader facilitates high
security!
The K1BT KRYPTO bluetooth reader is
compatible with the ATRIUM BT mobile
application and the KRYPTO Mobile-PASS.
The K1BT works with the secure protocol of
CDVI, the encryption keys guarantee end-to-
end encryption between the credential, the
reader and the A22K door controller.
KRYPTO K1BT - High security made easy!
K1BT
KRYPTO Bluetooth
High-Security Card Reader
1.65"
(42 mm)
0.91"
(23 mm)
IP53
Certication
-25°C to +60°C
DEEE
Certication
• Works with ATRIUM A22K controller
• Compatible with ATRIUM BT application
and KRYPTO Mobile-PASS (Bluetooth)
• FULLY secure RS-485 connection (4 wires)
• Reads KRYPTO Mobile-PASS, 13.56 MHz
Mifare Classic and DESFire EV1/EV2
credentials
• OSDP-2 compatible
• Up to 2” (5 cm) read range
• Power requirements: 12 VDC
• Current consumption : 200mA

All the information contained within this document (pictures, drawing, features, specications and dimensions) could be perceptibly dierent and can be changed without prior notice. Printed in Canada - March 2021 - CDVI_K1BT_QS_01_EN_A4_CMYK.pdf
QUICK START
INSTALLATION GUIDE
www.cdvi.ca
Red : 12VDC
Black : GND
Green : D0 / A+ (RS485 BUS)
White : D1 / B- (RS485 BUS)
Blue : Not applicable
D1 / B-
RED1 GRN 1 BUZ 1
D0 / A+
12V
D1 / B-
RED 2 GND GND GND GND
GND
GRN 2 BUZ 2
D0 / A+
12V
+12V DC
+24V DC
-
+12V DC
-
+12V DC
A+
B-
C 1 NO 1 NC 1 LK 1+ LK 1
-
LK 2
-
C 2 NO 2 NC 2 LK 2+
C 1 REX 1 12V C 2 REX 2 12V
TMP
Input 1
Input 2
Output 1
Output 2
INPUT
POWER
SUPPLY
RS485
LOCAL
BUS
ETHERNET
PORT
SYSTEM STATUS
EXTRA
INPUTS/
OUTPUTS
A22K CONTROLLER
READER PORT DOOR 1
A22K CONTROLLER
READER PORT DOOR 2
DOOR 1 DOOR 2
ETHERNET LOCAL BUS LOCK 1 & 2
JUMPER SETTING
STATUS
24V DC INPUT/
BATTERY/
MODULE TYPE
BATTERY
BACKUP
ENCLOSURE
TAMPER
SWITCH
INPUT
INPUTS
DOOR 1 DOOR 2
LOCKS
DIP switch settings
located on the back of
the K1BT reader:
1: ON= Entry reader (default)
OFF= Exit reader.
You must restart the K1BT
after each change.
2: ON= KRYPTO reader (default)
OFF= OSDP reader
No need to reboot the reader
after every change.
3: Future use
4.13"
(105 mm)
• Connect wires as shown above in ‘‘Wiring Diagram’’.
• Once leveled and aligned, mark the mounting
holes of the reader.
• Drillthexingscrewholes.
Use provided anchors if required.
• Once the card reader is mounted to the wall,
place the screw cover caps on the reader.
Note: Each ATRIUM A22K controller support 2 reader
connected in parallel per port (ENTRY and EXIT readers).
Osetthereadersbyaminimumof6inchestoavoid
interference.
READER PORT #1 READER PORT #2
A22K CONTROLLER
Here are the LED statuses when connected to an
ATRIUM A22K controller:
Note:
Door output timings such as; unlock time (access granted),
door open too long pre-alarm and door open too long
alarm,canbemodiedintheATRIUMsoftware“Door
Properties” window.
LED State Buzzer Description
Steady blue - Standby (door secure)
Turn green for 5 sec. Chirp beep Access granted
5 rapid red blinks
Steady
beep for
3 sec.
Access denied
Flashing blue - Reader compromised
(lost its encryption key)
Blinks green every
3 sec. - Door unlock schedule
Flashing red Steady
beep Door forced alarm
Flashing red Beep every
2 sec.
Door open too long
pre-alarm
Flashing red rapidly Fast beep Door open too long
alarm
It is recommended to use twisted pair wiring as shown
below between the reader and the ATRIUM A22K controller.
Furthest reader can be installed up to 4,000 ft (1220 m)
from the A22K controller (AWG 22 cable).
D0 / A+
12V
D1 / B-
GND
CABLE CONNECTIONS
Wire Leads Connect to
A22K Reader Port
Red 12 VDC
Black GND
Green D0 / A+
White D1 / B-
WIRING DIAGRAM
LED STATUS INDICATORS
MOUNTING
21 3