CDVI V1ER User manual

The installer’s choice
cdvigroup.com
V1ER
V3E
V3ER
V3E35R
V4E
V4ER
V5E
Mortice Electromagnets
V1ER
V3E - V3ER
V3E35R
V5SRB
V4E - V4ER
V5SRB
ENGLISH
EN
V5E

2] REMINDERS AND RECOMMENDATIONS
1] PRODUCT PRESENTATION
Thank you for buying our products and for the condence you placed
in our company.
Mortice.
Monitored*.
Holding force: 180, 300, 400 or 500kg*.
Side load.
High corrosion resistance.
Delivered with armature plate.
No mechanical wear.
Ease of installation.
Recommended for indoor use.
Fail safe (Door unlocked when
power off ).
No residual magnetism.
Buit-in varistor: Electronic protection
to eliminate back EMF.
Electromagnetic lock dimensions (L x W x D):
- V1ER = 221 x 34 x 21mm.
- V3E series = 228 x 38 x 27mm,
- V3E35R = 228 x 35.5 x 24.5mm,
- V4E series = 229 x 43 x 27mm,
- V5E = 287 x 64 x 40mm.
Armature dimensions (l x w x d):
- 180kg = 130 x 32 x 9mm,
- 300kg = 185 x 38 x 11mm,
- 400kg = 185 x 45 x 12mm,
- 500kg = 185 x 60 x 12mm.
Silent operation.
Power supply: 12/24V dc.
Power absorption:
- 12 V DC = 500mA,
- 24 V DC = 250mA.
References Holding
force Monitored
V1ER 180kg
V3E 300kg -
V3ER 300kg
V3E35R 300kg
V4E 400kg -
V4ER 400kg
V5E 500kg -
EC certicationWEEE
IP42
2cdvigroup.com
RoHS
ARD212 BS602
Recommended
power supplies
* Depending on the version.
The function of an electromagnetic lock is to ensure the locking of an access point. This document is a guide
of installation which will allow you to secure the installation according to the characteristics of the product,
the site and the environmental requirements.
APPROVAL RELATIVE TO EMERGENCY EXITS
In the case of an installation of electromagnetic lock on emergency exits, it is imperative to make sure that
these exit points will be automatically free in case of re alarm, to open in the event of a re alarm to allow
evacuation of the premises. The electromagnetic lock installed on emergency exits must be in accordance
with the re approval department (Ex: In France = NF 61-937).
For more information, contact CDVI, the local re ofcer or the safety ofcer responsible for the building..
EN
V1ER - V3E - V3ER - V3E35R - V4E - V4ER - V5E
Mortice Electromagnetic locks
INSTALLATION MANUAL

3cdvigroup.com
MAINTENANCE
The Electro magnet and armature plate have a specic treatment which strengthens the protection against
wear and corrosion. These products do not require high maintenance. Nevertheless to ensure optimum
performance, it is recommended to clean regularly the surfaces in contact of the electro magnet and armature
plate with a cloth and non abrasive products. If traces of corrosion appear, it is recommended to clean and
oil the contact surfaces. Check and tighten regularly all the xings of the Electro magnet and ensure that
while the armature is able to pivot on its mounting, the xing bolt is not liable to loosen (we recommend
thread-lock for all xing bolts).
MOUNTING RECOMMENDATIONS
- Dene the level of security of the access.
- Determine the maximum strength of holding force to this level of security.
- Select the Diax®electromagnetic lock according to the environment, the inside, the outside, the climatic
constraints, (For example: stainless steel dedicated to an outside use).
- Always install the electromagnetic lock on the secure side of the place to be secured.
- Indeed make sure that the frame and opening, receiving or supporting the electromagnetic lock, armature
plate and their accessories, are solid and resistant to damage or wear over a period of time.
- Consider any bracketry required for the assembly according to the type of support receiving
the electromagnetic lock and armature plate.
- Dene the passage of cables to ensure the protection against the vandalism and the environmental
requirements (in particular through exible hoses of door, glands, gutters, cross cables, plastic tubes).
POWER SUPPLY
An electromagnetic lock always operates in DC current, a very low safety voltage. The Diax®electromagnetic
lock is recommended for use with power supplies manufactured by CDVI, however, other power supplies
may be used on condition that they are of equivalent quality and characteristics rectied, ltered, regulated
and protected by fuse in primary and secondary sectors.
Armature plate
- It is vital to x the electromagnetic lock
and armature plate solidly on their supports.
- Make sure that the magnet and the armature
meet evenly over their entire mating surfaces.
- The Armature plate must be able to pivot
slightly about its center mounting screw
to compensate for any door misalignment.
3] PACKAGE CONTENTS
Mortice
magnetic
lock
Armature
plate
Roll pin
5x16
Rubber
washer
10x6x4
Key
3mm
Guide
piece
Cap
nut
Installation
manual
M5x20
screw
M5x8
screw
Steel
washer
Joggle
bracket
112111111822
ELECTROMAGNETIC LOCK V1ER
EN
V1ER - V3E - V3ER - V3E35R - V4E - V4ER - V5E
Mortice Electromagnetic locks
INSTALLATION MANUAL

5] ELECTRICAL CONNECTIONS
The NO/NC signal only switches when the door is closed
with the power to it on.
TERMINAL
BLOCK CORRESPONDENCE V3E - V4E V5E
V1ER - V3ER
V3E35R - V4ER
+12 or 24V dc
-- 0 V
N.C NC (Normally closed) -
COM COM -
N.O NO (Normally open) -
4cdvigroup.com
Check the jumper position
before connecting the lock to the
input current. A wrong position
could damage the lock. This
type of damage is not covered
by the warranty.
IMPORTANT NOTE
12V dc factory setup
ELECTROMAGNETIC LOCK V3E - V3ER - V3E35R - V4E - V4ER - V5E
4] OPTIONAL ACCESSORIES
References
AMCCHANFR16
AMCCHANFR20
Description Armature
mounting plate
Mortice
magnetic
lock
Armature
plate
Roll pin
5x16
Steel
washer
Joggle
bracket (excepted
for the V5E)
M5x8
screw
Key
5mm
1122281
M8x35
screw
M8x25
screw
Guide
piece
Cap
nut
Rubber
washer
15x9x4
Installation
manual
111111
EN
V1ER - V3E - V3ER - V3E35R - V4E - V4ER - V5E
Mortice Electromagnetic locks
INSTALLATION MANUAL

5cdvigroup.com
V1ER - V3ER
V3E35R - V4ER
V3E - V4E - V5E
WITH BUILT-IN PCB BOARD
12V dc 24V dc
VOLTAGE
SELECTION
JUMPERS
6] INSTALLATION (WITH AMCCHANFR20 OR AMCCHANFR16)
DIRECT CONNECTION
12V DC
Red +
White
-
Green
Black
24V DC
Red +
White
-
Green
Black
CONTACT
Yellow NC
Blue COM
Orange NO
Steel washer
Roll pin
Armature plate
Rubber washer
Screw
Screw
Screw
Joggle bracket
Joggle bracket
Armature plate support
AMCCHANFR20 or
AMCCHANFR16
(Optional)
Screw
Armature screw
EN
V1ER - V3E - V3ER - V3E35R - V4E - V4ER - V5E
Mortice Electromagnetic locks
INSTALLATION MANUAL

6cdvigroup.com
7] FAULT FINDING
PROBLEM POSSIBLE CAUSE SOLUTION
Door locking
impossible
The lock is not receiving
DC current.
- Check that the wires are connected to the right
terminals.
- Check that the power supply is compatible.
- Check that the lock is connected to the circuit
correctly.
Holding force
reduced
The lock and the armature are not
lined up with each other.
- Check that the lock is connected to the circuit
correctly.
- Check that the electromagnet and the armature
are properly aligned.
- Check that the contact faces are free from dirt and rust.
- Check that the armature is soft mounted.
Low voltage or armature jammed.
- Check that the lock is receiving the correct power
supply satisfactorily.
- check the tightening of the armature
and the condition of the rubber.
Faulty reed
switch Voltage too low. Misalignment.
- Check the power supply.
- Cable cross section to be determined according
to the power supply and the locking.
- e.g.: 2 x 1.5mm2 ≥ 10m.
8] NOTES
EN
V1ER - V3E - V3ER - V3E35R - V4E - V4ER - V5E
Mortice Electromagnetic locks
INSTALLATION MANUAL

7cdvigroup.com
FR
V1ER - V3E - V3ER - V3E35R - V4E - V4ER - V5E
Ventouse électromagnétiques encastrées
MANUEL D’INSTALLATION

The installer’s choice
cdvigroup.com
Reference : G0301EN0458V01
Extranet : EXE-CDVI_IM MORTICE MAGLOCKS CMYK A5 EN 01
All the information contained within this document (pictures, drawing, features, specications and dimensions) could be perceptibly different and can be changed without prior notice.
*G0301EN0458V01*
CDVI Group
FRANCE (Headquarter/Siège social)
Phone: [phone]
Fax: [phone]
CDVI
FRANCE + EXPORT
Phone: [phone]
Fax: [phone]
CDVI AMERICAS
[CANADA - USA]
Phone: [phone]
Fax: [phone]
CDVI
BENELUX
[BELGIUM - NETHERLAND - LUXEMBOURG]
Phone: [phone]
Fax: [phone]
CDVI
TAIWAN
Phone: [phone]
Fax: [phone]
CDVI
SUISSE
Phone: [phone]
Fax: [phone]
CDVI
CHINA
Phone: [phone]
Fax: [phone]
CDVI
IBÉRICA
[SPAIN - PORTUGAL]
Phone: [phone]
Fax: [phone]
CDVI
ITALIA
Phone: [phone]
Fax: [phone]
CDVI
MAROC
Phone: [phone]
Fax: [phone]
CDVI
SWEDEN
[SWEDEN - DENMARK - NORWAY - FINLAND]
Phone: [phone]
Fax: [phone]
CDVI
UK
[UNITED KINGDOM - IRELAND]
Phone: [phone]
Fax: [phone]
CDVI DIGIT
FRANCE
Phone: [phone]
Fax: [phone]