CDVI SELWR433-SAT User manual

Fabricant de Contrôle d’Accès depuis 1985 Manufacturing Access Control since 1985
The installer’s choice
www.erone.com - www.cdvigroup.com
www.erone.com - www.cdvigroup.com
Receiver type: Superheterodyne
Operating frequency: 433,92 MHz
Power supply : 12 Vdc
Current consumption: 24 mA
Output type: Wiegand 26-bit
Operating temperature: -20 to +70 °C
Dimensions: 105 x 45 x 28 mm
Weight: 65 g
Input load: 50 Ohm
READER 2
INPUTS
LOCAL
BUS
READER 1
BATT.
POWER
SUPPLY
BELL
DOOR 2
12V Z6 GND Z7 Z8
C1 NO1 NC1 C2 NO2 NC2
GND Z9 Z10
12V Z1 GND Z2 Z3 GND Z4 Z5
AC22
2-Door Controller
1
2
Plug-in the card into the
7-way connector READER1
or READER2 of the Atrium
mother board AC22
SELWR433-SAT
RG58 - 50 Ohm
Tuned
Antenna
P1
Green LED
[Power]
Red LED
[Wiegand]
The product comes with a 433 Mhz stylo antenna.
F1001000079
Erone S2TR2641E1/E2/E4/E2M
Erone SETR2641AM1/AM2
Erone S3TR2641T2/T2/T4
Erone S7TR2641E4
Erone SETR2641-TM
The receiver ERONE type SELWR433-SAT is a plug-in receiv-
er card, operating at 433,92 Mhz in AM/ASK modulation.
The receiver has a 26-bit wiegand output.
The output connector of the card can be tted on:
Atrium AC22 : reader 1 or reader 2
Atrium A22 : readers - door 2 ( only )
The receiver is provided with an external tuned antenna which
can be xed on the Atrium metal box.
It can be mounted on the top of the
metal box of Atrium ( Fig.A) or on
the side, making use of the L-shape
bracket ( Fig. B)
Fig A
Fig B
1Introduction
2Specications
3Compatible transmitters
4Layout
5Mounting the antenna on Atrium box
6a Plug-in on AC22
6b Plug-in on A22
Plug-in the card into the 7-way
connector reserved to Door 2 of
the Atrium mother board A22

Fabricant de Contrôle d’Accès depuis 1985 Manufacturing Access Control since 1985
The installer’s choice
Manufactured by : CDVI WIreless SPA - Via Piave, 23 - 31020 S.Pietro di Feletto (TV) - Italy
Before starting transmitter memorization make sure the receiver
module is x to ATRIUM reader port and system is ON (power).
Green LED will lit on RX module.
When disabling facility code verication, the receiver will
accept any facility code and maintains the check on the key
button.
Do the following to disable facility code verication:
1) Press the Receiver Button button until the Red LED
turns on and then release it.
2) Within 1 sec. press Receiver Button again. At this
point the Red LED starts to ash quickly. Facility code
verication is now disable.
(To restore facility code verication, repeat the procedure)
WARRANTY
The warranty period for this product is 24 months, beginning from the
manufacturer date. During this period, if the product does not work
correctly, due to a defective component, the product will be repaired or
substituted at our discretion. The guarantee does not cover the plastic
container integrity. After-sale service is supplied at the factory.
!IMPORTANT
Receiver location is crucial for optimal system
performance. Place the receiver far from
interference sources such as magnetic elds or
radio emissions (neon ballasts, electric motors,
etc.). Ensure quality signal reception by doing
range tests before permanently mounting the
receiver.
TRANSMITTER BUTTON PROGRAMMING
1) Press Receiver Button P1 until the Red LED turns on, then
release it.
2) Press a transmitter button ( A, B, C or D)
3) The Red LED turns off and then make a short ash.
Any operation not allowed ( memorization with full memory,
memorization of already stored codes ) will cause 2 quick ashes
of Red LED.
4) Repeat step 2 for all each button needed.
All transmitters with the Facility code and the button which you have
just enrolled will now be detected by the receiver.
NOTE : The receiver memory doesn’t store the SERIAL NUMBER of
the transmitter but only the combination: “Facility code - Button ”.
The combinations can be, for example: 001-A, 001-B, 002-B, 003- B,
010-D, where 002 is the Facility code, B is the transmitter button and
so on.
Combinations as A+B or C+D are not allowed.
The receiver has a memory for 50 different combinations
You must add the serial number of the remote into the ATRIUM
access control system to benet access rights.
Application:
You have 2 garage doors in the same range (location): use one
RX module per garage door. The ‘‘A’’ button for garage entry
door (RX #1) and the ‘‘B’’ button for garage exit door (RX #2).
Facility code (FC)= 001 Serial Number (SN)=
12345 (card number)
FC001 SN12345
Facility code and serial number are located on the back of the
transmitter
ABAB
CD
IS-SATERUK Rev. 2 on 12/9/2016
7Transmitter memorization
8Disabling Facility code verication
A 1 second ash of Red LED indicates a valid signal.
A quick ash of Red LED indicates an invalid signal.
This procedure allows to erase receiver memory.
1) Press Receiver Button until Red LED turns on.
2) Release Receiver Button and then press it again until
Red LED starts to ash 3 times.
At this point all settings are erased, and the receiver is reset
to factory default : no signal on wiegand output will occur
anymore.
9Led Indicators
10 Memory Reset ( Factory defaults )
NOTE : The information contained in the transmitter signal is com-
posed by 4 main parameters: MANUFACTURER KEY, FACILITY
CODE, SERIAL NUMBER and BUTTON TYPE.
The receiver accepts only transmitters with the right Manufacturer
Key ( ERONE ) and sends out, on the wiegand bus, their SERIAL
NUMBER.
The receiver doesn’t output any signal unless a transmitter
programming is performed.