CEECO SSP-351 series User manual

SSP-351-X(SSP-310-X)-ISSUE4.0r1
SERVICE MANUAL
FOR
MODEL SSP-351-X
(FORMERLY SSP-310-X)
STAINLESS STEEL PANEL
TELEPHONE
Serving the Telephone Industry Since 1930
Communication Equipment 519 W South Park Street
& Engineering Company Okeechobee, FL 34972
Voice: 863-357-0798
Fax: [phone]

ISSUE 4.0
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
2
IMPORTANT INFORMATION
FOR
CUSTOMER
Please fill in before you continue.
The following information is necessary when calling CEECO for assistance.
MODEL NUMBER MODEL SSP-351-X STAINLESS STEEL
PANEL TELEPHONE.
SERIAL NUMBER
DATE MANUFACTURED
LOCATION INSTALLED
For us to better serve you, please have this information available when calling for
technical support.
CEECO
Communication Equipment and Engineering Company
519 W South Park Street
Okeechobee, FL 34972
863-357-0798- telephone
863-357-0006- facsimile
[email protected]
www.ceeco.net

ISSUE 4.0
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
3
TABLE OF CONTENTS
SECTION PAGE
1.0 INTRODUCTION................................................................................................. 4
2.0 GENERAL DESCRIPTION................................................................................ 4
3.0 OPERATION ........................................................................................................ 4
4.0 RECOMMENDED TOOLS AND TEST EQUIPMENT .................................. 4
5.0 INSTALLATION NOTES AND ASSEMBLY INSTRUCTIONS ................... 5
6.0 TESTING............................................................................................................... 7
7.0 SPECIFICATIONS............................................................................................... 7
8.0 PARTS LIST ......................................................................................................... 8
9.0 FCC NOTICE........................................................................................................ 9
10.0 REPAIR AND RETURN INFORMATION..................................................... 10
11.0 WARRANTY POLICY ...................................................................................... 11

ISSUE 4.0
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
4
1.0 INTRODUCTION
The practices in this manual provide installation and maintenance information for
Model SSP 351-X Stainless Steel Panel Telephone.
The information in this manual is subject to change without notification.
For information not included in this manual, please call or write:
CEECO
Customer Service
519 W South Park Street
Okeechobee, FL 34972
863-357-0798- telephone
863-357-0006- facsimile
[email protected]
www.ceeco.net
2.0 GENERAL DESCRIPTION
The CEECO Model SSP 351-X Stainless Steel Panel Telephone is designed for
special applications where a telephone must fit into a standard 4 gang mounting
box. The SSP-351-X will accept incoming calls only, the user cannot initiate a
call. This telephone could, however, be used in conjunction with external
automatic dialing equipment, which would allow phone calls to be made when the
handset is lifted.
3.0 OPERATION
An incoming call is indicated by an audible ringer. When the phone rings, lift the
handset. Normal operation will follow.
4.0 RECOMMENDED TOOLS AND TEST EQUIPMENT
Volt/Ohm Meter
1/4" Nut Driver
Flat Blade Screw Driver
Security Tool, CEECO Part Number 301-037

ISSUE 4.0
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
5
5.0 INSTALLATION NOTES AND ASSEMBLY INSTRUCTIONS
5.1 Using a 301-064 security tool (sold separately) loosen and remove the security
screws. The security tool is for a standard 5/32" button head screw generally used
on the framework of the phone booths.
5.2 Carefully separate the faceplate assembly from the mounting box by gently
pulling the faceplate forward.
5.3 Determine and remove the desired knock out hole for running the telephone wire,
and mount the masonry box as needed.
5.4 Run the telephone wire into the box and terminate on the provided RJ11C must
be used, as it contains required over-voltage protection circuitry.
5.5 The use of a gas tube or carbon station protector is recommended. The station
ground should not exceed 50 ohms.
5.6 Plug the modular line cord from the faceplate assembly into the RJ11C terminal
block.
5.7 Dress the line cable and modular jack away from the security screws and seat the
faceplate into the housing enclosure.
5.8 Secure the faceplate assembly by tightening the security screws.
WARNING
A. Never install telephone wiring during a lightning storm.
B. Never install telephone jacks in wet locations unless the jack is
specifically designed for wet locations.
C. Never touch uninsulated telephone wires or terminals unless the
telephone line has been disconnected at the network interface.
D. Use caution when installing or modifying telephone lines.

ISSUE 4.0
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
6
5.9 OVER-VOLTAGE PROTECTION DIAGRAM
CONFIDENTIAL
This drawing and all information contained
therein is confidential and is the exclusive
property of CEECO and may not be copied,
reproduced or disclosed to anyone, in any
manner whatsoever, or used for any purpose
other than for which it is provided to you,
without the prior written permission of
CEECO.

ISSUE 4.0
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
7
6.0 TESTING
6.1 Connect the phone to a DTMF test set or working phone line.
6.2 From the test set or another phone place a call to the phone.
6.3 Verify that the ringer is working.
6.4 Lift the handset and check that a normal conversation is allowed.
7.0 SPECIFICATIONS
INPUT POWER: C.O. Line Powered
LOOP CURRENT: 23mA min to 80mA max
IMPEDANCE: 600 ohms
HEARING AID
COMPATIBLE: Meets EIA standards
ENVIRONMENTAL: Temperature 0°C to 50°C
Humidity 20%-90% non-condensating
TELEPHONE COVER: Brushed 16 ga. Stainless Steel
PANEL TELEPHONE 4.55" Wide x 8 1/4" High x 2.60" inside
DIMENSIONS box x 3.10" outside box with handset
on hook
MOUNTING: Standard 4 gang electrical MASONRY box
7 13/32”H x 3 ¾”W x 3 ½”D
½ &3/4” Knockouts.
WEIGHT: Approximately 3 lb.
RINGER EQUIVALENCY: 0.4A
FCC REGISTRATION: BW-88T7-13716-TE-T
UL LISTED NO.: 6OF5
TYPE JACK: RJ11C

ISSUE 4.0
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
8
8.0 PARTS LIST
QUANTITY PART NUMBER DESCRIPTION
1 301-004 Handset with Armored Cord
1 301-009 Network
1 301-588 Hookswitch Cradle
1 301-581 Tongue and Bracket
2 301-570 Microswitch
1 301-018 Modular Cord
1 331-003 Stainless steel panel
1 12017 Electronic Ringer
4 311-008 Security Screw #6-32 x 1 1/2”
1 301-001 Mounting Box
(Standard, 4-Gang, Electrical Masonry Box)
OPTIONS:
1 30l-037 Security Tool

ISSUE 4.0
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
9
9.0 FCC NOTICE
9.1 FCC REGISTRATION AND REPAIR INFORMATION
Your new telephone has been registered with the Federal Communication
Commission (FCC) in accordance with Part 68. The FCC requires that
you be advised of certain requirements involving the use of this telephone.
9.2 CONNECTION WITH THE NATIONWIDE TELEPHONE
NETWORK
The FCC requires that you connect this telephone to the Nationwide
Telephone Network through a registered jack provided by the telephone
company in your area. This jack is a modular outlet which you can order
from your local telephone company.
9.3 NOTIFICATION TO THE TELEPHONE COMPANY
Before connecting this telephone, the FCC requires that you notify your
local telephone company business office. The number is in the front of
your phone book.
Tell them:
The "line" to which you will connect the telephone (your phone number)
and the telephone's FCC registration number and ringer equivalence
number. These numbers are listed in Section 9.0.
The FCC further requires that you notify your local telephone company
when permanently disconnecting this telephone.

ISSUE 4.0
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
1
0
10.0 REPAIR AND RETURN INFORMATION
10.1 WARRANTY REPAIR
Any device returned requiring warranty service, repair or credit must be
accompanied with a "Return Material Authorization" (RMA) FORM. It
must include: return shipping instructions, original purchase order number
and special marking instruction. A description of the trouble observed
must be attached to the defective unit. This information must be inside the
shipping container.
10.2 DIRECT ALL INQUIRES TO:
CEECO
Repair Department
863-357-0798- telephone
863-357-0006- facsimile
[email protected]
www.ceeco.net
10.3 NON-WARRANTY REPAIR
CEECO will repair equipment out of warranty for a set charge plus parts.
The customer must pay the shipping costs both directions.
10.4 RETURN FOR CREDIT
Material may be returned for credit only with prior approval. Material not
authorized for return is subject to a 20% restocking charge based on the
manufacturers list price. Return RMA must be requested no later than 30
days after original shipment.