CEECO SSP-560-F User manual

SSP-560-F-LPSPKPCB-ISSUE4.0
SERVICE MANUAL
FOR
MODEL SSP-560-F
HANDS FREE STAINLESS STEEL TELEPHONE
EQUIPPED WITH LOW POWER SPK P.C.B.
Serving the Telephone Industry Since 1930
Communication Equipment 519 W South Park Street
& Engineering Company Okeechobee, FL 34972
Voice: 863-357-0798
Fax: [phone]

ISSUE 4.0
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
2
IMPORTANT INFORMATION
FOR
CUSTOMER
Please fill in before you continue.
The following information is necessary when calling CEECO for assistance.
MODEL NUMBER MODEL SSP-560-F EQUIPPED WITH
LOW POWER SPK P.C.B.
SERIAL NUMBER
DATE MANUFACTURED
LOCATION INSTALLED
For us to better serve you, please have this information available when calling for
technical support.
CEECO
Communication Equipment & Engineering Company
519 W South Park Street
Okeechobee, FL 34972
863-357-0798- telephone
863-357-0006- facsimile
[email protected]
www.ceeco.net

ISSUE 4.0
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
3
TABLE OF CONTENTS
SECTION PAGE
1.0 INTRODUCTION................................................................................................... 4
2.0 GENERAL............................................................................................................... 5
3.0 PROGRAMMING .................................................................................................. 5
4.0 OPERATION .......................................................................................................... 6
5.0 RECOMMENDED TOOLS AND TEST EQUIPMENT .................................... 6
6.0 INSTALLATION NOTES AND ASSEMBLY INSTRUCTIONS ..................... 7
7.0 TESTING................................................................................................................. 8
8.0 SPECIFICATIONS................................................................................................. 9
9.0 PARTS LIST ......................................................................................................... 10
10.0 REPAIR AND RETURN INFORMATION....................................................... 11
11.0 WARRANTY POLICY........................................................................................ 12

ISSUE 4.0
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
4
1.0 INTRODUCTION
The practices in this manual provide installation and maintenance information for
the CEECO Model SSP 560-F Telephone.
The information in this manual is subject to change without notification.
For information not included in this manual, please call or write:
CEECO
Customer Service
519 W South Park Street
Okeechobee, FL 34972
863-357-0798- telephone
863-357-0006- facsimile
[email protected]
www.ceeco.net

ISSUE 4.0
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
5
2.0 GENERAL
The CEECO Hands free telephone is a sturdy, vandal resistant, Stainless Steel
Panel Speakerphone. Instead of a hookswitch and handset, the telephone has a
Press to start/Press to stop button for initiation and termination of phone calls.
Manual volume control is also provided inside the telephone.
3.0 PROGRAMMING
NOTE: It is recommended that you ground yourself to prevent ESD
damage to the PCB(s).
3.1 Remove the telephone from its housing by loosening the security screws
with the security tool (sold separately) and removing them.
3.2 Locate the blue plastic mini-jumpers on the PC board. They are used to
program the time out disconnect feature.
3.3 Place the blue mini-jumper at P.C. board location JP3 in the “ON”
position, if time out disconnect is to be used.
3.4 If the time out disconnect feature is to be used, place the blue mini-jumper
at P.C. board location JP2 as follows:
Position 1 (for ONE minute conversation time)
Position 3 (for THREE minute conversation time)
Position 5 (for FIVE minute conversation time)
3.5 If the time out disconnect feature is not desired, simply place the blue
mini-jumper at P.C. board location JP3 in the “OFF” position.

ISSUE 4.0
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
6
4.0 OPERATION
To make a call, press the "CALL" button located on the front of the phone and
wait for dial tone. The RED LED (if provided) will light at this time. When dial
tone is received the transmitter is muted and the phone waits for numbers to be
dialed.
After the call is complete, press the button again. The RED LED (if provided)
goes out and the call is terminated. If the user does not press the "CALL" button
when he or she is finished using the phone, then the phone will hang up when the
programmed time expires, assuming this feature was programmed.
5.0 RECOMMENDED TOOLS AND TEST EQUIPMENT
Volt/Ohm Meter
5/16" Nut driver
3/8" Nut Driver
Security Tool, CEECO Part Number 301-037
Flat Blade Screw Driver
DTMF Test Set

ISSUE 4.0
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
7
6.0 INSTALLATION NOTES AND ASSEMBLY INSTRUCTIONS
6.1 Using a 301-037 security tool (sold separately), loosen and remove the
security screws.
6.2 The security tool is for a standard 5/32" button head screw generally used
on the framework of the phone booths.
6.3 Separate the faceplate assembly from the apparatus box by pulling the
faceplate forward.
6.4 The apparatus box is designed to be mounted flush on any flat vertical
surface. Mounting holes are provided on the back and all sides of the
apparatus box.(If applicable)
6.5 Run the inside station wire into the apparatus box and terminate on the
RJ11C terminal block inside.
6.6 The use of a gas tube, or carbon station protector is recommended. The
station ground should not exceed 50 ohms.
6.7 Plug the modular line cord from the faceplate assembly into the RJ11C
terminal block.
6.8 Dress the line cable away from the security screws and seat the faceplate
into the apparatus box.
6.9 Secure the faceplate assembly by tightening the security screws.
*****WARNING*****
A. Never install telephone wiring during a lightning storm.
B. Never install telephone jacks in wet locations unless the jack is
specifically designed for wet locations.
C. Never touch uninsulated telephone wires or terminals unless
the telephone line has been disconnected at the network
interface.
D. Use caution when installing or modifying telephone lines.

ISSUE 4.0
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
8
7.0 TESTING
Action: Connect the phone to the line.
Press the "CALL" button.
Reaction: Dial tone.
Red LED lights (if provided).
Action: Dial a number.
Reaction: The called party answers.
A normal speakerphone conversation is allowed.
Action: Finish the conversation.
Press the "CALL" button, or wait until time out
occurs.
Reaction: Red LED goes out (if provided).
The call is terminated.

ISSUE 4.0
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
9
8.0 SPECIFICATIONS
INPUT POWER: C.O. Line powered
LOOP CURRENT: 27ma. min. 80ma. max.
IMPEDANCE: 600 ohms
SIGNALING: DTMF, 70ms tone, 50ms spacing
OUTPUT: -4.0 to -6.0dbm
ENVIRONMENTAL: Temperature 0°c to 50°c
Humidity 20%-90%
PROGRAMMING: Via DTMF keypad.
DIMENSIONS: 10.25" Wide X 13.125" High X 2.625 Depth
WEIGHT: 16 Pounds
RINGER EQUIVALENCY: 0.4A
TYPE JACK: RJ11C
UL LISTED NO.: 6OF5
FCC NO.: BWBUSA-73021-MT-E

ISSUE 4.0
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
1
0
9.0 PARTS LIST
QUANTITY PART NUMBER DESCRIPTION
6 406-019 Outer Cover Security Screw
1 301-018 Modular Line Cord
1 301-054 Modular Connector (RJ11C)
1 700-008 Keypad Cable
1 660-000 CEECO SPK Board
1 705-110 Connectorized Keypad
1 6020 Momentary Panel Switch
1 14024 Speaker
1 14067 Microphone
1 391-002 Stainless Steel Panel
1 361-01 Mounting Box
1 12017 Ringer
ACCESSORIES :
1 301-037 Security Tool