CEECO WPL-531-X User manual

WPL-531-X-SPK1.07-ISSUE4.0
SERVICE MANUAL
FOR
MODEL WPL-531-X
HANDS FREE EMERGENCY
WEATHERPROOF TELEPHONE
EQUIPPED WITH SPK1.07 FIRMWARE
Serving the Telephone Industry Since 1930
Communication Equipment 519 W South Park Street
& Engineering Company Okeechobee, FL 34972
Voice: 863-357-0798
Fax: [phone]

ISSUE 4.0
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
2
IMPORTANT INFORMATION
FOR
CUSTOMER
Please fill in before you continue.
The following information is necessary when calling CEECO for assistance.
MODEL NUMBER MODEL WPL-531-X EQUIPPED WITH
SPK1.07 FIRMWARE.
SERIAL NUMBER
DATE MANUFACTURED
LOCATION INSTALLED
For us to better serve you, please have this information available when calling for
technical support.
CEECO
Communication Equipment & Engineering Company
519 W South Park Street
Okeechobee, FL 34972
863-357-0798- telephone
863-357-0006- facsimile
[email protected]
www.ceeco.net

ISSUE 4.0
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
3
TABLE OF CONTENTS
SECTION PAGE
1.0 INTRODUCTION................................................................................................... 4
2.0 GENERAL............................................................................................................... 4
3.0 PROGRAMMING .................................................................................................. 5
PROGRAMMING CONTINUED................................................................................... 6
PROGRAMMING CONTINUED................................................................................... 7
4.0 OPERATION .......................................................................................................... 7
5.0 RECOMMENDED TOOLS AND TEST EQUIPMENT .................................... 7
6.0 INSTALLATION NOTES AND ASSEMBLY INSTRUCTIONS ..................... 8
7.0 TESTING................................................................................................................. 9
7.0 SPECIFICATIONS............................................................................................... 10
9.0 PARTS LIST ......................................................................................................... 11
10.0 REPAIR AND RETURN INFORMATION....................................................... 12
11.0 WARRANTY POLICY ........................................................................................ 13
12.0 DIAGRAM............................................................................................................. 14

ISSUE 4.0
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
4
1.0 INTRODUCTION
The practices in this manual provide installation and maintenance information for the
CEECO Model WPL-531-X Hands free Weatherproof Telephone with SPK1.07
firmware.
The information in this manual is subject to change without notification.
For information not included in this manual, please call or write:
CEECO
Customer Service
519 W South Park Street
Okeechobee, FL 34972
863-357-0798- telephone
863-357-0006- facsimile
[email protected]
www.ceeco.net
2.0 GENERAL
2.1 The CEECO Model WPL-531-X Hands free Weatherproof telephone is a
sturdy, vandal resistant, stainless steel weatherproof speakerphone. Instead
of a hookswitch and handset, the WPL-531-X has a Press to start/Press to
stop button for initiation and termination of phone calls. This Emergency
button is provided for automatic ring down applications. Manual volume
controls for the microphone and speaker are provided inside the phone.
2.2 Incoming calls may be allowed or blocked depending on the
programming.
2.3 Programming is accomplished via the DTMF keypad.

ISSUE 4.0
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
5
3.0 PROGRAMMING
3.1 Remove the front stainless steel panel by loosening the four security
screws with a security tool (sold separately) and remove them. Remove
the panel and attached telephone assembly.
3.2 Connect the telephone to a working telephone line or a DTMF test set.
3.2 Locate the pair of blue mini-jumpers located near the edge of the printed
circuit board. Move them to the “ON” or innermost position, as depicted
on the last page of this manual.
3.3 Locate the programming keypad, which is either mounted on the back
panel or provided on the side.
3.4 Each programming location is accessed by dialing the "#" sign and the two
digit code, which corresponds to that location. The only valid program
locations for this phone is : #00. The previous contents of the location are
automatically erased when the location code is dialed.
3.5 Location "00" is the telephone option location. By entering a number of 1-
9 into each of the 10 digits, the phone is customized for the particular
installation.
3.6 Press the “CALL & HANGUP” and wait to hear dial tone
3.7 Using the keypad, enter #00 followed by ten digits, as selected on the next
page..
NOTE:
THIS EQUIPMENT IS TELEPHONE LINE POWERED.DURING PROGRAMMING THE CENTRAL
OFFICE OR PBX MAY RESPOND TO THE PROGRAMMING CODES WITH VARIOUS BUSY TONE,
REORDER TONE,RECORDINGS,ETC.THESE TONES AND RECORDINGS WILL HAVE NO
EFFECT ON THE PROGRAMMING.PLEASE IGNORE THEM.

ISSUE 4.0
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
6
PROGRAMMING CONTINUED
LOCATION #00
Digit 1:
Always 0 for this model.
Digit 2:
0 No incoming calls allowed. (Default)
1 Incoming calls allowed.
Digit 3:
Always 0 for this model
Digit 4:
0 No time-out disconnect
1-9 Minutes time-out disconnect
Digit 5:
Always 1 for this model
Digit 6:
Always 0 for this model.
Digit 7:
Always 1 for this model
Digit 8:
Always 0 for this model
Digit 9:
Always 0 for this model
Digit 10:
00 No wink detect.
1-9 Length of the wink detect.
(1=50ms incremental to 450 ms. 5 is recommended).
•Be sure to enter your selections below for future reference.
#00= 0 __ 0 __ 1 0 1 0 0 5
DIGITS: 1 2 3 4 5 6 7 8 9 10

ISSUE 4.0
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
7
PROGRAMMING CONTINUED
3.8 When you are finished programming, press the “CALL & HANGUP”
button to hang up the phone. Return the two green mini-jumpers to the
“OFF” or outermost position, as depicted on the last page of this manual.
Secure the telephone assembly in the housing. The phone is now ready for
use.
4.0 OPERATION
To make a call, press the "EMER/CALL" button located on the front of the
phone. Wait to hear dial tone. The LED (if provided) will illuminate red at this
time. After the call is complete, press the "EMER/CALL" button on the front of
the panel again to hang up the phone. If the user does not press the button on the
front of the panel when he or she is finished using the phone, then the phone will
hang up after detecting a wink (open switch interval) or the timer times out.
5.0 RECOMMENDED TOOLS AND TEST EQUIPMENT
DTMF Test Set
Volt/Ohm Meter
CEECO Security Tool, 301-064

ISSUE 4.0
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
8
6.0 INSTALLATION NOTES AND ASSEMBLY INSTRUCTIONS
6.1 Using a 301-064 security tool (sold separately), loosen and remove the
security screws.
6.2 The security tool is for a standard 5/32" button head screw generally used
on the framework of the phone booths.
6.3 Separate the faceplate assembly from the weatherproof housing by pulling
the faceplate forward.
6.4 Run the inside station wire into the enclosure and terminate on the RJ11C
terminal block inside.
6.5 The use of a gas tube station protector is recommended. The station
ground should not exceed 50 ohms.
6.6 Plug the modular line cord from the faceplate assembly into the RJ11C
terminal block.
6.7 Dress the telephone line cord and AC cable away from the security screws
and seat the faceplate into the weatherproof housing.
6.8 Secure the cover assembly by tightening the security screws.
*****WARNING*****
A. Never install telephone wiring during a lightning storm.
B. The telephone must be grounded in accordance with local and
national electric codes.
C. Never install telephone jacks in wet locations unless the jack is
specifically designed for wet locations.
D. Never touch uninsulated telephone wires or terminals unless the
telephone line has been disconnected at the network interface.
E. Use caution when installing or modifying telephone lines.

ISSUE 4.0
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
9
7.0 TESTING
Action: Connect the phone to the line.
Press the "EMER/CALL" button.
Reaction: Phone goes off-hook.
Action: The called party answers
Reaction: A normal speakerphone conversation is allowed.
Action: Finish the conversation.
Press the "EMER/CALL" button, or wait until
time out occurs.
Reaction: The call is terminated.

ISSUE 4.0
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
10
7.0 SPECIFICATIONS
INPUT POWER: C.O. Line powered
110\120vAC for optional strobe light
LOOP CURRENT: 23mA minimum 80 mA maximum
IMPEDANCE: 600 ohms
SIGNALING: Manual on-off hook
OUTPUT: -4.0dbm to -6.0dbm
ENVIRONMENTAL: Temperature 0o C to 50o C
Humidity 20%-90%
PROGRAMMING: Via DTMF keypad.
MEMORY RETENTION: Lithium Battery - Long life
WEIGHT: 21 Pounds
DIMENSIONS: 9.20" Wide x 20.20" High x 7.30" Deep
MOUNTING: 4 Holes spaced 8"x 5 7/8" x 13/32" dia.
TYPE JACK: RJ11C
UL LISTED NO.: 6OF5