CEECO WPP-530-D User manual

WPP-530-D OR SSP-510-D-LPSPKRPCB+ATD11-ISSUE4.0
SERVICE MANUAL
FOR
MODEL WPP-530-D
HANDS FREE EMERGENCY
WEATHERPROOF TELEPHONE
OR
MODEL SSP-510- D
HANDS FREE STAINLESS STEEL
PANEL TELEPHONE
EQUIPPED WITH
LOW-POWER SPEAKER BOARD
Serving the Telephone Industry Since 1930
Communication Equipment 519 W South Park Street
& Engineering Company Okeechobee, FL 34972
Voice: 863-357-0798
Fax: [phone]

ISSUE 4.0
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
2
IMPORTANT INFORMATION
FOR
CUSTOMER
Please fill in before you continue.
The following information is necessary when calling CEECO for assistance.
MODEL NUMBER MODEL WPP-530-D OR SSP-510-D, EQUIPPED
WITH LOW-POWER SPEAKER BOARD AND
ATD-11 AUTO-DIAL PCB.
SERIAL NUMBER
DATE MANUFACTURED
LOCATION INSTALLED
For us to better serve you, please have this information available when calling for technical
support.
CEECO
Communication Equipment and Engineering
Company
519 W South Park Street
Okeechobee, FL 34972
863-357-0798- telephone
863-357-0006- facsimile
[email protected]
www.ceeco.net

ISSUE 4.0
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
3
TABLE OF CONTENTS
SECTION PAGE
1.0 INTRODUCTION................................................................................................... 4
2.0 GENERAL............................................................................................................... 4
3.0 PROGRAMMING .................................................................................................. 5
4.0 TESTING/OPERATION ....................................................................................... 9
5.0 RECOMMENDED TOOLS AND TEST EQUIPMENT .................................... 9
6.0 INSTALLATION NOTES AND ASSEMBLY INSTRUCTIONS ................... 10
7.0 SPECIFICATIONS............................................................................................... 12
8.0 PARTS LIST: ........................................................................................................ 13
9.0 FCC NOTICE........................................................................................................ 14
10.0 REPAIR AND RETURN INFORMATION....................................................... 15
11.0 WARRANTY POLICY ........................................................................................ 16

ISSUE 4.0
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
4
1.0 INTRODUCTION
The practices in this manual provide installation and maintenance information for
the CEECO Model WPP-530-D hands free weatherproof Telephone or the SSP-
510-D hands free stainless steel panel telephone.
The information in this manual is subject to change without notification.
For information not included in this manual, please call or write:
CEECO
Customer Service
519 W South Park Street
Okeechobee, FL 34972
863-357-0798- telephone
863-357-0006- facsimile
[email protected]
www.ceeco.net
2.0 GENERAL
2.1 The CEECO Model WPP-530-D or SSP-510-D Hands Free Telephone is a
sturdy, vandal resistant, stainless steel panel speakerphone. Instead of a
hookswitch and handset, the WPP-530-D or SSP-510-D has a Press to
start/Press to stop button for the initiation and termination of phone calls.
This Press to start/Press to stop Auto Dial button is provided for one
button dialing of a preprogrammed number of up to 11 digits. The
microphone is muted during the dialing sequence to prevent the use of
hand-held dialers. Fully line powered, no battery backup required for
memory retention.
2.2 Programming is accomplished via DTMF keypad.

ISSUE 4.0
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
5
3.0 PROGRAMMING
NOTE: It is recommended that you ground yourself to prevent ESD
damage to the PCB(s).
3.1 This phone has two “programmable features”, both of which are
controlled by the manipulation of mini-jumpers on the PC boards. The
phone can be programmed to automatically dial a number of up to eleven
digits in length. The phone can also be programmed to automatically
disconnect a phone call after the elapse of a selected period of time (1, 3 or
5 minutes). A pair of small needle nose pliers may be helpful with
moving the mini-jumpers, however; you must be very careful not to touch
the circuit boards with the pliers, as this may cause damage.
3.2 PROGRAMMING THE NUMBER TO AUTODIAL (ATD-11):
Please refer to the diagram on page 7 for programming the ATD-11.
If the number to be programmed is a (1+) or long-distance call, locate the
plastic mini-jumper at the “J1” position location of the ATD11 printed
circuit board. The ATD11 circuit board has a smaller board mounted to it,
which has several rows and columns of copper contacts/pins on it. The
“J1” position you are looking for is located just below the bottom right
hand corner of that smaller piggyback board. The “J1” position has three
copper contacts/pins, with a plastic mini-jumper, and is readily identified
by the “+1” that appears on the board in small white print just to its left.
By moving the plastic mini-jumper so that it bridges the middle copper pin
and the far left or “+1” pin, you will cause the digit “1” to automatically
dial out prior to any other programmed number. If your desired number is
local or does not need a preceding one, then move the mini-jumper to
bridge the middle copper pin and the far right pin. You will observe a “P”
in small white print on the circuit board just right of this right hand pin.
Next, locate the plastic mini-jumper at the “J3” position of the circuit
board, which is just below the “J1” position. It could also be considered
the second plastic mini-jumper below the bottom right hand corner of the
smaller piggyback board. Just left of this “J3” position, in small white
print, appears “11”. Be sure this mini-jumper is placed closest to the “11”,
bridging the middle and far left copper pins. The “J3” mini-jumper should
always be in this position, regardless of the number you are programming.

ISSUE 4.0
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
6
PROGRAMMING CONTINUED…
Now let’s program the number to be automatically dialed. Looking at the
piggyback circuit board containing several rows and columns of copper
pins, you will see ten plastic mini-jumpers. The rows are labeled 1 thru 0
on the left side of the circuit board. The columns are labeled A thru K
across the top of the circuit board and the columns of copper pins are in
pairs. Each pair of copper pins represents a number to be dialed. For
example, let’s assume that you want to program the phone to dial 1-954-
587-5430. Place the plastic mini-jumper under column “A” across the two
copper pins that align with row “9”. Place the mini-jumper under column
“B” so that it bridges the pair of copper pins in row “5”. Place the mini-
jumper under column “C” across the pair of copper pins in row “4” and so
on, until the entire number is programmed. Each column represents a
digit, so do not skip any. This example happens to include a long distance
number, so you would move the “J1” jumper to the “+1” position. If your
desired number was short, like 911 for example, the programming would
be slightly different. In a case such as that, you would place the jumper
under column “A” in the “9” position and the jumpers under columns “B”
and “C” in the “1” position. You would then remove the seven remaining
plastic mini-jumpers, so that no erroneous digits dial out.
3.4 Be sure each mini-jumper is properly positioned to make good contact and
dial the intended number. Do not discard unused mini-jumpers, as you
may need them in the future. It may be wise to tape them to the inside of
the phone somewhere out of harms way.
3.5 There is one last mini-jumper location that has not been addressed yet.
This jumper is positioned at the time of manufacturing to accommodate
most telephone environments. If your telephone line delivers dial tone to
your phone in one second or less, then you should proceed to section 3.6.
If you happen to be in a long loop environment, which takes more than
one second to deliver dial tone on the line, then you will need to locate the
plastic mini-jumper located at the “J2” position of the ATD11 board. On
this particular model phone, the “J2” position is hidden under the low-
power speaker board. You will first have to remove the screws, which
secure the low-power speaker board, and gently raise the board enough to
locate the mini-jumper. You must be very careful to avoid touching the
circuit boards with metal objects, as this may cause damage. The “J2”
position can be found approximately 1.5” – 1.75” directly below the “J1”
and “J3” positions and is somewhat by itself. Position the “J2” green,
plastic mini-jumper, so that it bridges the middle and far right copper pins.
A “3” appears in small white print just right of this position. Placing the
jumper there will cause the phone to delay 3 to 4 seconds

ISSUE 4.0
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
7
PROGRAMMING CONTINUED…
before dialing. This should allow the phone to accommodate those extra
long loop situations in terms of time to receive dial tone. When you have
completed this, carefully replace the low-power speaker board and secure
it with the screws.
3.6 PROGRAMMING DIAGRAM

ISSUE 4.0
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
8
3.6 PROGRAMMING THE TIME OUT DISCONNECT FEATURE:
If you desire the phone to automatically disconnect the call after a
specified period of time, we will discuss that now. Otherwise proceed to
section 3.7.
The low power speaker board, which is the larger printed circuit board,
has two plastic mini-jumpers on it, just like the ones you have been
manipulating thus far. These mini-jumpers are used to program the Time
Out Disconnect feature. Locate the plastic mini-jumper that has “JP3”
written above it in small white print on the PC board. Below it, in small
white print, appear the words “ON” and “OFF”. Place the mini-jumper
across the middle and far-left copper pins. This is the "ON" position,
which activates the Time Out Disconnect feature. When this feature is not
used, the jumper should be in the “OFF” position (jumper bridges the
middle and far right copper pins).
When utilizing the Time Out Disconnect feature, you select a 1, 3, or 5
minute timed disconnect. Locate the plastic mini-jumper on the same
circuit board; above which appears “JP2” in small white print. Below it
are “5”, “3” and “1” also in small white print. Place the jumper so that it
bridges the two copper pins corresponding with your selection of 1, 3, or 5
minutes.
3.7 Programming is now complete and the telephone is ready for
testing/operation.
3.8 Programming Diagram for Low Power Speaker Board:

ISSUE 4.0
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
9
4.0 TESTING/OPERATION
Action: Connect the phone to a working telephone line or DTMF test set.
Press the "CALL" button.
Reaction: Dial tone. Red LED illuminates (If equipped)
The preprogrammed number is automatically dialed.
Action: The called party answers.
Reaction: A normal speakerphone conversation is allowed.
Action: Finish the conversation and press the "CALL" button to hang up.
Reaction: Red LED goes out. (If equipped) and the call is terminated. If you
do not hang up the phone it will automatically disconnect if you programmed it as
such.
5.0 RECOMMENDED TOOLS AND TEST EQUIPMENT
Security Tool, CEECO part number 301-064
Insulated Needle Nose Pliers
Flat Blade/Phillips Head Screwdriver

ISSUE 4.0
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
10
6.0 INSTALLATION NOTES AND ASSEMBLY INSTRUCTIONS
6.1 Using a 301-064 security tool (sold separately), loosen and remove the
security screws.
6.2 The security tool is for a standard 5/32" button head screw generally used
on the framework of the phone booths.
6.3 Separate the faceplate assembly from the weatherproof housing by pulling
the faceplate forward.
6.4 Run the inside station wire into the enclosure and terminate on the RJ11C
terminal block inside, as depicted on the following page. The CEECO
provided terminal block (jack) must be used, as it contains required over-
voltage protection circuitry.
6.5 The use of a gas tube station protector is recommended. The station
ground should not exceed 50 ohms.
6.6 Plug the modular line cord from the faceplate assembly into the RJ11C
terminal block.
6.7 Dress the telephone line cord and AC cable away from the security screws
and seat the faceplate into the weatherproof housing.
6.8 Secure the cover assembly by tightening the security screws.
WARNING
A. Never install telephone wiring during a lightning storm.
B. Never install telephone jacks in wet locations unless the
jack is specifically designed for wet locations.
C. Never touch uninsulated telephone wires or terminals,
unless the telephone line has been disconnected at the
network interface.
D. Use caution when installing or modifying telephone lines.

ISSUE 4.0
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
11
6.9 OVER-VOLTAGE PROTECTION DIAGRAM
CONFIDENTIAL
This drawing and all information contained
therein is confidential and is the exclusive
property of CEECO and may not be copied,
reproduced or disclosed to anyone, in any
manner whatsoever, or used for any purpose
other than for which it is provided to you,
without the prior written permission of
CEECO.

ISSUE 4.0
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
12
7.0 SPECIFICATIONS
1. INPUT POWER C.O. Line powered
2. LOOP CURRENT 28ma. min. 80ma. max.
3. IMPEDANCE 600 ohms
4. SIGNALING DTMF, 70ms tone, 50ms spacing
5. OUTPUT -4.0 to -6.0dbm
6. ENVIRONMENTAL Temperature 0c to 50c Humidity 20%-90%
non condensating
7. PROGRAMMING Via DTMF keypad.
8. DIMENSIONS:
Stainless Steel Panel (SSP)
7 1/6∀wide x 11 1/4∀high x 4 1/4∀deep
(handset on hook).
9. PANEL MOUNTING (SSP) Vertical Surface Mount
10. WEIGHT ( SSP) Approximately 4lb.
11. DIMENSIONS:
Weatherproof Housing (WPP)
9 1/2" wide x 12 5/8" high x 8" deep
(including door).
12. WEATHERPROOF
HOUSING (WPP)
Cast aluminum
13. HOUSING MOUNTING (WPP) 4 holes spaced 8" x 5 7/8" x 13/32"
14. HOUSING WEIGHT (WPP) Approximately 12 pounds
15. MEMORY RETENTION Non-volatile memory retention
16. FCC REGISTRATION NO. BW-88T7-13716-TE-N
17. TYPE JACK RJ11C
18. U.L. LISTED NO. 6OF5

ISSUE 4.0
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
13
8.0 PARTS LIST:
QUANTITY PART NUMBER DESCRIPTION
4 331-006 OUTER COVER SECURITY SCREW
1 301-018 MODULAR LINE CORD
1 301-054 MODULAR CONNECTOR (RJ11C)
1 660-100 CEECO LPSPKR BOARD
1 12017 RINGER
1 6020-B MOMENTARY PANEL SWITCH
1 ATD-11 AUTO-DIAL PCB
1 14123 SPEAKER
1 530-D OR 510-D FACE PLATE
1 331-005 WEATHERPROOF HOUSING
ACCESSORIES :
1 301-064 SECURITY TOOL

ISSUE 4.0
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
14
9.0 FCC NOTICE
9.1 FCC REGISTRATION AND REPAIR INFORMATION
Your new telephone has been registered with the Federal Communication
Commission (FCC) in accordance with Part 68 of its rules. The FCC
requires that you be advised of certain requirements involving the use of
this telephone.
9.2 CONNECTION AND USE WITH THE NATIONWIDE TELEPHONE
NETWORK.
The FCC requires that you connect this telephone to the Nationwide
Telephone Network through a registered jack provided by the Telephone
Company in your area. This jack is a modular outlet, which you can order
from your local telephone company.
9.3 NOTIFICATION TO THE TELEPHONE COMPANY
Before connecting this telephone, the FCC requires that you notify your
local telephone company business office. The number is in the front of
your phone book.
Tell them:
The "line" to which you will connect the telephone (that is, your phone
number), the telephone's FCC registration number and ringer equivalence
number. These numbers are listed in section 7.0
The FCC further requires that you notify your local telephone company
when permanently disconnecting this telephone.

ISSUE 4.0
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
15
10.0 REPAIR AND RETURN INFORMATION
10.1 WARRANTY REPAIR
Any device returned requiring warranty service, repair or credit must be
accompanied with a "Return Material Authorization" (RMA) FORM. It
must include: return shipping instructions, original purchase order number
and special marking instruction. A description of the trouble observed
must be attached to the defective unit. This information must be inside
the shipping container.
10.2 DIRECT ALL INQUIRES TO:
CEECO
Repair Department
863-357-0798- telephone
863-357-0006- facsimile
[email protected]
www.ceeco.net
10.3 NON-WARRANTY REPAIR
CEECO will repair equipment out of warranty for a set charge plus parts.
The customer must pay the shipping costs for both directions.
10.4 RETURN FOR CREDIT
Material may be returned for credit only with prior approval. Material
authorized for return is subject to a 20% restocking charge based on the
manufacturer's list price. Return Material Authorization must be
requested no later than 30 days after original shipment.
10.5 EXCHANGE POLICY
If a replacement unit is required it will be shipped in the most expedient
manner consistent with the urgency of the situation. Please contact
"Customer Service" for instructions regarding exchange of modules or
printed circuit boards.

ISSUE 4.0
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
16
11.0 WARRANTY POLICY
11.1 GENERAL
CEECO products are guaranteed to be free of defects in material and
workmanship for a period of 365 days from the date of original purchase.
CEECO's obligation under this warranty is limited to repair or
replacement of any part found to be defective by CEECO. Under no
circumstances shall CEECO be liable for loss, damage, cost of repair or
consequential damages of any kind which have been caused by neglect,
abuse, acts of GOD or improper operation of equipment.
11.2 PRINTED CIRCUIT BOARDS
Printed circuit boards should not be field repaired. If a unit is found to be
faulty, replace it with another unit and return the faulty unit to CEECO for
repair. Modifications by anyone other than CEECO will void the
warranty.