Chauvet SlimPAR Pro Tri User manual

User Manual

Page 2 of 12 SlimPAR™ 64 User Manual Rev. 5
TABLE OF CONTENTS
1. Before You Begin................................................................................3
What is Included............................................................................................3
Unpacking Instructions..................................................................................3
Text Conventions..........................................................................................3
Icons.............................................................................................................3
Document Information...................................................................................3
Product at a Glance.......................................................................................3
Safety Notes .................................................................................................3
2. Introduction.........................................................................................5
Product Overview..........................................................................................5
3. Setup...................................................................................................5
AC Power......................................................................................................6
Fuse Replacement.................................................................................................6
Power Linking........................................................................................................6
Mounting................................................................................................................7
Orientation.............................................................................................................7
Rigging..................................................................................................................7
4. Operation ............................................................................................8
Control Panel Operation................................................................................8
Menu Map.....................................................................................................8
Configuration (DMX)......................................................................................8
Starting Address ....................................................................................................8
Configuration (Standalone)............................................................................9
Sound-Active Mode................................................................................................9
Automatic Mode.....................................................................................................9
Static Mode............................................................................................................9
Custom Static Colors..............................................................................................9
Master/Slave Mode................................................................................................9
DMX Channel Assignments and Values.......................................................10
7-CH Mode..........................................................................................................10
3-CH Mode..........................................................................................................10
5. Technical Information ......................................................................10
General Maintenance..................................................................................10
6. Technical Specifications..................................................................11
Returns.......................................................................................................12
Claims.........................................................................................................12
Contact Us..................................................................................................12

SlimPAR™ 64 User Manual Rev. 5 Page 3 of 12
1.BEFORE YOU BEGIN
What is
Included
•1 x SlimPAR™ 64
•1 x Power Cord
•Hanging Bracket with Mounting Hardware
•1 x Warranty Card
•1 x Quick Reference Guide
Unpacking
Instructions
Immediately upon receiving this product, carefully unpack it and check the container in
which you received it. Make sure that you have received all the parts indicated above
and that they are all in good condition. If the material inside the container (thi
s product
and any other accessory included with it) appears damaged from shipping, or if the
container shows signs of mishandling, notify the shipper immediately. In addition, retain
the container and all the packing material for inspection.
See the Claimssection in the Technical Information chapter.
Text
Conventions
Convention Meaning
<Menu>
A key to be pressed on the fixture’s control panel
1—512
A range of values
50/60 A set of values of which only one can be chosen
Claims
A section or chapter in this document
Settings
A menu option not to be modified (for example, showing the operating
mode/current status)
Menu > Settings
A sequence of menu options to be followed
ON
A value to be entered or selected
Icons
Icon
Meaning
Critical installation, configuration, or operation information. Failure to
comply with this information may render the fixture partially or completely
inoperative, cause damage to the fixture, or cause harm to the user.
Important installation or configuration information. Failure to comply with
this information may prevent the fixture from functioning correctly.
Useful information.
Document
Information
The information and specifications contained in this document
are subject to change without notice.
CHAUVET® assumes no responsibility or liability for any errors or omissions
that may appear in
this manual.
© Copyright 2013 CHAUVET®. All rights reserved.
Electronically published by CHAUVET® in the United States of America.
Product at a
Glance
Use on Dimmer
x
Auto Programs
P
Outdoor Use
x
Auto-ranging Power Supply
P
Sound-Activated
P
Replaceable Fuse
P
DMX
P
User-Serviceable
x
Master/Slave
P
Safety Notes
Please read the following notes carefully before starting to work with this product.
They include important safety information about its
the installation, usage, and
maintenance.
Please read the following notes
carefully because they include important safety
information about the installation, usage, and maintenance of this product.
•
Keep this User Manual for future consultation. If you sell this product to another user,
be sure that they also receive this document.

Page 4 of 12 SlimPAR™ 64 User Manual Rev. 5
•Always make sure that the voltage of the outlet to which you are connecting this
product is within the range stated on the decal or rear panel of the fixture.
•This product is for indoor use only! To prevent risk of fire or shock, do not expose
this fixture to rain or moisture.
•Make sure there are no flammable materials close to the unit while operating.
•Always install this product in a location with adequate ventilation, at least 20 in (50
cm) from adjacent surfaces.
•Be sure that no ventilation slots on the unit’s housing are blocked.
•Always disconnect this product from the power source before cleaning it or replacing
the fuse.
•Make sure to replace the fuse with another of the same type and rating.
•If mounting this product overhead, always secure it to a fastening device using a
safety cable.
•The maximum ambient temperature (Ta) is 104° F (40° C). Do not operate this
product at higher temperatures.
•In the event of a serious operating problem, stop using the unit immediately.
•Never try to repair this product. Repairs carried out by unskilled people can lead to
damage or malfunction. Please contact the nearest authorized technical assistance
center.
•Never connect this product to a dimmer pack.
•Make sure the power cord is not crimped or damaged.
•Never disconnect the power cord by pulling or tugging on the cord.
•Never carry this product from the power cord or any moving part. Always use the
mounting bracket.
•Always avoid direct eye exposure to the light source when this fixture is on.

SlimPAR™ 64 User Manual Rev. 5 Page 5 of 12
2.INTRODUCTION
Product Overview
Microphone Sensitivity
Adjustment Knob
Control Panel
LED Display Satellite™ 12 V Input
Fuse Holder
Power In
Power Out
Bracket
Adjustment Knob

Page 6 of 12 SlimPAR™ 64 User Manual Rev. 5
3.SETUP
AC Power
This product has an auto-ranging power supply and it can work with an input voltage
range of 100~240 VAC, 50/60 Hz.
To determine the power requirements for a particular fixture, see the label affixed to the
back plate of the fixture or refer to the fixture
’s specifications chart. A fixture’s listed
current rating indicates its average current draw under normal conditions.
Always connect this product to a protected circuit (circuit breaker or fuse),
making sure that it has an appropriate electrical ground
to avoid the risk of
electrocution or fire.
Never connect this product to
a rheostat (variable resistor) or dimmer circuit, even
if the rheostat or dimmer channel serves only as a 0 to 100% switch.
Fuse
Replacement
This fixture uses an F 1 A, 250 V fuse. Follow the instructions below to change it in case
it blows.
Disconnect this product from the power outlet before replacing the fuse.
1) Wedge the tip of a flat-head screwdriver into the slot of the fuse holder and pry it out
of its housing.
2) Remove the blown fuse from its holder and replace it with a fuse of the exact same
type and rating.
3) Insert the fuse holder back in its place, and reconnect power.
This product ships with a spare fuse inside the safety cap, as shown above.
Power Linking
This fixture provides power linking via the Edison outlet located in the front of the unit.
Please see the diagram below for further explanation.
Power Linking
Diagram
You can power link up to 40 SlimPAR™ 64 units on 120 VAC or up to 60
SlimPAR™ 64 units on 230 VAC.
The power linking diagram shown above corresponds to the North American
version of this product ONLY! If using this product in other markets, you must
consult with the local CHAUVET® distributor as power linking connectors and
requirements may differ in your country or region.
Installed fuse
(held by plastic clip)
Spare fusel
(inside safety cap)
Safety cap
1st Fixture
2nd Fixture
3rd Fixture
Other fixtures

SlimPAR™ 64 User Manual Rev. 5 Page 7 of 12
Mounting
Before mounting this product, read and follow the safety recommendations indicated in
the Safety Notes section (page 2 of this manual).
Orientation
The SlimPAR™ 64 may be mounted in any position, provided there is adequate room for
ventilation around it.
Rigging
Before deciding on a location for this product, always make sure that it will be easy to
access the unit for maintenance and programming purposes.
Make sure that the structure onto which you are mounting this product can support its
weight. Please see the Technical Specifications
section of this manual for weight
information.
When mounting this product overhead, always use a safety cable. Mount the fixture
securely to a rigging point, whether an elevated platform or a truss.
When rigging this product onto a truss, you should use a mounting clamp
of appropriate
weight capacity. The bracket has a 13 mm hole, which is appropriate for this purpose.
When power linking multiple fixtures, you must
always consider the length of the power
linking cable and mount the fixtures close enough for the cable to reach them.
The bracket knobs allow for directional adjustment when aiming the fixture to the desired
angle. Only loosen or tighten the bracket knobs using your bare hands. Using tools
could damage the knobs.
The double bracket yoke/mounting brackets/feet also serve
as floor support(s) or
surface mounting. When mounting this fixture on the floor, make sure that the fixture and
its cables are away from people and vehicles.
Mounting Diagram
Double-Bracketed
Yoke
Mounting Clamp
Safety Cable

Page 8 of 12 SlimPAR™ 64 User Manual Rev. 5
4.OPERATION
Control Panel
Operation
To access the control panel functions, use the four buttons located underneath the
display. Please refer to the Product Overview (page 5
) to see the buttons location on the
control panel.
Button Function
<MENU > Press to find an operation mode or to back out of the current menu
option
<UP>
Press to scroll up the list of options or to find a higher value
<DOWN> Press to scroll down the list of options or to find a lower value
<ENTER> Press to activate a menu option or a selected value
Menu Map
Mode
Programming Steps
Description
P--
P1
7 color program (switching)
P2
7 color program (fading)
P3
3 color program (switching)
P4
3 color program (fading)
P5
7 color program (sound-active)
P6
3 color program (sound-active)
3-CH
d001~d512
3-channel DMX mode (RGB)
7-CH
7-channel DMX mode
C--
C1
Red
Static
C2
Green
C3
Blue
C4
Cyan
C5
Magenta
C6
Yellow
C7
White
S--
S001~S100
Program speed for P1~P4
U--
r--
Red (r000~1000)
Custom Static Colors:
Combine red, green, and blue
g--
Green (g000~100)
b--
Blue (b000~100)
Configuration
(DMX)
Set this product in DMX mode to control it with a DMX controller.
1) Connect this product to a suitable power outlet.
2) Turn this product on.
3) Connect a DMX cable from the DMX output of the DMX controller to the DMX input
socket of this product.
Starting Address
When selecting a starting DMX address, always consider the number of DMX channels
the selected DMX mode uses. If you choose a starting address that is too high, you
could restrict the access to some of the fixture’s channels.
The SlimPAR™ 64 uses up to seven DMX channels in the 7-
CH personality, which
defines the highest configurable address to 507.
If you are not familiar with the DMX protocol, download the DMX Primer
from
www.chauvetlighting.com.
To select the starting address, do the following:
1) Press <MENU>repeatedly until 3-CH or 7-CH shows on the display.
2) Press <ENTER>.
3) Use <UP> or <DOWN> to select the starting address (d001~d507).
4) Press <ENTER>.

SlimPAR™ 64 User Manual Rev. 5 Page 9 of 12
Configuration
(Standalone)
Set this product in one of the standalone modes to control it without a DMX controller.
•Connect this product to a suitable power outlet.
Never connect a fixture that is operating in any standalone mode, whether Static,
Automatic, or Sound to a DMX string connected to a DMX controller. This is
because fixtures in standalone mode may transmit DMX signals that could
interfere with the DMX signals from the controller.
Sound-Active
Mode
To enable the Sound-Active mode, do the following:
1) Press <MENU> repeatedly until P-- shows on the display.
2) Press <ENTER>.
3) Use <UP> or <DOWN> to select P5 or P6.
4) Press <ENTER>.
5) Turn the music on and adjust the microphone sensitivity knob until the fixture starts
reacting to the beat of the music.
The fixture will only respond to the low frequencies of the music (bass and
drums).
Automatic Mode
To enable the Automatic Mode, follow the instructions below:
1) Press <MENU> repeatedly until P-- shows on the display.
2) Press <ENTER>.
3) Use <UP> or <DOWN> to select P1~P4.
4) Press <ENTER>.
5) Press <MENU> repeatedly until S-- shows on the display.
6) Use <UP> or <DOWN> to adjust the speed at which the program plays (S001~100).
7) Press <ENTER>.
Static Mode
To enable the Static mode, do the following:
1) Press <MENU>repeatedly until C-- shows on the display.
2) Press <ENTER>.
3) Use <UP> or <DOWN> to select the preset color (C1~C7).
4) Press <ENTER>.
Custom Static
Colors
To enable the Custom Static Colors mode, do the following:
1) Press <MENU>repeatedly until U-- shows on the display.
2) Press <ENTER>.
3) Use <UP> or <DOWN> to select the desired color: red (r--), green (g--),or blue (b--).
4) Press <ENTER>.
5) Use <UP> or <DOWN> to select the desired color value (000~100).
NOTE: Selecting 000 will turn the color off.
6) Press <ENTER> to continue to the next color.
7) Repeat steps 5 to 7 until you create your desired color.
8) Press <ENTER> to save the color.
Master/Slave
Mode This mode allows a single SlimPAR™ 64
unit (the “master”) to control the actions of one
or more SlimPAR™ 64
units (the “slaves”) without the need of a DMX controller. The
master unit will be set to operate in either Automatic or Sound-Active mode, while the
slave units will be set to operate in Slave Mode. Once set and connected, the slave units
will operate in unison with the master unit.
Configure the units as indicated below.
Slave units:
1) Press <MENU> repeatedly until 3-CH or 7-CH shows on the display.
2) Press <ENTER> to accept.
3) Use <UP> or <DOWN> to set the starting address to d001.
4) Press <ENTER>.
5) Connect the DMX input of the first slave unit to the DMX output of the master unit.
6) Connect the DMX input of the subsequent slave units to the DMX output of the
previous slave unit.
7) Finish setting and connecting all the slave units.
Master unit:
1) Set the master unit to operate in either Automatic or Sound mode, as previously
indicated.
2) Make the master unit the first unit in the DMX daisy chain.

Page 10 of 12 SlimPAR™ 64 User Manual Rev. 5
•Configure all the slave units before connecting the master unit to the DMX
daisy chain.
•
Never connect a DMX controller to a DMX string configured for Master/Slave
operation because it may interfere with the signals from the master unit.
•Do not connect more than 31 slave units to the master unit.
DMX Channel Assignments and Values
7-CH Mode Channel Function Value Setting
1
Red
000
ó
255
0~100%
2
Green
000 ó255 0~100%
3
Blue
000
ó
255
0~100%
4
Color Macros
(Overrides CH 1~3)
000
ó
015
016
ó
255
No function
Color Macros
5
Speed
(When CH.6 is between 032~223)
000 ó255 0~100%
Strobe 000 ó015
016
ó
255
No function
Slow~fast
6 Mode
000
ó
031
032 ó063
064 ó095
096 ó127
128 ó159
160 ó191
192 ó223
224 ó255
RGB mode
Pulse effect 0%~100%
Pulse effect 100%~0%
Pulse effect 100%~0%~100%
Auto fade transition
Auto snap transition (3 colors)
Auto snap transition (7 colors)
Sound triggering mode
7
Dimmer
000
ó
255
0~100%
3-CH Mode Channel Function Value Setting
1
Red
000
ó
255
0~100%
2
Green
000 ó255 0~100%
3
Blue
000
ó
255
0~100%
5.TECHNICAL INFORMATION
General
Maintenance
Dust build-up reduces light output performance and can cause overheating. This can
lead to reduction of the light source’s life and mechanical wear. To maintain optimum
performance and minimize wear, you should clean your lighting fixtures at least twice a
month. However, be aware that us
e and environmental conditions could be contributing
factors to increase the cleaning frequency.
To clean this fixture, follow the instructions below:
•Unplug the fixture from power.
•Wait until the fixture is at room temperature.
•Use a vacuum (or dry compressed air) and a soft brush to remove dust collected on
the external surface and vents.
•Clean the LED transparent cover with a mild soap solution, ammonia-free glass
cleaner, or isopropyl alcohol.
•Apply the solution directly to a soft, lint-free cotton cloth or a lens cleaning tissue.
•Softly wipe any dirt or grimeto the outside edges of the LED transparent cover.
•Gently polish the transparent LED cover until it is free of haze and lint.
Always dry the transparent LED cover carefully after cleaning.

SlimPAR™ 64 User Manual Rev. 5 Page 11 of 12
6.TECHNICAL SPECIFICATIONS
Dimensions and
Weight
Length
Width
Height
Weight
9.7 in (246 mm)
11.1 in (282 mm)
2.5 in (64 mm)
2.8 lbs (1.3 kg)
Note: Dimensions in inches rounded to the nearest decimal digit.
Power
Power Supply Type
Range
Voltage Selection
Switching (internal)
100~240 V, 50/60 Hz
Auto-ranging
Parameter
120 V, 60 Hz
230 V, 50 Hz
Power
32 W
36 W
Operating current
0.3 A
0.2 A
Power linking current (units)
10 A (40 units)
10 A (60 units)
Fuse
F 1 A, 250 V
F 1 A, 250 V
Power I/O
US/Worldwide
UK/Europe
Power input connector
IEC
IEC
Power output connector
Edison
IEC
Power Cord plug
Edison (US)
Local plug
Light Source
Type
Power
Lifespan
LED
¼ W
100,000 hours
Color
Quantity
Current
Red
60
20 mA
Green
60
20 mA
Blue
60
20 mA
Photo Optic
Parameter
Value
Illuminance @ 1 m
3,640 lux
Illuminance @ 2 m
1,241 lux
Beam angle
14º
Field angle
23º
Thermal
Maximum External Temp.
Cooling System
104° F (40° C)
Convection
DMX
I/O Connectors
Connector Type
Channel Range
3- pin XLR
Sockets
3, 7
Ordering
Product Name
Item Code
Item Number
SlimPAR™ 64
03030271
SLIMPAR64

Page 12 of 12 SlimPAR™ 64 User Manual Rev. 5
Returns
Send the merchandise prepaid, in the original box, and with its original packing and
accessories. CHAUVET® will not issue call tags.
Call CHAUVET®
and request a Return Merchandise Authorization (RMA) number
before shipping the fixture. Be prepared to provide the model number, serial number,
and a brief description of the cause for the return.
The user must clearly label the package with a Return Mer
chandise Authorization (RMA)
number. CHAUVET® will refuse any product returned without an RMA number.
DO NOT write the RMA number directly on the box. Instead, write it on a properly
affixed label.
Once you have received the RMA number, please include the following information on a
piece of paper inside the box:
•Your name
•Your address
•Your phone number
•RMA number
•A brief description of the problem
Be sure to pack the fixture properly. Any shipping damage resulting from inadequate
packaging will be the customer’s responsibility. FedEx packing or double-boxing are
recommended.
CHAUVET®
reserves the right to use its own discretion to repair or replace
returned product(s).
Claims
The carrier is responsible for any damage incurred during shipping to this product or any
part that shipped with it. Therefore, if the received merchandise appears to have
damages caused during shipping, the customer must submit the damage report and any
related claims with the carrier, not CHAUVET®. The customer must sub
mit the report
upon reception of the damaged merchandise. Failure to do so in a timely manner may
invalidate the customer’s claim with the carrier.
For other issues such as missing components or parts, damage not related to shipping,
or concealed damage, the customer must make claims to CHAUVET® within 7 days of
receiving the merchandise.
Contact Us
World Headquarters
CHAUVET®
General Information
Address: 5200 NW 108th Avenue
Sunrise, FL 33351
Voice: [phone]
Fax: [phone]
Toll free: [phone]
United Kingdom & Ireland
CHAUVET® Europe Ltd.
General Information
Address: Unit 1C
Brookhill Road Industrial Estate
Pinxton, Nottingham, UK
NG16 6NT
Voice: [phone]
Fax: [phone]
Technical Support
Voice: [phone] (Press 4)
Fax: [phone]
Email: [e-mail]
Technical Support
Email: [e-mail]
World Wide Web
www.chauvetlighting.com
World Wide Web
www.chauvetlighting.co.uk