Chauvet Patriot CH-545X User manual

World-wide Headquarters:
3000 North 29th Ct., Hollywood, FL
USA 33020
Tel: [phone] Fax: [phone]
www.ChauvetLighting.com
Patriot
CH-545X
User Guide
Please read these instructions carefully before use

Introduction
Congratulations on the purchase of your new CHAUVET lighting effect. We are confident that you will be
happy with the products that we provide. To assist you with the care and use of this product we have pre-
pared a short guide.
General Setup
Before connecting this unit to the mains power supply, you must first install the lamp. (See 'Replacing
Lamps' for details).
This lighting effect has been designed to function on a mains power supply of 120V~60Hz and has been
fitted with a suitable power plug.
DMX Mode
The Patriot (CH-545X) is a DMX fixture that can be operated with Chauvet's DMX-6 controller, DMX-40
DMX controller, DMX-50 Pro Controller, ShowXpress, or any other universal DMX controller. The CH545X
will also work in stand alone mode by sound activation. To operate in DMX mode, you must link the units
together using a premium quality 3-pin DMX cable in the following configuration. "Out" from the first unit
to "In" on the second, "Out" from the second unit to "In" on the third, and so on.
The Patriot (CH-545X) is a single channel DMX fixture. In order to activate the DMX mode, DIP switch
# 10 must be in the OFF position. Please consult the controller manual to determine the proper address
for the Patriot (CH-545X).
Example: To set the address at 12
•Lamp Replacement Cover
Set
Screw
•DIP Switches
At Rear
•Fuse Holder
•Power Connector
•Voltage Selector Switch
Front
•Microphone
•Sound Sensitivity
Adjustment
•DMX In
•DMX Out
1.Set SW 10 to OFF.
2. Count the value of the switches in the on position.
SW 3 equals 4 and SW 4 equals 8.
3. Set SW 3 and SW 4 to the ON position. (4 + 8 = 12)
12345678910
Off
On
Value 1 2 4 8 16 32 64 128 256

DMX Signal Levels
Sound Activated Mode
When dip switch SW #10 is on, the Patriot will be in sound activated mode. The light will cycle through
pre-programmed movements. If there is no sound for 20 seconds, the lamp will automatically black out.
Installation / Mounting
This unit has been designed to be properly mounted using a suitable hanging clamp and safety cable.
CHAUVET offers a range of items, which are ideal for safe mounting.
Mount the Patriot (CH545X) in a well-ventilated area without obstruction to the fan to prevent damage
from overheating.
DMX512 control value Remark
0-9 Black-out
10 Light On
11-30 Light On
31-99 Light On
100-105 Black-out
106-110 Light On
111-125 Light On
126-200 Light On
201-255 Sound-Activated
Static
Static
Clockwise Slow
Clockwise Fast
Counterclockwise Fast
Various
Rotating Direction
Static
Static
Counterclockwise Slow

Replacing Lamps
1. Always disconnect the unit from main power supply before attempting to replace a lamp or fuse.
2. Make sure that the unit is sufficiently cool before removing a blown lamp.
3. Never touch a new lamp with your fingers, use a tissue or a dry clean cloth. Touching a halogen lamp
with you r fingers will greatly reduce lamp life.
4. Unscrew the lamp replacement cover, which is highlighted on the diagram (fig.1). Only use the appro-
priately rated lamp, as use of any other lamp type may cause the unit to be non-operational.
5. Place the prongs of the lamp into the sockets located inside the unit. Check to make sure that the
lamp is housed correctly in the lamp holder and will not fall out.
6. Screw the lamp replacement cover back into place.
Note:If the unit is still not working after lamp replacement, please contact your dealer or
CHAUVET for servicing.
Replacing Fuses
1. Always disconnect the unit from main power supply before attempting to replace a lamp or fuse.
2. Unscrew the fuse holder cover to reveal the fuse.
3. Remove the old fuse.
4. Place new fuse inside the holder. **Notes on fuses - see below**
5. Screw the fuse holder cover back on.
Notes on fuses
This unit has a label attached which indicates the correct fuse rating. If needed, you can also find this
listed as part of the specifications for the unit later in this guide. It is critical that replacement fuses are
of the correct rating. Failure to use the correct fuse could damage the lighting effect beyond economic
repair.
If the unit is still not working after fuse replacement then please contact your dealer or CHAUVET for
servicing.
Specifications
Voltage: AC 110V 50/60Hz or 240V 50Hz
Fuse: 7 Amp 125V, 5 Amp 250V
Lamp: EHJ, 24V 250W
Motors: DC 12V 60 RPM
DC 12V 40 RPM
DC 12V 20 RPM
Colors: Red, Yellow, Blue, Orange, Green, White
Weight: 19 lbs
Dimensions: 14.25in x 11.25in x 11.25