Chauvet SlimPANEL TRI 24 IP User manual

User Manual

Page 2 of 17 SlimPANEL™ TRI 24 IP User Manual (Rev. 4)
TABLE OF CONTENTS
1. Before You Begin ...........................................................................................................3
What Is Included ........................................................................................................................3
Unpacking Instructions...............................................................................................................3
Claims ..............................................................................................................................................3
Text Conventions .......................................................................................................................3
Icons..........................................................................................................................................3
Disclaimer..................................................................................................................................3
Product at a Glance ...................................................................................................................4
Safety Notes ..............................................................................................................................4
2. Introduction ....................................................................................................................5
Product Overview.......................................................................................................................5
Product Dimensions ...................................................................................................................6
3. Setup...............................................................................................................................7
AC Power ..................................................................................................................................7
Power Linking ...................................................................................................................................7
Mounting....................................................................................................................................8
Orientation ........................................................................................................................................8
Rigging .............................................................................................................................................8
4. Operation ........................................................................................................................9
Control Panel Operation.............................................................................................................9
Menu Map..................................................................................................................................9
Configuration (DMX) ................................................................................................................10
DMX Personalities and Starting Address ......................................................................................... 10
DMX Channel Assignments and Values ...................................................................................11
3-CH............................................................................................................................................... 11
4-CH............................................................................................................................................... 11
5-CH............................................................................................................................................... 11
DMX Channel Assignments and Values (cont.) ........................................................................12
9-CH............................................................................................................................................... 12
Configuration (Standalone).......................................................................................................13
Automatic Mode .............................................................................................................................. 13
Static Color Mode............................................................................................................................ 13
Custom Static Color Mode ...............................................................................................................13
Dimmer Adjustment ......................................................................................................................... 13
Touch Control Panel Lock................................................................................................................ 14
Master/Slave Mode ......................................................................................................................... 14
5. Technical Information ..................................................................................................15
Product Maintenance ...............................................................................................................15
6. Technical Specifications..............................................................................................16
Returns ....................................................................................................................................17
Contact Us...............................................................................................................................17

SlimPANEL™ TRI 24 IP User Manual (Rev. 4) Page 3 of 17
1. BEFORE YOU BEGIN
What Is
Included
•SlimPANEL™ TRI 24 IP
•DMX In Adapter
•DMX Out Adapter
•Power Cord
•Warranty Card
•Quick Reference Guide
Unpacking
Instructions
Immediately upon receipt, carefully unpack the product and check the box to make sure
you have received all the parts indicated above in good condition.
Claims
If the box or the contents (the product and
included accessories) appear damaged from
shipping, or show signs of mishandling, upon receipt notify the carrier immediately, not
CHAUVET®.
Failure to do so in a timely manner may invalidate your claim with the
carrier. In addition, keep the container and all the packing material for inspection.
For other issues such as missing components or parts, damage not relat
ed to shipping,
or concealed damage, file a claim with CHAUVET® within 7 days of receiving the
merchandise.
Text
Conventions
Convention Meaning
1–512
A range of values
50/60
A set of values of which only one can be chosen
Settings
A menu option not to be modified
Menu > Settings
A sequence of menu options to be followed
<ENTER>
A key to be pressed on the product’s control panel
ON
A value to be entered or selected
Symbols
Symbol Meaning
Critical installation, configuration, or operation information. Failure
to comply with this information may cause the product to not work,
damage it, or cause harm to the operator.
Important installation or configuration information. Failure to
comply with this information may prevent the product from working
properly.
Useful information.
Disclaimer
The information and specifications contained in this document are subject to change
without notice. CHAUVET® assumes no responsibility or liability for any errors or
omissions that may appear in this manual.
CHAUVET® reserves the right to update the
existing document or to create a new document to correct any errors or omissions.
You can download the latest version of this document from www.chauvetlighting.com.
© Copyright 2013 CHAUVET®. All rights reserved.
Electronically published by CHAUVET® in the United States of America.
Author
Date
Editor
Updated
A. Diaz 6/18/12 S. Diaz 1/23/13

Page 4 of 17 SlimPANEL™ TRI 24 IP User Manual (Rev. 4)
Product at a
Glance
Use on Dimmer

Auto Programs

Outdoor Use

Auto-ranging Power Supply

Sound Activated

Replaceable Fuse

DMX

User Serviceable

Master/Slave

Duty Cycle

Safety Notes
Please read the following Safety Notes carefully before working with the product. The
Notes include important safety information about installation, usage, and maintenance.
•Always connect the product to a GFI (ground fault interrupter) circuit to avoid the
risk of electrocution.
•Always disconnect the product from the power source before cleaning.
•Avoid direct eye exposure to the light source while the product is on.
•Make sure the power cord is not crimped or damaged.
•Never disconnect the product from power cord by pulling or tugging on the cord.
•If mounting the product overhead, always secure to a fastening device using a
safety cable.
•Make sure there are no flammable materials close to the product when operating.
•
Do not touch the product’s housing when operating because it may be very hot.
•Always make sure that the voltage of the outlet to which you are connecting the
product is within the range stated on the decal or rear panel of the product.
•The product is for indoor or outdoor use (IP65!). Do not submerge the product.
•Always install the product in a location with adequate ventilation, at least 20 in (50
cm) from adjacent surfaces.
•Be sure that no ventilation slots on the product’s housing are blocked.
•Never connect the product to a dimmer.
•Make sure to replace the fuse with another of the same type and rating.
•Never carry the product from the power cord or any moving part. Always use the
hanging/mounting bracket or the handles.
•The maximum ambient temperature (Ta) is 104° F (40° C). Do not operate the
product at higher temperatures.
•In the event of a serious operating problem, stop using the product immediately.
•Never try to repair the product. Repairs carried out by unskilled people can lead to
damage or malfunction. Please contact the nearest authorized technical assistance
center.
•Keep this User Manual for future consultation. If you sell the product to another
user, be sure that they also receive this document.

SlimPANEL™ TRI 24 IP User Manual (Rev. 4) Page 5 of 17
2. INTRODUCTION
Product Overview
Touch Display
Power Out
DMX Out
Power In
DMX In
Mounting Bracket

Page 6 of 17 SlimPANEL™ TRI 24 IP User Manual (Rev. 4)
Product Dimensions

SlimPANEL™ TRI 24 IP User Manual (Rev. 4) Page 7 of 17
3. SETUP
AC Power
The SlimPANEL™ TRI 24 IP has an auto-
ranging power supply and it can work with an
input voltage range of 100–240 VAC, 50/60 Hz.
To determine the product’s power requirements (circuit breaker, power outlet, and
wiring), use the current value listed on the label affixed to the product’s back panel, or
refer to the product’s specifications chart. The listed current rating indicates the
product’s average current draw under normal conditions.
Always connect the product to a protected circuit
(circuit breaker or fuse). Make
sure the product has
an appropriate electrical ground to avoid the risk of
electrocution or fire.
Never connect the product to
a rheostat (variable resistor) or dimmer circuit, even
if the rheostat or dimmer channel serves only as a 0 to 100% switch.
Power Linking The
product provides a power linking option via the pigtails located on the back of the
unit.
You can daisy chain up to 6 units on 120 VAC or up to 12 units on 230 VAC.
If you choose not to use the power linking feature, be sure to use the included screw on
cap to prevent any water from getting into the power cords.
The power linking information above corresponds
to the North American version
of the product ONLY! If using the product
in other markets, you must consult with
the local CHAUVET® distributor as power linking connectors and requirements
may differ in your country or region.

Page 8 of 17 SlimPANEL™ TRI 24 IP User Manual (Rev. 4)
Mounting
Before mounting the product
, read and follow the safety recommendations indicated in
the Safety Notes.
Orientation
The SlimPANEL™ TRI 24 IP
may be mounted in any position; however, make sure
adequate ventilation is provided around the product.
Rigging
•Before deciding on a location for the product, always make sure there is easy
access to the product for maintenance and programming purposes.
•Make sure that the structure onto which you are mounting the product
can support
the product’s weight. Please see the Technical Specifications
section of this manual
for weight information.
•When mounting the product overhead, always use a safety cable.
Mount the
product securely to a rigging point, whether an elevated platform or a truss.
•When rigging the product onto a truss, you should use a mounting clamp of
appropriate weight capacity. The bracket has a 13 mm hole, which is appropriate for
this purpose.
•When power linking multiple products, you must always consider the length of the
power linking cable and mount the products close enough for the cable to reach.
Mounting Diagram
Bracket Adjustment
Mounting Bracket

SlimPANEL™ TRI 24 IP User Manual (Rev. 4) Page 9 of 17
4. OPERATION
Control Panel
Operation
To access the control panel functions,
use the four buttons located underneath the
display. Please refer to the Product Overview to see the button locations
on the control
panel.
Button Function
<MENU> Press to find an operation mode or to back out of the current menu
option
<UP> Press to scroll up the list of options or to find a higher value
<DOWN> Press to scroll down the list of options or to find a lower value
<ENTER> Press to activate a menu option or a selected value
Menu Map
Mode
Programming Steps
Description
DMX Address Addr d__1-d512 Selects DMX starting address
DMX
Personalities PRES
3CH
Selects DMX personality
4CH
5CH
9CH
Dimmer DIM
OFF
Change dimmer speed
DIM1
DIM2
DIM3
Static Color C--
C1 Red
C2 Green
C3 Blue
C4
Cyan
C5 Magenta
C6 Yellow
C7 White
Touch Control
Panel Lock PASS
ON Locks touch control panel
Password is
UP,DOWN,UP,DOWN,ENTER
OFF
Custom Color
Mixing U--
r--
Red
g-- Green
b-- Blue
S-- Strobe rate
Auto Programs P--
P1
S__1-
S100
Auto program selection and speed
selection
P2
P3
P4
P5

Page 10 of 17 SlimPANEL™ TRI 24 IP User Manual (Rev. 4)
Configuration
(DMX)
Set the product in DMX mode to control with a DMX controller.
1. Connect the product to a suitable power outlet.
2. Turn the product on.
3.
Connect a DMX cable from the DMX output of the DMX controller to the DMX input
socket on the product.
DMX
Personalities
and
Starting
Address
The SlimPANEL™ TRI 24 IP has 4 DMX personalities, from a 3-
channel mode for basic
control to a 9-channel mode with more advanced control over the lights.
The SlimPANEL™ TRI 24 IP uses up to 9 DMX channels in its 9-
channel DMX mode,
which defines the highest configurable address to 504.
When selecting a starting DMX address, always consider the number of DMX channels
the selected DMX mode uses. If you choose a starting address that is too high, you could
restrict the access to some of the product’s channels.
If you are not familiar with the DMX protocol, download the DMX Primer at
www.chauvetlighting.com.
To select the DMX personality, do the following:
1. Press <MENU> repeatedly until PERS shows on the display.
2. Use <UP> or <DOWN> to select 3CH, 4CH, 5CH or 9CH.
3. Press <ENTER> to choose your DMX personality when it appears on the display.
To then choose your starting address:
1. Press <MENU> repeatedly until Addr shows on the display.
2. Use <UP> or <DOWN> to select the starting address.
4. Press <ENTER>.

SlimPANEL™ TRI 24 IP User Manual (Rev. 4) Page 11 of 17
DMX Channel Assignments and Values
3-CH
Channel Function Value Setting
1
Red
000 255
0–100%
2
Green
000 255
0–100%
3
Blue
000

255
0–100%
4-CH
Channel Function Value Setting
1
Dimmer
000 255
0–100%
2
Red
000 255
0–100%
3
Green
000 255
0–100%
4
Blue
000 255
0–100%
5-CH
Channel Function Value Setting
1
Red
000 255
0–100%
2
Green
000 255
0–100%
3
Blue
000 255
0–100%
4
Dimmer
000 255
0–100%
5 Strobe
000 010
No function
011 255
Slow to fast

Page 12 of 17 SlimPANEL™ TRI 24 IP User Manual (Rev. 4)
DMX Channel Assignments and Values (cont.)
9-CH
Channel Function Value Setting
1
Dimmer
000 255
0–100%
2
Red
000 255
0–100%
3
Green
000 255
0–100%
4
Blue
000 255
0–100%
5 Color Macros
000 010
No function
011 200
Color Macros
201 205
White 1: 3200K
206 210
White 2: 3400K
211 215
White 3: 4200K
216

220
White 4: 4900K
221 225
White 5: 5600K
226 230
White 6: 5900K
231 235
White 7: 6500K
236 240
White 8: 7200K
241 245
White 9: 8000K
246 250
White 10: 8500K
251 255
White 11: 10000K
6 Strobe
000 009
No function
010 255
0–100% (slow to fast)
7 Auto Programs
000 051
No function
052 101
Auto Program 1
102 152
Auto Program 2
153 203
Auto Program 3
204 254
Auto Program 4
255
Auto Program 5
8
Auto Program Speed
000 255
Slow to fast (when Ch. 7 is 052–255)
9 Dimmer Curve
000 051
Default speed
052 101
Linear dimmer
102 152
Nonlinear dimmer 1
153 203
Nonlinear dimmer 2
204 255
Nonlinear dimmer 3

SlimPANEL™ TRI 24 IP User Manual (Rev. 4) Page 13 of 17
Configuration
(Standalone)
Set the product in one of the standalone modes to control without a DMX controller.
1. Connect the product to a suitable power outlet.
2. Turn the product on.
Never connect a product
that is operating in any standalone mode to a DMX string
connected to a DMX controller. Products in standalone mode may transmit DMX
signals that could interfere with the DMX signals from the controller.
Automatic Mode
To enable the Automatic Mode, follow the instructions below:
1. Press <MENU> repeatedly until P-- shows on the display.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to choose an auto program (P1-P5).
4. Press <ENTER> to adjust the speed of the program.
5. Use <UP> or <DOWN> to adjust the duration of each step of the automatic program
from S__1 (fast) to S100 (slow).
6. Press <ENTER>.
Static Color Mode
To enable the Static Color Mode, follow the instructions below:
1. Press <MENU> repeatedly until C-- shows on the display.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to choose a color (C1-C7).
4. Press <ENTER>.
Custom Static
Color Mode
To enable the Custom Static Color Mode, follow the instructions below:
1. Press <MENU> repeatedly until U-- shows on the display.
2. Press <ENTER> to choose between colors (r--, g--, b--).
3. Press <UP> or <DOWN> to choose the intensity of the color (000-100).
4. Repeat the steps to mix additional colors to create the color you need.
5. Press <ENTER>.
You can also manually adjust the strobe rate. To do so, do the following:
1. Press <MENU> repeatedly until U-- shows on the display.
2. Press <ENTER> until S-- shows on the display.
3. Press <UP> or <DOWN> to choose the strobe rate (S 0-S 20).
4. Press <ENTER> once you have chosen your desired strobe rate.
Dimmer
Adjustment
You can manually control the dimmer speed to suit any need. To set up your preferred
dimmer speed, do the following:
1. Press <MENU> repeatedly until DIM shows on the display.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to choose between the dimming types (OFF-DIM3).
4. Press <ENTER>.

Page 14 of 17 SlimPANEL™ TRI 24 IP User Manual (Rev. 4)
Touch Control
Panel Lock
To enable the touch panel lock, follow the instructions below:
1. Press <MENU> repeatedly until PASS shows on the display.
2. Press <ENTER>.
3. Press <UP> or <DOWN> until ON
shows on the display to enable the touch panel
lock.
To disable the touch panel lock so you can resume functionality, follow the steps below:
1. Press <UP>, <DOWN>, <UP>, <DOWN>, <ENTER>
to disable the touch panel
lock.
2. Press <MENU> to move through the menus as normal.
In situations where water may flow onto the touch display, use the Touch Panel Control
Lock so that the water does not reset the product’s settings.
Master/Slave
Mode
The Master/Slave mode allows a single SlimPANEL™ TRI 24 IP unit (the “master”) to
control the actions of one or more SlimPANEL™ TRI 24 IP
units (the “slaves”) without
the need of a DMX controller. The master unit will be set to operate
in a standalone
mode, while the slave units will be set to operate in Slave Mode. Once set and
connected, the slave units will operate in unison with the master unit.
Configure the units as indicated below.
Slave units:
1. Press <MENU>repeatedly until Addr shows on the display.
2. Press <ENTER> to accept.
3. Set the DMX address to 001.
4. Connect the DMX input of the first slave unit to the DMX output of the master unit.
5.
Connect the DMX input of the subsequent slave units to the DMX output of the
previous slave unit.
6. Finish setting and connecting all the slave units.
Master unit:
1. Set the master unit to operate in standalone mode.
2. Make the master unit the first unit in the daisy chain.
•Configure
all the slave units before connecting the master unit to the daisy
chain.
•
Never connect a DMX controller to a DMX string configured for Master/Slave
operation because the controller
may interfere with the signals from the
master unit.
•Do not connect more than 31 slave units to the master unit.

SlimPANEL™ TRI 24 IP User Manual (Rev. 4) Page 15 of 17
5. TECHNICAL INFORMATION
Product
Maintenance
Dust build-
up reduces light output performance and can cause overheating. This can
lead to reduction of the light source’s life.
To maintain optimum performance and
minimize wear, you should clean your lighting products at least twice a month. However,
use and environmental conditions contribute to increased cleaning frequency.
To clean the product, follow the instructions below:
•Unplug the product from power.
•Wait until the product is cold.
•Use a vacuum (or dry compressed air) and a soft brush to remove dust collected on
the external surface/vents.
•Clean all external optics and glass/transparent surfaces with a mild soap solution,
ammonia-free glass cleaner, or isopropyl alcohol.
•Apply the solution directly to a soft, lint free cotton cloth or a lens cleaning tissue.
•Softly drag any dirt or grime to the outside of the external optics or glass/transparent
surface.
•Gently polish the external optics and glass/transparent surfaces until they are free of
haze and lint.
Always dry the external optics and glass/transparent
surfaces carefully after
cleaning them.

Page 16 of 17 SlimPANEL™ TRI 24 IP User Manual (Rev. 4)
6. TECHNICAL SPECIFICATIONS
Dimensions and
Weight
Length
Width
Height
Weight
10.5 in (268 mm)
11.9 in (301 mm)
5.3 in (134 mm)
13.8 lbs (6.2 kg)
Note: Dimensions in inches rounded to the nearest decimal digit.
Power
Power Supply Type
Range
Voltage Selection
Switching (internal)
100–240 V, 50/60 Hz
Auto-ranging
Parameter
120 V, 60 Hz
230 V, 50 Hz
Consumption
137 W
146 W
Operating
1.2 A
0.6 A
Power linking current (units)
8 A (6 units)
8 A (12 units)
Fuse
F 2 A, 250 V
F 2 A, 250 V
Power I/O
U.S./Worldwide
UK/Europe
Power input connector
Proprietary
Proprietary
Power output connector
Proprietary
Proprietary
Power Cord plug
Edison (U.S.)
Local plug
Light Source
Type
Power
Lifespan
LED
3 W
50,000 hours
Color
Quantity
Current
Tri-color
24
350 mA (x3)
Photo Optic
Parameter
Illuminance @ 2 m
5,850 lux
Beam angle
20º
Field angle
34°
Thermal
Maximum External Temp.
Minimum Startup Temp.
Cooling System
113° F (45° C)
-4° F (-20° C)
Convection
DMX
I/O Connectors
Connector Type
Channel Range
3-pin XLR
Proprietary
3, 4, 5, 9
Ordering
Product Name
Item Code
Item Number
SlimPANEL™ TRI 24 IP
03030532
SLIMPANELTRI24IP

SlimPANEL™ TRI 24 IP User Manual (Rev. 4) Page 17 of 17
In case you need to return a product or request support:
•If you live in the U.S., contact CHAUVET® World Headquarters (see below).
•If you live in the UK or Ireland, contact CHAUVET® Europe Ltd. (see below).
•If you live in any other country, DO NOT contact CHAUVET®. Instead, contact your
distributor of record. See www.chauvetlighting.com for distributors outside the U.S.,
United Kingdom, or Ireland.
If you live outside the U.S., United Kingdom, or Ireland, contact your distributor of
record and follow their instructions on how to return CHAUVET® product
s to
them. Visit our website for contact details.
Returns
Call the corresponding CHAUVET®
Tech Support office and request a Return
Merchandise Authorization (RMA) number before shipping the product
. Be prepared to
provide the model number, serial number, and a brief description of the
cause for the
return.
You must send the merchandise prepaid, in its original box, and with its original packing
and accessories. CHAUVET® will not issue call tags.
Clearly label the package with the RMA number. CHAUVET® will refuse any product
returned without an RMA number.
Write the RMA number on a properly affixed label. DO NOT write the RMA number
directly on the box.
Before sending the product, clearly write
the following information on a piece of paper
and place it inside the box:
•Your name
•Your address
•Your phone number
•The RMA number
•A brief description of the problem
Be sure to pack the product
properly. Any shipping damage resulting from inadequate
packaging will be your responsibility. As a suggestion, proper UPS packing or double-
boxing is always a safe method to use.
CHAUVET®
reserves the right to use its own discretion to repair or replace
returned product(s).
Contact Us
World Headquarters
CHAUVET®
General Information
Address: 5200 NW 108th Avenue
Sunrise, FL 33351
Voice: [phone]
Fax: [phone]
Toll free: [phone]
United Kingdom & Ireland
CHAUVET® Europe Ltd.
General Information
Address: Unit 1C
Brookhill Road Industrial Estate
Pinxton, Nottingham, UK
NG16 6NT
Voice: [phone]
Fax: [phone]
Technical Support
Voice: [phone] (Press 4)
Fax: [phone]
Email: [e-mail]
Technical Support
Email: [e-mail]
World Wide Web
www.chauvetlighting.com
World Wide Web
www.chauvetlighting.co.uk