Chauvet Scorpion BURST GB User manual

LASER LIGHT
AVOID DIRECT EYE EXPOSURE
CLASS IIIa LASER PRODUCT
CLASSIFIED PER 21 CFR 1040.10 & .11
Complies with US FDA CDRH laser safety
standards 21 CFR 1040.10 & 1040.11.
User Manual

Table of Contents
1. BEFORE YOU BEGIN .............................................................................................................................................. 4
LASER SAFETY LABEL REPRODUCTION......................................................................................................................7
LASER EMISSION DATA...........................................................................................................................................8
LASER COMPLIANCE STATEMENT ............................................................................................................................8
2. INTRODUCTION ...................................................................................................................................................... 9
OVERVIEW............................................................................................................................................................9
DIMENSIONS .........................................................................................................................................................9
3. SETUP ............................................................................................................................................................... 11
ACPOWER ........................................................................................................................................................ 11
FUSE REPLACEMENT............................................................................................................................................ 11
MOUNTING ......................................................................................................................................................... 11
Orientation........................................................................................................................................................................................11
Rigging .............................................................................................................................................................................................11
4. OPERATION ........................................................................................................................................................ 13
Changing Options Within the Same Function................................................................................................................................13
Changing Options for a Different Function......................................................................................................................................13
MENU MAP......................................................................................................................................................... 13
Starting Address...............................................................................................................................................................................14
Sound-Active Mode..........................................................................................................................................................................14
Automatic Mode...............................................................................................................................................................................14
Master/Slave Mode..........................................................................................................................................................................14
REMOTE CONTROL .............................................................................................................................................. 15
DMX VALUES ..................................................................................................................................................... 16
DMX VALUES (CONTINUED) .................................................................................................................................. 17
DMX VALUES AND PATTERN LIST .......................................................................................................................... 17
5. TECHNICAL INFORMATION ..................................................................................................................................... 18
6. TECHNICAL SPECIFICATIONS ................................................................................................................................. 19
1. ANTES DE EMPEZAR............................................................................................................................................. 21
REPRODUCCIÓN DE LA ETIQUETA DE SEGURIDAD DEL LÁSER ...................................................................................... 24
DATOS DE EMISIÓN LÁSER .................................................................................................................................... 25
DECLARACIÓN DE CONFORMIDAD LÁSER ................................................................................................................ 25
2. INTRODUCCIÓN.................................................................................................................................................... 26
VISTA GENERAL .................................................................................................................................................. 26
DIMENSIONES ..................................................................................................................................................... 26
3. INSTALACIÓN ...................................................................................................................................................... 28
CORRIENTE ALTERNA........................................................................................................................................... 28
SUSTITUCIÓN DEL FUSIBLE.................................................................................................................................... 28
MONTAJE ........................................................................................................................................................... 28
Orientación.......................................................................................................................................................................................28
Colocación........................................................................................................................................................................................28
4. FUNCIONAMIENTO................................................................................................................................................ 30
Cambiar Opciones Dentro de la Misma Función............................................................................................................................30
Cambiar Opciones para una Función Diferente .............................................................................................................................30
MAPA DE MENÚ................................................................................................................................................... 30
Dirección de Inicio............................................................................................................................................................................31
Modo Activo por Sonido...................................................................................................................................................................31
Modo Automático.............................................................................................................................................................................31
Modo Maestro/Esclavo ....................................................................................................................................................................32
CONTROL REMOTO.............................................................................................................................................. 33
VALORES DMX................................................................................................................................................... 34
VALORES DMX (CONTINUACIÓN)............................................................................................................................ 35
VALORES DMX Y LISTA DE PATRONES.................................................................................................................... 35
5. INFORMACIÓN TÉCNICA......................................................................................................................................... 36
6. ESPECIFICACIONES TÉCNICAS ............................................................................................................................... 37
1. AVANT DE COMMENCER........................................................................................................................................ 39
REPRODUCTION DES ETIQUETTES EN MATIERE DE SECURITE DES APPAREILS LASER...................................................... 42
DONNEES D'EMISSION LASER ................................................................................................................................ 43

DECLARATION DE CONFORMITE DU LASER .............................................................................................................. 43
2. INTRODUCTION .................................................................................................................................................... 44
APERÇU............................................................................................................................................................. 44
DIMENSIONS ....................................................................................................................................................... 44
3. CONFIGURATION.................................................................................................................................................. 46
ALIMENTATION CA............................................................................................................................................... 46
REMPLACEMENT DU FUSIBLE................................................................................................................................. 46
INSTALLATION ..................................................................................................................................................... 46
Orientation........................................................................................................................................................................................46
Suspension.......................................................................................................................................................................................46
4. FONCTIONNEMENT ............................................................................................................................................... 48
Changer d'Options au Sein d'Une Même Fonction .......................................................................................................................48
Changer d'Options au Sein d'Une Fonction Différente...................................................................................................................48
TABLEAU DU MENU .............................................................................................................................................. 48
Adresse de Départ...........................................................................................................................................................................49
Mode Musical...................................................................................................................................................................................49
Mode Automatique...........................................................................................................................................................................49
Mode Maître/Esclave.......................................................................................................................................................................50
TELECOMMANDE.................................................................................................................................................. 51
VALEURS DMX ................................................................................................................................................... 52
VALEURS DMX (SUITE) ........................................................................................................................................ 53
VALEURS DMX ET LISTE DE MOTIFS....................................................................................................................... 53
5. INFORMATIONS TECHNIQUES ................................................................................................................................. 54
6. SPECIFICITES TECHNIQUES ................................................................................................................................... 55

Rev. 2 4 Scorpion™ Burst GB User Manual
1.Before You Begin
What Is
Included
•Scorpion™ Burst GB
•Power Cord
•Infrared Remote Control (IRC)
•Warranty Card
•User Manual
Claims
Immediately unpack and check the box. Make sure all the parts are present and in
good condition. If the material inside the box appears damaged from shipping, notify
the shipper immediately, not CHAUVET®. In addition, retain the container and all the
packing material for inspection.
For other issues such as missing components or parts, damage not related to
shipping, or concealed damage, file a claim with CHAUVET® within
7 days of
receiving the merchandise.
Text
Conventions
Convention
Meaning
<Menu>
A key to be pressed on the product’s control panel
1~512
A range of values
50/60
A set of values of which only one can be chosen
Settings
A menu option not to be modified (for example, showing
the operating mode/current status)
MENU > Settings
A sequence of menu options to be followed
ON
A value to be entered or selected
Symbols
Symbol
Meaning
Critical installation, configuration, or operation information.
Ignoring this information can cause the product to not work,
damage it, or cause harm to the operator.
Important installation or configuration information. The
product may not function correctly if this information is not
used.
Useful information.
Disclaimer
The information and specifications contained in this document are subject to change without
notice. CHAUVET® assumes no responsibility or liability for any errors or omissions that may
appear in this manual. © Copyright 2012 CHAUVET®. All rights reserved.
Printed in P.R.C. Electronically published by CHAUVET® in the U.S.A.
Author Date
S. Diaz 10/29/12

Scorpion™ Burst GB User Manual 5 Rev. 2
Safety Notes
CAUTION! The use of optical instruments with this product will increase eye
hazard.
Please read the following notes carefully because they include important safety
information about the installation, usage, and maintenance of this product.
•CAUTION! Viewing laser light directly (intra-beam viewing) through optical
instruments, such as cameras and binoculars, may increase risks to the eyes.
•Lasers can be hazardous and have unique safety considerations. Permanent eye
injury and blindness is possible if lasers are used incorrectly. Pay close attention
to each safety REMARK and WARNING statement in this User Manual. Read all
instructions carefully BEFORE operating this device.
•Keep this User Manual for future consultation. If you sell this product to another user,
be sure that they also receive this document.
•Always make sure that the voltage of the outlet to which you are connecting this
product is within the range stated on the decal or rear panel of the product.
•
This product is for indoor use only! To prevent risk of fire or shock, do not expose this
product to rain or moisture.
•Make sure there are no flammable materials close to the unit while operating.
•Always install this product in a location with adequate ventilation, at least 20 in (50
cm) from adjacent surfaces. Be sure that no ventilation slots are blocked.
•Always disconnect this product from the power source before cleaning it or replacing
fuse.
•Make sure to replace the fuse with another of the same type and rating.
•If mounting it overhead, always secure this product to a fastening device using a
safety chain.
•The maximum ambient temperature (Ta) is 104° F (40° C). Do not operate this
product at higher temperatures.
•In the event of a serious operating problem, stop using the unit immediately. Never
try to repair the unit. Repairs carried out by unskilled people can lead to damage or
malfunction. Please contact the nearest authorized technical assistance center.
•Never connect this product to a dimmer pack or rheostat.
•Make sure the power cord is not crimped or damaged.
•Never disconnect the power cord by pulling or tugging on the cord.
•Never carry a product from the power cord or any moving part. Always use the
hanging/mounting bracket or the handles.
•Always avoid direct eye exposure to the light source when this product is on.
•Lasers can be hazardous and have unique safety considerations. Permanent eye
injury and blindness is possible if lasers are used incorrectly. Pay close attention to
each safety REMARK and WARNING statement in this user manual. Read all
instructions carefully BEFORE operating this device.
•Avoid direct eye contact with laser light. Never intentionally expose your eyes or
others to direct laser light.
•This laser product can potentially cause instant eye injury or blindness if laser
light directly strikes the eyes.
•It is illegal and dangerous to shine this laser into audience areas, where the
audience or other personnel could get direct laser beams or bright reflections
into their eyes.
•It is a U.S. federal offense to shine any laser at aircraft.
•Use of controls or adjustments or performance of procedures other than those
specified herein may result in hazardous radiation exposure.
•There are no user-serviceable parts inside the unit. Do not open the housing or
attempt any repairs yourself. In the unlikely event your unit may require service,
please contact the dealer nearest to you.

Rev. 2 6 Scorpion™ Burst GB User Manual
Non-
Interlocked
Housing
Warning
•This unit contains high-power laser devices internally.
•Do not open the laser housing because of potential exposure to unsafe levels of
laser radiation.
•The laser power levels, accessible if the unit is opened, can cause instant
blindness, skin burns, and fires.
Laser Safety
Notes
STOP AND READ ALL THE LASER SAFETY NOTES BELOW
Laser light is different from any other light sources with which you may be familiar. The
light from this product can potentially cause eye injury if not set up and used properly.
Laser light is thousands of times more concentrated than light from any other kind of light
source. This concentration of light can cause instant eye injuries, primarily by burning the
retina (the light sensitive portion at the back of the eye). Even if you cannot feel “heat” from
a laser beam, it can still potentially injure or blind you or your audience. Even very small
amounts of laser light are potentially hazardous even at long distances. Laser eye injuries
can happen quicker than you can blink.
It is incorrect to think that because these laser entertainment products split the laser into
dozens of beams and the laser beams are scanned out in high speed, that an individual
laser beam is safe for eye exposure. This laser product uses dozens of milliwatts of laser
power (Class 3B levels internally) before it splits into multiple beams (Class IIIa levels).
Many of the individual beams are potentially hazardous to the eyes.
It is also incorrect to assume that because the laser light is moving, it is safe. This is not
true. Nor, do the laser beams always move. Since eye injuries can occur instantly, it is
critical to prevent the possibility of any direct eye exposure. In the laser safety regulation, it
is not legal to aim Class IIIa
lasers in areas which people can get exposed. This is true
even if it is aimed below people’s faces, such as on a dance floor.
•Do not operate the laser without first reading and understanding all safety and technical
data in this manual.
•Always set up and install all laser effects so that all laser light is at least 3meters (9.8 feet)
above the floor on which people can stand. See “Proper Usage” section later in this
manual.
•After set up, and prior to public use, test laser to ensure proper function. Do not use if any
defect is detected.
•DO NOT use if laser lens is damaged or missing, as this could indicate damage to the
diffraction grating optic, and could allow emission of higher laser levels above Class IIIa.
•Do not use laser if the laser appears to be emitting only one or two beams.
•Do not point lasers at people or animals.
•Never look into the laser aperture or laser beams.
•Do not point lasers in areas in which people can potentially get exposed, such as
uncontrolled balconies, etc.
•Do not point lasers at highly reflective surfaces, such as windows, mirrors, and shiny metal.
Even laser reflections can be hazardous.
•Never point a laser at aircraft; this is a federal offense.
•Never point un-terminated laser beams into the sky.
•Do not expose the output optic (aperture) to cleaning chemicals.
•Do not use the laser if the housing is damaged, open, or if the optics appear damaged in
any way.
•Never open the laser housing. The high laser power levels inside the protective housing
can start fires, burn skin, and will cause instant eye injury.
•Never leave this device running unattended.
•The operation of a Class IIIa laser show is only allowed if the show is controlled by a skilled
and well-trained operator, familiar with the data included in this manual.
•The legal requirements for using laser entertainment products vary from country to country.
The user is responsible for the legal requirements at the location/country of use.
•
Always use appropriate lighting safety cables when hanging lights and effects overhead.

Scorpion™ Burst GB User Manual 7 Rev. 2
Laser Safety Label Reproduction
LASER HAZARD
WARNING LABEL
LASER APERTURE LABEL
EXPLANATORY,
MANUFACTURER’S ID, &
CERTIFICATION LABEL
NON-INTERLOCKED
HOUSING LABEL

Rev. 2 8 Scorpion™ Burst GB User Manual
Laser light - Avoid direct eye contact!
Further guidelines and safety programs for safe use of lasers can be found in the ANSI Z136.1
Standard “For Safe Use of Lasers,” available from the Laser Institute of America:
www.laserinstitute.org. Many local governments, corporations, agencies, military, and others, require
all lasers to be used under the guidelines of ANSI Z136.1. Laser Display guidance can be obtained
via the International Laser Display Association: www.laserist.org.
Laser Emission Data
LASER CLASSIFICATION Class IIIa
Green Laser Diode DPSS Nd:YVO4, 532 nm
Blue Laser Diode LD GaN 450 nm, typical
Beam Diameter <5mm at aperture
Pulse Data 100 msec to CW (continuous)
Divergence (each beam) <2 mrad
Scan Angle <160 degrees
Peak Power for
Classification <5 MW
Laser Compliance Statement
This laser product complies with U.S. FDA CDRH laser safety standards 21 CFR
1040.10 & 1040.11. This laser device is classified Class IIIa. No maintenance is
required to keep this product in compliance with laser performance standards.
LASER EXPOSURE

Scorpion™ Burst GB User Manual 9 Rev. 2
2.Introduction
Overview
Mounting Bracket
Bracket Adjustment Knob
Laser Aperture
DMX In/Out
Power In
Fuse Holder
Safety Loop
Display Panel
Power Out
Cooling Fan
Power Switch

Rev. 2 10 Scorpion™ Burst GB User Manual
Dimensions

Scorpion™ Burst GB User Manual 11 Rev. 2
The fuse is located
inside this
compartment.
Remove using a
flat-head screwdriver.
3. Setup
AC Power
This product has an auto-ranging power supply and can work with an input voltage range of
100~240 VAC, 50/60 Hz. See the label affixed to the back plate of the product or refer to the
specifications chart. The listed current rating indicates its average current draw under normal
conditions.
Always connect the product to a switched circuit. Never connect the product to a rheostat
(variable resistor) or dimmer circuit, even if the rheostat or dimmer channel is used only
as a 0% to 100% switch.
Fuse Replacement
With a flat-head screwdriver, wedge the fuse holder
out of its housing. Remove the damaged fuse from
its holder and replace with exact same type of fuse.
Insert the fuse holder back in its place and
reconnect power.
Disconnect from power before replacing a fuse. Always replace with a fuse of the same
type and rating.
Mounting
Orientation The Scorpion™ Burst GB may be mounted in any safe position, provided there is adequate room
for ventilation.
Rigging Be sure that the structure onto which you are mounting this product can support its weight. See the
Technical Specifications section of this manual for weight information. Mount the product securely.
You can do this with a screw, a nut, and a bolt. You could also use a mounting clamp if rigging this
product onto a truss. Always use a safety cable. Consider ease of access to the unit for
maintenance and programming purposes before deciding on a location for this product.
When power linking multiple products, always consider the length of the power linking cable and
mount the products close enough together for cables to reach.
The bracket adjustment knobs allow for aiming the product to a desired angle. Do not use tools to
loosen or tighten the bracket knobs because tools can damage them.
Mounting clamp
Safety loop/
Safety cable

Rev. 2 12 Scorpion™ Burst GB User Manual
Proper
Usage
This product is for overhead mounting only. For safety purposes, CHAUVET®
recommends mounting your lighting effect products on steady elevated platforms or
sturdy overhead supports using suitable hanging clamps. In all cases, you must use
safety cables. You can obtain appropriate mounting hardware from your distributor.
International laser safety regulations require that laser products must be operated in
the fashion illustrated below, with a minimum of 3 meters (9.8 ft) of vertical separation
between the floor and the lowest laser light vertically. Additionally, 2.5 meters of
horizontal separation is required between laser light and audience or other public
spaces.
CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF
PROCEDURES OTHER THA
N THOSE SPECIFIED HEREIN MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE.

Scorpion™ Burst GB User Manual 13 Rev. 2
4. Operation
Control
Panel
Operation
To access the control panel functions, use the four buttons located underneath the
display.
Button Function
<MENU>
Press to find an operation mode or to back out of the current menu
option
<UP>
Press to scroll up the list of options or to find a lower value
<DOWN>
Press to scroll down the list of options or to find a higher value
<ENT>
Press to activate a menu option or a selected value
The control panel will remember the last setting you programmed, even after
you have turned the product off.
Changing
Options Within
the Same
Function
To change an option, do the following:
1. Press <MENU> once (the LED display will blink).
2. Press <UP> or <DOWN> until the desired menu option shows on the LED
display.
3. Press <ENT> to accept the new option (the new option will show solid on the
LED display).
Changing
Options for a
Different
Function
To change an option for a different function:
1. Press <MENU> once (the LED display will blink).
2. Press <MENU> repeatedly until seeing the active option of the desired menu
branch.
3. Press <UP> or <DOWN> until the desired menu option within the new menu
branch shows on the LED display.
4. Press <ENT> to accept the new option (the new option will show solid on the
LED display).
Menu Map
Mode or Starting
Value
Program or
Channel Range
Options Description
Standalone
Aut
Pre-programmed effects that cannot be customized
Aut
N/A
Automatic (Random)
Au1
N/A
Auto Blue
Au2
N/A
Auto Green
Au3
N/A
Auto Green & Blue
Sound-Active
Sou
Sensitivity
The product responds to the beat of the music
Sou
S 0~S 9
Sound (Random)
So1
S 0~S 9
Sound (Blue)
So2
S 0~S 9
Sound (Green)
So3
S 0~S 9
Sound (Green & Blue)
rAn
N/A
Random patterns & colors
Sensitivity
S 0~S 9
S 0~S 9
0 = least sensitive, 9 = most sensitive
DMX
000~502
DMX mode, sets starting address
SLA
Master/slave mode
rEn
Remote control mode

Rev. 2 14 Scorpion™ Burst GB User Manual
Configuration
(DMX)
Set the product in DMX mode to control with a DMX controller.
1. Connect the product to a suitable power outlet.
2. Turn the product on.
3. Connect a DMX cable from the DMX output of the DMX controller to the DMX input
socket on the product.
Starting Address
The Scorpion™ Burst GB uses up to 11 DMX channels in its DMX mode, which defines
the highest configurable address to 501
. If you are unfamiliar DMX, download the DMX
Primer from www.chauvetlighting.com.
To select the starting address, do the following:
1. Press <MENU>until a three-number value appears.
2. Select the value of your starting address, then press <ENTER>.
Configuration
(Standalone)
Set the product in one of the standalone modes to control without a DMX controller.
1. Connect the product to a suitable power outlet.
2. Turn the product on.
Never connect a product that is operating in any standalone mode (either
Static, Automatic, or Sound) to a DMX string connected to a DMX controller.
Products in standalone mode may transmit DMX signals that could
interfere with the DMX signals from the controller.
Sound-Active Mode
To enable the Sound-Active mode, do the following:
1. Press <MENU>repeatedly until Souor Aut shows on the display.
2. Press <UP> or <DOWN> until Sou shows on the display.
3. Press <ENTER>.
4. Turn the music on and press <MENU>until S 0(~9) shows on the display.
5. Use <UP> or <DOWN> to set the sound sensitivity from level S 1~S 9, with 9being
the most sensitive.
6. Press <ENTER>.
The product will only respond to low frequencies of music (bass and
drums).
Automatic Mode
To enable the Automatic mode, follow the instructions below:
1. Press <MENU> repeatedly until Sou or Aut shows on the display.
2. Press <MENU>repeatedly until Aut shows on the display.
3. Press <ENTER>.
4. Use <UP> or <DOWN> to select the desired effect for an automatic program.
5. Press <ENTER>.
Master/Slave Mode
The Master/Slave mode allows a single Scorpion™ Burst GB (the “master”) to control the
actions of one or more Scorpion™ Burst GB
units (the “slaves”) without the need of a
DMX controller. The master unit will be set to operate in either Automatic or Sound Active
mode, while the slave units will be set to operate in Slave Mode. Once set and
connected, the slave units will operate in unison with the master unit.
Configure the units as indicated below.
Slave units:
1. Press <MENU>repeatedly until SLA shows on the display.
2. Press <ENTER>.
3. Connect the DMX input of the first slave unit to the DMX output of the master unit.
4. Connect the DMX input of the subsequent slave units to the DMX output of the
previous slave unit.
5. Finish setting and connecting all the slave units.
Master unit:
1. Set the master unit to operate in either Automatic or Sound mode.
2. Make the master unit the first unit in the DMX daisy chain.
•Configure all the slave units before connecting the master unit to the DMX daisy
chain.
•Never connect a DMX controller to a DMX string configured for Master/Slave
operation because the controller may interfere with the signals from the master unit.
•
Do not connect more than 31 slave units to the master unit.

Scorpion™ Burst GB User Manual 15 Rev. 2
Remote Control
Button(s) Function Description
ON/OFF
Holding for 3 seconds will activate or deactivate
remote mode, so that the laser can be powered on or
off with the remote
AUTO MODE Laser runs on built-in automated programs
SOUND-ACTIVE
MODE
The blue music LED indicator is flashing when sound
signal is detected
SOUND
SENSITIVITY
In Sound-Active Mode, press MUSIC + B + “1~9” to
adjust sensitivity setting, “9” is the most sensitive
COLOR
CHANGING
Selects laser color: Green>Blue> G&B>
PATTERN
CHANGING
Press A and then a number (0~9)
BURST EFFECT
ROTATION
For Burst effect, press C + “1~9” to adjust field
rotation speed, “9” is the fastest
PATTERN SWAP
Pattern swap effect, switches between the last two
patterns selected
Turn the Laser
On/Off
Pattern Repeating
Sound Sensitivity
Effect Pause
Color Changing
Auto Mode
Sound-Active Mode
Fixed Pattern
(From 1 to 48)
Burst Effect Rotation
Pattern Changing

Rev. 2 16 Scorpion™ Burst GB User Manual
DMX Values
Channel
Value
Function
1
Control Mode
000 024
025 049
050 074
075 099
100 124
125 149
150 174
175 199
200 224
225 255
DMX Mode
Automatic mixed
Automatic 1
Automatic 2
Automatic 3
Sound mixed
Sound 1
Sound 2
Sound 3
Random
2
Patterns
000 010
011 020
021 030
031 040
041 050
051 060
061 070
071 080
081 090
091 100
101 110
111 120
121 130
131 140
141 150
151 160
161 170
171 180
181 190
191 200
201 210
211 220
221 230
231 255
Pattern 1
Pattern 2
Pattern 3
Pattern 4
Pattern 5
Pattern 6
Pattern 7
Pattern 8
Pattern 9
Pattern 10
Pattern 11
Pattern 12
Pattern 13
Pattern 14
Pattern 15
Pattern 16
Pattern 17
Pattern 18
Pattern 19
Pattern 20
Pattern 21
Pattern 22
Pattern 23
Pattern 24
3
Color Selection
000

004
005 028
029 056
057 084
085 112
113 140
141 168
169 197
198 224
225 255
Blackout
Blue
Green
Blue & Green
Green Strobing
Blue Strobing
Blue on Green Strobing
Green on & Blue Strobing
Blue & Green Strobing
Blue & Green (Alternating Strobe)
4
Color Changing Speed 000 004 005 255 No function Color Changing Speed (slow fast)
5
Zoom
000 027
028 169
170 209
210

255
100%5%
Zoom in
Zoom out
Zoom in and out
6
X-Axis Roll
000 127
128 191
192 255
X-Axis Roll
Roll (slow fast)
Roll (fast slow)
7
Y-Axis Roll
000 127
128 191
192

255
Y-Axis Roll
Roll (slow fast)
Roll (fast

slow)
8
Rotate (Z-Axis Roll)
000

127
128 191
192 255
Z-Axis Roll
Clockwise Rotate
Counterclockwise Rotate
Note: See next page for pattern list.

Scorpion™ Burst GB User Manual 17 Rev. 2
DMX Values (continued)
DMX Values and Pattern List
Channel
Value
Function
9
Pan (X-Axis)
000 127
128 191
192 255
128 fixed positions on the X-Axis
Clockwise pan
Counterclockwise pan
10
Tilt (Y-Axis)
000

127
128 191
192 255
128 fixed positions on the Y-Axis
Up to Down Tilt (slow to fast)
Up to Down Tilt (fast to slow)
11
Pattern Rotation
000
001 075
076 150
151

255
No function
Clockwise pattern rotation
No pattern rotation (laser is on, but not rotating)
Counterclockwise rotation
DMX
Pattern
DMX
Pattern
DMX
Pattern
DMX
Pattern
000~010
061~070
121~130
181~190
011~020
071~080
131~140
191~200
021~030
081~090
141~150
201~210
031~040
091~100
151~160
211~220
041~050
101~110
161~170
220~230
051~060
111~120
171~180
230~255

Rev. 2 18 Scorpion™ Burst GB User Manual
5.Technical Information
Product
Maintenance
Dust build-up reduces light output performance and can cause overheating. This can
lead to reduction of the light source’s life and mechanical wear. To maintain optimum
performance and minimize wear, clean your lighting products at least twice a month.
(Use and environmental conditions may require increased cleaning frequency.)
•Unplug the product from power.
•Wait until the product is cold.
•Use a vacuum (or dry compressed air) and a soft brush to remove dust collected on
the external surface and fan vents.
•Clean the glass panel (laser aperture) with a mild solution of glass cleaner or
isopropyl alcohol.
•Apply the solution directly to a soft, lint-free cotton cloth or a lens cleaning tissue,
and drag any dirt or grime to the outside of the glass.
•Gently polish the glass surface until it is free of haze and lint.
Always dry the glass surface carefully after cleaning them.
DO NOT spin the fan using compressed air because you could damage it.
DO NOT open this product for cleaning or servicing.

Scorpion™ Burst GB User Manual 19 Rev. 2
6.Technical Specifications
Dimensions and
Weight
Length
Width
Height
Weight
8 in (205 mm)
9.4 in (240 mm)
7.6 in (194 mm)
5.2 lbs (2.4 kg)
Note: Dimensions in inches rounded to the nearest decimal digit
Power
Power Supply Type
Range
Voltage Selection
Switching (internal)
100~240 V, 50/60 Hz
Auto-ranging
Parameter
120 V, 60 Hz
230 V, 50 Hz
Energy consumption
37 W
42 W
Operating current (units)
0.3 A
0.2 A
Power linking (units)
25 units
43 units
Fuse
T 1 A, 250 V
T 1 A, 250 V
Power I/O
U.S.
UK/Europe
Power input connector
IEC
IEC
Power output connector
Edison
N/A
Power cord plug
Edison
N/A
Light Source
Type
Power
Wavelength
Laser (green)
40 mW
532 nm
Laser (blue)
120 mW
450 nm
Photo Optic
Parameter
Value
Coverage angle
99º
Pan positioning
43º
Tilt positioning
39º
Thermal
Maximum External Temp.
Cooling System
104° F (40° C)
Fan cooled
DMX
I/O Connectors
Connector Type
Channel Range
3-pin XLR
Sockets
11
Ordering
Product Name
Item Code
UPC Number
Scorpion™ Burst GB
10060604
781462209520

Rev. 2 20 Scorpion™ Burst GB User Manual
To get support or return a product:
In the U.S., contact CHAUVET® World Headquarters.
In the UK or Ireland, contact CHAUVET® Europe Ltd.
In any other country, DO NOT contact CHAUVET®. Instead, contact your local
distributor. See www.chauvetlighting.com for distributors outside the U.S., UK, or
Ireland.
If you are located outside the U.S.,
UK, or Ireland, contact your distributor
and follow their instructions on how to return CHAUVET® products to
them. Visit our website for contact details.
Returns
Call the corresponding CHAUVET® Technical Support office and request a Return
Merchandise
Authorization (RMA) number before shipping the product. Be prepared to
provide the model number, serial number, and a brief description of the cause for the
return.
Send the merchandise prepaid, in its original box, and with its original packing and
accessories. CHAUVET® will not issue call tags.
Clearly label the package with the RMA number. CHAUVET® will refuse any product
returned without an RMA number.
Writ
e the RMA number on a properly affixed label. DO NOT write the RMA
number directly on the box.
Before sending the product, clearly write the following information on a piece of paper
and place it inside the box:
•Your name
•Your address
•Your phone number
•The RMA number
•A brief description of the problem
Be sure to pack the product properly. Any shipping damage resulting from inadequate
packaging will be your responsibility. FedEx packing or double-
boxing are
recommended.
CHAUVET® reserves the right to use its own discretion to repair or replace
returned product(s).
Contact Us
CHAUVET®
World Headquarters
General Information
Address: 5200 NW 108th Avenue
Sunrise, FL 33351
Voice: 954-577-4455
Fax: [phone]
Toll free: 1-800-762-1084
CHAUVET® Europe Ltd.
United Kingdom & Ireland
General Information
Address: Unit 1C
Brookhill Road Industrial Estate
Pinxton, Nottingham, UK
NG16 6NT
Voice: [phone]
Fax: [phone]
Technical Support
Voice: 954-577-4455 (Press 4)
Fax: [phone]
Email: [e-mail]
Technical Support
Email: [e-mail]
World Wide Web
www.chauvetlighting.com
World Wide Web
www.chauvetlighting.co.uk