Chauvet Mega Moon User manual

User Manual
Snapshot
Use on Dimmer
Outdoor Use
Sound Activated
DMX 512
Master/Slave
Autoswitching
Power Supply
Replaceable Fuse
User Serviceable
Duty Cycle

Mega Moon™User Manual 2 9/16/2010 4:11 PM
CHAUVET®, 2010, All Rights Reserved
Information and specifications in this User Manual are subject to change without notice. CHAUVET® assumes no
responsibility or liability for any errors or inaccuracies that may appear in this manual.
Rev01b
TABLE OF CONTENTS
1. BEFORE YOU BEGIN................................................................................................................................................... 3
WHAT IS INCLUDED ................................................................................................................................................................................ 3
UNPACKING INSTRUCTIONS .................................................................................................................................................................... 3
SYMBOLS ............................................................................................................................................................................................. 3
AC POWER........................................................................................................................................................................................... 3
SAFETY INSTRUCTIONS .......................................................................................................................................................................... 4
2. INTRODUCTION ........................................................................................................................................................... 4
FEATURES ............................................................................................................................................................................................ 4
Additional Features................................................................................................................................................... 4
DMX CHANNEL SUMMARY ..................................................................................................................................................................... 5
PRODUCT OVERVIEW............................................................................................................................................................................. 5
3. SETUP .......................................................................................................................................................................... 6
FUSE REPLACEMENT ............................................................................................................................................................................. 6
FIXTURE LINKING................................................................................................................................................................................... 6
DMX Data Cable....................................................................................................................................................... 6
Cable Connectors..................................................................................................................................................... 7
3-Pin to 5-Pin Conversion Chart................................................................................................................................ 7
Setting up a DMX Serial Data Link............................................................................................................................ 7
MASTER/SLAVE FIXTURE LINKING........................................................................................................................................................... 8
MOUNTING............................................................................................................................................................................................ 8
Orientation................................................................................................................................................................ 8
Rigging ..................................................................................................................................................................... 8
4. OPERATING INSTRUCTIONS...................................................................................................................................... 9
OPERATION MODES............................................................................................................................................................................... 9
Stand-Alone Mode (Sound-Active, Auto Mode)......................................................................................................... 9
Master/Slave Mode (Master Sound, Master Auto)..................................................................................................... 9
DMX Mode.............................................................................................................................................................. 10
USING DMX MODE ............................................................................................................................................................................. 10
DMX Channel Values.............................................................................................................................................. 10
Setting the Starting Address.................................................................................................................................... 11
GENERAL TROUBLESHOOTING .............................................................................................................................................................. 11
CONTACT US...................................................................................................................................................................................... 12
5. APPENDIX.................................................................................................................................................................. 12
DMX PRIMER ..................................................................................................................................................................................... 12
GENERAL MAINTENANCE...................................................................................................................................................................... 13
RETURNS PROCEDURE ........................................................................................................................................................................ 13
CLAIMS .............................................................................................................................................................................................. 13
TECHNICAL SPECIFICATIONS ................................................................................................................................................................ 14

Mega Moon™User Manual 3 9/16/2010 4:11 PM
1. BEFORE YOU BEGIN
What is included
1 x Mega Moon™
1 x Power Cord
1 x Warranty Card
1 x User Manual
Unpacking Instructions
Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that
all parts are present, and have arrived in good condition. Notify the shipper immediately and retain
the packing material for inspection if any parts appear damaged from shipping or the carton shows
signs of mishandling. Save the carton and all packing materials. In the event that a fixture must be
returned to the factory, it is important that the fixture be returned in the original factory box and
packing.
Symbols
This paragraph contains critical installation, configuration or operation information. Failure to comply
with this information may render the fixture partially or completely inoperative, cause damage to the
fixture or cause harm to the operator/user/technician.
This paragraph contains important installation or configuration information. Failure to comply with this
information may prevent the fixture from functioning correctly.
This paragraph reminds you of useful, although not critical, information.
AC Power
This fixture has an auto-switching power supply that can accommodate a wide range of input voltages
(100V - 240VAC, 50/60Hz). Before powering on the unit, make sure the line voltage to which you are
connecting it is within the range of accepted voltages.
Always connect the fixture to a switched circuit. Never connect the fixture to a
rheostat (variable resistor) or dimmer circuit, even if the rheostat or dimmer
channel is used only as a 0% to 100% switch.
To determine the power requirements for a particular fixture, see the label affixed to the back plate of
the fixture or refer to the fixture’s specifications chart. A fixture’s listed current rating indicates its
average current draw under normal conditions.
Before applying power to a fixture, check that the source voltage matches the fixture’s requirement.
Check the fixture or device carefully to make sure that if a voltage selection switch exists, it is set to
the correct line voltage you will use.
Always connect the fixture to a circuit with a suitable electrical ground.

Mega Moon™User Manual 4 9/16/2010 4:11 PM
Safety Instructions
Please read these instructions carefully, which include important information about
the installation, usage and maintenance of this product.
Please keep this User Guide for future consultation. If you sell the unit to another user, be sure
that they also receive this instruction booklet.
This product is for indoor use only! To prevent risk of fire or shock, do not expose fixture to rain
or moisture.
Make sure there are no flammable materials close to the unit while operating.
Secure fixture to fastening device using a safety chain.
Maximum ambient temperature (Ta) is 104°F (40°C). Do not operate the fixture at temperatures
higher than this.
In the event of a serious operating problem, stop using the unit immediately. Never try to repair
the fixture by yourself. Repairs carried out by unskilled people can lead to damage or
malfunction. Please contact the nearest authorized technical assistance center.
Make sure the power cord is not crimped or damaged.
Never disconnect the power cord by pulling or tugging on the cord.
Avoid direct eye exposure to the light source while it is on.
Do not daisy chain power to more than 37 units @ 120V.
There are no user serviceable parts inside the unit. Do not open the housing or
attempt any repairs. In the unlikely event that your unit may require service, please
contact CHAUVET at 954-929-1115.
2. INTRODUCTION
Features
6-channel DMX-512 LED beam effect
Individual control of red, green, blue and white LEDs within each cluster (4 total)
Adjustable strobe speed
Built-in automated programs via DMX
Built-in sound activated programs via master/slave or DMX
Additional Features
Razor-sharp rotating beams
Additional power output: max 37 units @ 120V

Mega Moon™User Manual 5 9/16/2010 4:11 PM
DMX Channel Summary
CHANNEL
FUNCTION
1
Module 1
2
Module 2
3
Module 3
4
Module 4
5
Strobe
6
Function
Product Overview
DIP
switches
Fuse holder
Power in
Bracket
adjustment
knob (1 of 2)
DMX in
Safety
eyebolt
DMX out
Hanging
bracket
Power out
Microphone
sensitivity
Microphone

Mega Moon™User Manual 6 9/16/2010 4:11 PM
The fuse is located
inside this
compartment.
Remove using a flat
head screwdriver.
3. SETUP
Fuse Replacement
Disconnect the power cord before replacing a fuse and always replace with the
same type of fuse.
With a flat head screwdriver, wedge the fuse
holder out of its housing. Remove the blown
fuse from its holder and replace with the exact
same type of fuse. Insert the fuse holder back
in its place and reconnect power.
Fixture Linking
You will need a serial data link to run light shows of one or more fixtures using a DMX-512 controller
or to run synchronized shows on two or more fixtures set to a master/slave operating mode. The
combined number of channels required by all the fixtures on a serial data link determines the number
of fixtures the data link can support.
Fixtures on a serial data link must be daisy chained in one single line. To comply
with the EIA-485 standard no more than 32 devices should be connected on one
data link. Connecting more than 32 fixtures on one serial data link without the use
of an optically isolated DMX splitter may result in deterioration of the digital DMX
signal.
Maximum recommended serial data link distance: 500 m (1640 ft.)
Maximum recommended number of fixtures on a serial data link: 32
DMX Data Cable
To link two or more fixtures together you must use DMX compliant data cables. You can purchase
CHAUVET certified DMX cables directly from a dealer/distributor or construct your own cable.
If you choose to create your own cable, please use data-grade cables that can carry a high quality
signal and are less prone to electromagnetic interference. Use a Belden© 9841 or equivalent cable,
which meets the specifications for EIA RS-485 applications.
Standard microphone cables cannot transmit DMX data reliably over long
distances.
The cable must have the following characteristics:
Type: shielded, 2-conductor twisted pair
Maximum capacitance between conductors: 30 pF/ft.
Maximum capacitance between conductor and shield: 55 pF/ft.
Maximum resistance: 20 ohms / 1000 ft.
Nominal impedance: 100 –140 ohms

Mega Moon™User Manual 7 9/16/2010 4:11 PM
This drawing provides
a general illustration of
the DMX Input/Output
panel of a lighting
fixture.
Universal DMX Controller
Continue the link
Cable Connectors
Cabling must have a male XLR connector on one end and a female XLR connector on the other end.
Do not allow contact between the common and the fixture’s chassis ground.
Grounding the common can cause a ground loop, and your fixture may perform
erratically. Test the cables with an ohmmeter to verify correct polarity and to make
sure the pins are not grounded or shorted to each other.
3-Pin to 5-Pin Conversion Chart
If you use a controller with a 5-pin DMX output connector, you will need to use a 5-
pin to 3-pin adapter. You may use the CHAUVET Model number DMX5M, or DMX5F.
The chart below details the proper cable conversion:
3-PIN TO 5-PIN CONVERSION CHART
Conductor
3-Pin Female (output)
5-Pin Male (Input)
Ground/Shield
Pin 1
Pin 1
Data ( - ) signal
Pin 2
Pin 2
Data ( + ) signal
Pin 3
Pin 3
Do not use
Pin 4
Do not use
Pin 5
Setting up a DMX Serial Data Link
1. Connect the (male) 3-pin connector of the
DMX cable to the output (female) 3-pin
connector of the controller.
2. Connect the other end of the cable to the
(male) 3-pin input connector of the first
fixture
3. Connect the cable from the output of the
first fixture to the input of the second
fixture.
4. Continue connecting the other features as
indicated above.
CHAUVET Certified DMX Data Cables
Order Code Description
DMX1.5 DMX Cable 1.5 m/4.9 ft
DMX4.5 DMX Cable 4.5 m/14.8 ft
DMX10 DMX Cable 10 m/32.8 ft
COMMON
DMX +
DMX -
INPUT
OUTPUT
1
3
2
1
3
2
1
3
2
120 ohm, ¼ W
resistor between
pin 2 (DMX -) and
pin 3 (DMX +) of
the last fixture.
To avoid signal transmission
problems and interference, it is
always advisable to connect a DMX
signal terminator.
DMX connector configuration

Mega Moon™User Manual 8 9/16/2010 4:11 PM
Master
Slave
Slave
Hanging Clamp
Master/Slave Fixture Linking
1. Link the fixtures as indicated in steps 1 to 4 of the previous section.
2. The setup of the Master/Slave or Stand-alone operation often requires the first fixture in the chain
to be initialized accordingly via settings in the control.
3. In addition, in the Master/Slave mode, the fixtures that follow may also need to be initialized as
“slaves.” Please consult the Operating Instructions section in this manual for complete
instructions for this type of configuration.
Mounting
Orientation
This fixture may be mounted in any safe position.
Rigging
It is important never to obstruct the vents pathway. Mount the fixture using, a suitable “C” or “O” type
clamp. Adjust the angle of the fixture by loosening both knobs and tilting the fixture. After finding the
desired position, retighten both knobs.
When selecting an installation location, consider ease of access to the fixture for operation and
routine maintenance.
Always use safety cables.
Never mount the fixture in places where it may be exposed to rain, high humidity, extreme
temperature changes or restricted ventilation.
The clamp is sold separately

Mega Moon™User Manual 9 9/16/2010 4:11 PM
4. OPERATING INSTRUCTIONS
Operation Modes
The fixture may be operated on stand-alone (sound activated), Master/Slave Mode or DMX Mode.
Stand-Alone Mode (Sound-Active)
This mode allows a single fixture to run to the beat of the music, or the fixture will change
automatically in Auto Mode.
1) Set the DIP switches position to Sound Active or Auto Mode.
Mode DIP switches
Master sound-active 1~10 = Off
2) The fixture will react to the low frequencies of music via the internal microphone in Sound Active
mode.
3) Use the audio sensitivity knob on the back of the fixture to make the fixture more or less
sensitive in Sound-Active mode. Turning the knob counterclockwise decreases the sensitivity;
turning the knob clockwise increases the sensitivity.
Note: To use the fixture in automatic (without the sound trigger), you must use a DMX controller.
Master/Slave Mode (Sound)
This mode will allow you to link up to 32 fixtures together without a controller.
1) Use standard DMX cables to daisy chain your fixtures together via the DMX connector on the
rear of the fixtures. (For longer cable runs, we suggest a terminator at the output of the last
fixture).
2) Choose a fixture to function as the Master. Turn DIP switches to the Master position on the
fixture. The Master fixture must be the first fixture in line.
3) Please see the DIP switches settings for Stand-Alone Mode (described above) to set the fixture
to the Master setting of your choice.
4) Turn the DIP switches to the Slave position on the Slave fixture, and they will react the same as
the Master.
Mode DIP switches
Slave 1, 10 = On

Mega Moon™User Manual 10 9/16/2010 4:11 PM
DMX Mode
This mode allows the fixture to receive control from any universal DMX controller.
Using DMX Mode
If you are unfamiliar with DMX, please read the DMX Primer section.
1) Using DMX cables, daisy chain the fixture(s), starting from the output of the DMX controller.
2) Assign the individual DMX address, using DIP switches 1 - 9 on each fixture.
3) Set the fixture to DMX operation mode by turning DIP switch 10 to the on position.
DMX Channel Values
CHANNEL
VALUE
FUNCTION
1-4
000 010
011 016
017 022
023 028
029 034
035 040
041 046
047 052
053 058
059 064
065 070
071 076
077 082
083 088
089 094
095 100
101 106
107 112
113 118
119 124
125 130
131 136
137 142
143 148
149 154
155 160
161 166
167 172
173 178
179 184
185 190
191 196
197 202
203 208
209 214
215 220
221 255
Module 1-4
No function
Group 1 of White
Group 2 of White
Group 3 of White
Group 1 of Red
Group 2 of Red
Group 3 of Red
Group 1 of Green
Group 2 of Green
Group 3 of Green
Group 1 of Blue
Group 2 of Blue
Group 3 of Blue
All White
All Red
All Green
All Blue
All Red & Green
All Red & Blue
All Green & Blue
All Red & Green & Blue
All Red & White
All Green & White
All Blue & White
Group 1 of Blue & all White
Group 2 of Blue & all Red
Group 3 of Blue & all Green
Group 1 of Blue & group 3 of Red
Group 2 of Blue & group 2 of Red
Group 3 of Blue & group 1 of Red
Group 1 of Green & group 3 of White
Group 2 of Green & group 2 of White
Group 3 of Green & group 1 of White
Group 1 of Blue, group 3 of Green, group 1 of Red, & group 3 of White
Group 2 of Blue, group 2 of Green, group 2 of Red, & group 2 of White
Group 3 of Blue, group 1 of Green, group 3 of Red, & group 1 of White
All White & Red & Green & Blue
5
000 010
011 255
Strobe
No function
Strobe: (Slow > Fast)
6
000 010
011 036
037 062
063 088
089 114
115 130
131 156
157 182
183 208
209 250
251 255
Function
No function
Program 1
Program 2
Program 3
Program 4
Program 5
Program 6
Program 7
Program 8
Auto mode
Sound mode

Mega Moon™User Manual 11 9/16/2010 4:11 PM
Setting the Starting Address
If this is your first time addressing a fixture using the DMX-512 control protocol, we
suggest you to go to the Appendix Section and read the DMX Primer section. It
contains very useful information that will help you understand how DMX works.
General Troubleshooting
Symptom
Solution(s)
Applies to
Lights
Foggers &
Snow
Controllers
Dimmers &
Chaser
Auto shut off
Check fan thermal switch reset

Beam is very dim or not
bright
Clean optical system or replace lamp
Check 220/110 V switch for proper setting

Breaker/Fuse keeps
blowing
Check total load placed on device

Chase is too slow
Check user’s manual for speed adjustment



Device has no power
Check for power on Mains.
Check device’s fuse. (internal and/or external)



Fixture is not
responding
Check DMX Dip switch settings for correct
addressing
Check DMX cables
Check polarity switch settings

Fixture is on but there
is no movement to the
audio
Make sure you have the correct audio mode on
the control switches. If audio provided via ¼” jack,
make sure a live audio signal exists
Adjust sound sensitivity knob



Light will not come on
after power failure
Some discharge lamps require a cooling off period
before the electronics in the fixture can kick start it
again. Wait 5 to 10 minutes before powering it up
again.

Loss of signal
Use only DMX cables
Install terminator
Note: Keep DMX cables separated from power
cables or black lights.




No flash
Re-install bulb; it may have shifted in shipping

No light output
Check slip ring & brushes for contact
Install bulb
Call service technician

Relay will not work
Check reset switch
Check cable connections

Remote does not work
Make sure connector is firmly attached to device


If you still have a problem after trying the above solutions, please contact CHAUVET®
Technical Support at the location on the next page.

Mega Moon™User Manual 12 9/16/2010 4:11 PM
Contact Us
World Wide
General Information CHAUVET®
5200 NW 108th Ave
Sunrise, FL 33351
voice: 954.929.1115
fax: [phone]
toll free: 800.762.1084
Technical Support CHAUVET®
5200 NW 108th Ave
Sunrise, FL 33351
voice: 954.929.1115 (Press 4)
fax: [phone] (Attention: Service)
World Wide Web www.chauvetlighting.com
5. APPENDIX
DMX Primer
The DMX mode enables the use of a universal DMX controller device. There are 512 channels in a
DMX-512 connection. Channels may be assigned in any manner. A fixture capable of receiving DMX
512 will require access to one or more sequential channels. To do this, each fixture requires a "start
address" from 1 to 512. A fixture requiring one or more channels for control begins to read the data
on the channel indicated by the start address. For example, a fixture that uses six DMX channels and
was addressed to start on DMX channel 100, would read data from channels: 100, 101, 102, 103,
104, and 105.
The user must assign a starting address on the fixture that indicates the first channel reserved in the
controller. There are many different types of DMX controllable fixtures and they all may vary in the
total number of channels required. Choosing a start address should be planned in advance. Channels
should never overlap. If they do, this will result in erratic operation of the fixtures whose starting
address are set incorrectly. However, you can control multiple fixtures of the same type using the
same starting address as long as the intended result is that of unison movement or operation. In other
words, the fixtures will be slaved together and they will all respond in exactly the same way.
DMX fixtures are designed to receive data through a serial DMX Daisy Chain. In a Daisy Chain, the
DATA OUT of one fixture connects to the DATA IN of the next fixture. The order in which the fixtures
are connected is not important and has no effect on how a controller communicates to each fixture.
Use an order that provides for the easiest and most direct cabling, however.
Connect the fixtures using a shielded, two-conductor twisted pair cable with one 3-pin XLR male
connector on one end and a 3-pin XLR female connector on the other end. The shield connection is
pin 1, while pin 2 is Data Negative (S-) and pin 3 is Data positive (S+). See page 6 for details on this
type of cable.

Mega Moon™User Manual 13 9/16/2010 4:11 PM
General Maintenance
To maintain optimum performance and minimize wear, fixtures should be cleaned frequently. Usage
and environment are contributing factors in determining the cleaning frequency. As a general rule,
fixtures should be cleaned at least twice a month. Dust build up reduces light output performance and
can cause overheating. This can lead to reduced lamp life and increased mechanical wear. Be sure
to power off fixture before conducting maintenance.
Unplug fixture from power. Use a vacuum or air compressor and a soft brush to remove dust
collected on external vents and internal components. Clean all glass surfaces when the fixture is cold
with a mild solution of glass cleaner or Isopropyl Alcohol and a soft lint-free cotton cloth or lens tissue.
Apply solution to the cloth or tissue and drag dirt and grime to the outside of the lens. Gently polish
optical surfaces until they are free of haze and lint.
The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to
optimize light output. Cleaning frequency depends on the environment in which the fixture operates:
damp, smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit’s
optics. Clean with soft cloth using normal glass cleaning fluid. Always dry the parts carefully. Clean
the external optics at least every 20 days. Clean the internal optics at least every 30/60 days.
Returns Procedure
Returned merchandise must be sent prepaid and in the original packing; call tags will not be issued.
Package must be clearly labeled with a Return Merchandise Authorization Number (RMA #).
Products returned without an RMA # will be refused. Call CHAUVET and request an RMA #, prior to
shipping the fixture. Be prepared to provide the model number, serial number and a brief description
of the cause for the return. Be sure to properly pack fixture; any shipping damage resulting from
inadequate packaging is the customer’s responsibility. As a suggestion, proper UPS packing or
double-boxing is always a safe method to use. CHAUVET reserves the right to use its own discretion
to repair or replace product(s).
Once you have received the RMA#, please include the following information on a
piece of paper inside the box:
1) Your name
2) Your address
3) Your phone number
4) The RMA #
5) A brief description of the symptoms
Claims
Damage incurred in shipping is the responsibility of the shipper; therefore, any damage must be
reported to the carrier upon receipt of merchandise. It is the customer's responsibility to notify and
submit claims with the shipper in the event that a fixture is damaged during shipping. Any other claim
for items such as missing component/part, damage not related to shipping, and concealed damage
must be made within seven (7) days of receiving merchandise.

Mega Moon™User Manual 14 9/16/2010 4:11 PM
Technical Specifications
WEIGHT & DIMENSIONS
Length........................................................................................................................18.3 in (465 mm)
Width..........................................................................................................................12.2 in (310 mm)
Height ..........................................................................................................................6.7 in (170 mm)
Weight.............................................................................................................................. 8.9 lbs (4 kg)
POWER
Autoswitching................................................................................................... 100-240 VAC 50/60 Hz
Fuse................................................................................................. F2 A 250 V (5 x 20 mm fast-blow)
Power Consumption....................................................................................18 W (0.2 A) max @ 120 V
Inrush Current............................................................................................................. (0.2 A) @ 120 V
Power Consumption....................................................................................17 W (0.1 A) max @ 230 V
Inrush Current............................................................................................................. (0.1 A) @ 230 V
Power Output............................................................37 units max @ 120 VAC, 74 units max @ 230 V
LIGHT SOURCE
LED................................................................ 228 (48 Red, 72 Green, 72 Blue, 36 White) 100,000 hrs
COVERAGE
Coverage angle (horizontal spread) ................................................................................................74°
THERMAL
Maximum ambient temperature......................................................................................104° F (40° C)
CONTROL & PROGRAMMING
Data input ............................................................................................. locking 3-pin XLR male socket
Data output ........................................................................................ locking 3-pin XLR female socket
Data pin configuration ............................................................................pin 1 shield, pin 2 (-), pin 3 (+)
Protocols.....................................................................................................................DMX-512 USITT
DMX Channels....................................................................................................................................6
ORDERING INFORMATION
Mega Moon™................................................................................................................. MEGAMOON
WARRANTY INFORMATION
Warranty...........................................................................................................2-year limited warranty