Chauvet Freedom Par Tri-6 User manual

User Manual

Freedom™ Par Tri-6 User Manual Rev. 1
TABLE OF CONTENTS
1. Before You Begin............................................................................................................................. 3
What Is Included.......................................................................................................................................................................3
Unpacking Instructions .............................................................................................................................................................3
Claims...................................................................................................................................................................................3
Text Conventions......................................................................................................................................................................3
Symbols....................................................................................................................................................................................3
Disclaimer.................................................................................................................................................................................3
Product at a Glance..................................................................................................................................................................4
2. Introduction...................................................................................................................................... 5
Overview...................................................................................................................................................................................5
Description................................................................................................................................................................................5
Dimensions...............................................................................................................................................................................6
3. Setup ................................................................................................................................................ 7
AC Power .................................................................................................................................................................................7
Fuse Replacement....................................................................................................................................................................7
Fuse Replacement Diagram .................................................................................................................................................7
Power Linking...........................................................................................................................................................................8
Battery Run Time......................................................................................................................................................................8
Mounting...................................................................................................................................................................................9
Orientation................................................................................................................................................................................9
Rigging .....................................................................................................................................................................................9
4. Operation........................................................................................................................................ 10
Control Panel Operation.........................................................................................................................................................10
Menu Map...........................................................................................................................................................................10
DMX Linking...........................................................................................................................................................................11
Starting Address..................................................................................................................................................................11
Master/Slave Mode.............................................................................................................................................................11
DMX Personalities...............................................................................................................................................................11
D-Fi™ 2.4 GHz (DMX Mode Manual Sync)............................................................................................................................12
D-Fi™ 2.4 GHz (DMX Mode Auto Sync)................................................................................................................................13
DMX Channel Assignments and Values .............................................................................................................................14
Configuration (Standalone).....................................................................................................................................................17
Sound-Active Mode.............................................................................................................................................................17
Sound Sensitivity.................................................................................................................................................................17
Auto Programs....................................................................................................................................................................17
Program Speed...................................................................................................................................................................17
Selecting the Dimmer Speed Mode....................................................................................................................................17
Static Colors........................................................................................................................................................................17
Custom Color Mixing...........................................................................................................................................................17
Infrared Mode......................................................................................................................................................................18
IRC-6 Operations.............................................................................................................................................................18
5. Technical Information.................................................................................................................... 19
Product Maintenance..............................................................................................................................................................19
6. Technical Specifications............................................................................................................... 20
Returns............................................................................................................................................... 21
Contact Us.......................................................................................................................................... 22

Freedom™ Par Tri-6 User Manual Rev. 1 Page 3 of 22
1.
B
EFORE
Y
OU
B
EGIN
What Is
Included
•Freedom™ Par Tri-6
•Power Cord
•IRC-6 (Infrared Remote Control)
•Warranty Card
•Quick Reference Guide
Unpacking
Instructions
Carefully unpack the Freedom™ Par Tri-6
and check that all the parts are in the package, and are in good
condition.
Claims
If the box, or any of the contents, appear damaged from shipping, save all the packaging and file a claim
with the carrier immediately. Failure to report damage to the carrier immediately, or failure to save all the
packaging, can invalidate a claim.
For other issues, such as missing components or parts, damage not related to shipping, or concealed
damage, file a claim with Chauvet within 7 days of delivery. See Contact Us.
Text
Conventions
Convention
Meaning
1—512
A range of values
50/60
A set of values of which only one can be chosen
Settings
A menu option not to be modified
Menu > Settings
A sequence of menu options to be followed
<Enter>
A key to be pressed on the product’s control panel
ON
A value to be entered or selected
Symbols
Symbol
Meaning
Critical installation, configuration, or operation information. Not following these
instructions may make the product not work, cause damage to the product
, or
cause harm to the operator.
Important installation or configuration information. The product may not function
correctly if this information is not used.
Useful information.
Disclaimer
The information and specifications contained in this User Manual are subject to change without notice.
Chauvet
assumes no responsibility or liability for any errors or omissions, and reserves the right to revise
or recreate this manual at any time. The latest version of this manual can
be downloaded from
http://www.chauvetlighting.com/product-manuals-literature/.
© Copyright 2014 Chauvet. All rights reserved.
Electronically published by Chauvet in the United States of America.
Author Date Editor Date
A. Leon
11/19/2014
M. Trouard
12/16/14

Page 4 of 22 Freedom™ Par Tri-6 User Manual Rev. 1
Product at a
Glance
Use on Dimmer
x
Auto Program
P
Outdoor Use
x
Auto-Ranging Power Supply
P
Sound-Activated
P
Replaceable Fuse
P
DMX
P
User-Serviceable
x
Master/Slave
P
Safety Notes
These notes include important information about the mounting, usage, and maintenance
of this product;
read before using the product.
•Always connect the product to a grounded circuit to avoid the risk of electrocution.
•Always disconnect the product from the power source before cleaning or replacing the fuse.
•Avoid direct eye exposure to the light source while the product is on.
•Make sure the power cord is not crimped or damaged.
•Never disconnect the product from power by pulling or tugging on the cord.
•If mounting the product overhead, always secure to a fastening device using a safety cable.
•Make sure there are no flammable materials close to the product when operating.
•
Do not touch the product’s housing when operating because it may be very hot.
•Always make sure that the voltage of the outlet to which you are connecting the product is within the
range stated on the decal or rear panel of the product.
•The product is for indoor use only! (IP20) To prevent risk of fire or shock, do not expose the product
to rain or moisture.
•Always install the product in a location with adequate ventilation, at least
20 in (50 cm) from adjacent surfaces.
•Be sure that no ventilation slots on the product’s housing are blocked.
•Never connect the product to a dimmer.
•Make sure to replace the fuse with another of the same type and rating.
•Never carry the product from the power cord.
•The maximum ambient temperature (Ta) is 104 °F (40 °C). Do not operate the product at higher
temperatures.
•In the event of a serious operating problem, stop using the product immediately.
•Never try to repair the product. Repairs carried out by unskilled people can lead to damage or
malfunction. Contact the nearest authorized technical assistance center.
•This product is not intended for permanent installation.
•To eliminate unnecessary wear and improve its lifespan, during periods of non-use completely
disconnect the product from power via breaker or by unplugging it.
Keep
this User Manual for future use. If you sell the product to another user, be sure to give this document
to the next owner.

Freedom™ Par Tri-6 User Manual Rev. 1 Page 5 of 22
2. INTRODUCTION
Overview
Description
The Freedom™ Par Tri-6 is a wireless, battery-operated, tri-color LED Par with a built-in D-Fi™
transceiver. It works with the FlareCON™ Air and IRC-
6 for wireless triggering and control. You can
wirelessly master/slave this fixture with other Freedom™ fix
tures for a coordinated light show. Shine light
where it is needed using the built-in adjustable kickstand. Extend the battery’s lifespan with built-in
discharge protection. The Freedom™ Par Tri-6’s compact and lightweight design easily fits inside sticks of
TRUSST®.
Infrared Sensor
On/Off Switch
Display
DMX In DMX Out
Menu
Buttons
Power In
Power Out
Fuse Holder
Battery Life Indicator LEDs
Kickstand
Carry Handle
Glare Shield
Microphone
D-Fi™ AUTO
Sync/Clear Button

Page 6 of 22 Freedom™ Par Tri-6 User Manual Rev. 1
Dimensions
5.4 in
138 mm
5.7 in
145 mm
7.2 in
184 mm

Freedom™ Par Tri-6 User Manual Rev. 1 Page 7 of 22
3. SETUP
AC Power
The Freedom™ Par Tri-6 has an internal auto-ranging power supply and it can work with an input voltage
range of 100 to 240 VAC, 50/60 Hz.
Always connect
the product to a protected circuit (circuit breaker or fuse). Make sure the product
has an appropriate electrical ground to avoid the risk of electrocution or fire.
Never connect the product to a rheostat (variable resistor) or dimmer circuit, even if
the rheostat or
dimmer channel serves only as a 0 to 100% switch.
Fuse
Replacement
1. Disconnect the product from power.
2. Wedge the tip of a flat-head screwdriver into the slot of the fuse holder.
3. Pry the fuse holder out of the housing.
4. Remove the blown fuse from the holder.
5. Replace with a fuse of the exact same type and rating.
6. Insert the fuse holder back in place and reconnect power.
Disconnect the product from power before replacing the fuse.
Fuse
Replacement
Diagram
Always replace a blown fuse with another of the same type and rating.
A spare fuse is not included; however, the safety cap has room for a spare.
Spare Fuse
holder (inside
safety cap)
Installed Fuse
(held by plastic clip)
Safety
Cap

Page 8 of 22 Freedom™ Par Tri-6 User Manual Rev. 1
Power Linking
Daisy chaining products together through their Power In and Power Out sockets, called power linking,
allows many products to be powered from one power outlet.
Up to 17 Freedom™ Par Tri-6 products can be power linked at 120 V,
and up to
30 Freedom™ Par Tri-6 products can be power linked at 230 V.
Battery Power
The Freedom™ Par Tri-6 comes with a rechargeable lithium battery for cable-free operation.
Charging the
Battery
The battery charges whenever the product is plugged into a power source. If the product is plugged in and
not in operation, make sure the On/Off switch is in the Off position.
For optimal battery life, charge the Freedom™ Par Tri-6 battery for 24 hours prior to initial use.
Battery Life
Indicator
The battery life indicators are the 4 small green LEDs on either side of the
D-Fi™ <AUTO> button. The indicators show how much battery life remains available. The diagram
below
provides a key to reading the battery life indicators.
100%
75%
50%
25%
Battery Run
Time
Maximum Run Time
(all colors on)
Maximum Run Time
(single color on)
Recharge Time
Up to 8 hours
Up to 20 hours
6 hours
D-Fi™ AUTO Button

Freedom™ Par Tri-6 User Manual Rev. 1 Page 9 of 22
Mounting
Before mounting the product, read and follow the safety recommendations indicated in Safety Notes.
Orientation
The Freedom™ Par Tri-6 has a compact design to fit perfectly inside the TRUSST® truss systems. It
attaches to 35-50 mm truss without the need for a bracket, using an M12 threaded rigging point.
Floor
mounting is a cinch with a built-in adjustable kickstand. The product
may be mounted in any position;
however, place the product so there is at least 20
” of space around it and it is accessible for programming
and control panel operation.
Rigging
Rig the product from a structure or surface that can support the product’s weight. See Technical
Specifications in this manual for the product’s weight.
When mounting the product overhead, always use a mounting clamp and safety cable. Mount the product
securely to a rigging point, such as a pipe or truss. The CHAUVET® CH-05 safety cable is
appropriate for
this product.
When rigging the
product onto a truss, you should use a mounting clamp of appropriate weight capacity.
The Freedom™ Par Tri-6 has an M12 threaded mounting hole, which is appropriate for this purpose. For
the Chauvet line of mounting clamps, go to www.chauvetlighting.com/cables-clamps-main.html/.
When mounting the product on the floor, make sure that the product and any
cables are away from people
and vehicles.
Mounting
Diagram
Safety Cable
(such as CH-05 from
Chauvet)
Mounting Clamp
(such as the CLP-15 clamp
from Chauvet)
Threaded Mounting
Hole Size M12

Page 10 of 22 Freedom™ Par Tri-6 User Manual Rev. 1
4. OPERATION
Control Panel
Operation
To access the control panel functions, use the four buttons located underneath the display.
Button
Function
<MENU>
Selects an operation mode
<UP>
Scrolls up the list of options or selects a higher value
<DOWN>
Scrolls down the list of options or selects a lower value
<ENTER>
Activates a menu option or a selected value
<AUTO>
Auto-syncs D-Fi™ or displays information about D-Fi™ status
Menu Map
The Menu Map outlines the functions available through the menu, the programming levels that can be entered, and a
description for each function.
Main Function Programming Levels Description
DMX Personality and
Starting Address
3-CH
d 1–d512 Selects DMX personality and DMX starting value
4-CH
5-CH
9-CH
Static Colors
C--
C 1–C 7
Selects 1 of 7 static colors
Auto Programs
P--
P 1–P 4
Selects 1 of 4 auto programs
Program Speed
S--
S 1–S100
Sets auto program speed (slow to fast)
Sound-Active
Snd
Selects Sound-Active mode
Sound Sensitivity
SenS
u 0–u100
Sets sound sensitivity (low to high)
Custom Color Mixing U--
r 0–r255
Red (0–100%)
g0–g255
Green (0–100%)
b0–b255
Blue (0–100%)
Dimmer dIM
OFF
Sets the dimming speed mode: dIM1 (fast) to
dIM3 (slow), or OFF
dIM1
dIM2
dIM3
Infrared SET
On
Turns infrared on or off
OFF
2.4 GHz D-Fi™ S-tr
drAS
drAU
Automatically select receive frequency
drCH
dr 1–dr16
Manually select receive frequency
dtAS
dtAU
Automatically select transmit frequency
dtCH
dt 1–dt16
Manually select transmit frequency

Freedom™ Par Tri-6 User Manual Rev. 1 Page 11 of 22
DMX Linking
The Freedom™ Par Tri-6 operates in Master/Slave mode, or in DMX mode, both of which require DMX
linking. In Master/Slave mode the master product sends DMX signals to the slaves. In DMX mode the
lighting control board sends DMX signals to the products.
To DMX-link a number of Freedom™ Par Tri-6 using wireless D-Fi™, see D-Fi™ 2.4 GHz (DMX Mode
Manual Sync).
To DMX link a number of Freedom™ Par Tri-6 using DMX cable
•connect the DMX cable from DMX Out of the board, to DMX In of the first product, or
•connect the DMX cable from DMX Out of the master, to DMX In of the first slave.
Then connect another DMX cable from DMX Out of the first product/slave to DMX I
n of the next
product/slave.
Continue connecting each subsequent product until all the products are part of the chain.
Information about DMX is in the DMX Primer, which is available from the Chauvet website
www.chauvetlighting.com/download/.
When DMX linking Freedom™ Par Tri-6 products for Master/Slave operation, the DMX controller is
not a part of the DMX daisy chain and the master is the first product in the chain. See Master/Slave
Mode for details.
Starting Address
To ensure full access to all channels in each DMX mode, the highest recommended DMX address is 501.
Master/Slave
Mode
Master/Slave mode allows a single Freedom™ Par Tri-6 (the master) to control the actions of one or more
Freedom™ Par Tri-6 units (the slaves) without a DMX controller.
The master will be set to operate in either an auto program or Sound-Active mode, while the slaves will
be set to DMX starting address d 1
. Once set and connected, the slaves will operate in unison with the
master. Configure the units as indicated below.
Slaves:
1. Press <MENU> repeatedly until any DMX personality shows on the display.
2. Press <ENTER> to accept.
3. Set the DMX address to d1.
4. Connect the DMX input of the first slave to the DMX output of the master.
5. Connect the DMX input of the subsequent slaves to the DMX output of the previous slave.
6. Finish setting and connecting all the slaves.
Master:
1. Set the master to operate in either an auto program or Sound-Active mode.
2. Make the master the first unit in the DMX daisy chain.
•Configure all the slaves to Slave mode before connecting the master to the DMX daisy chain.
•Never connect a DMX controller to a DMX daisy chain of master and slaves.
•Make the master the first unit in the DMX daisy chain.
•Always put the male DMX connector (DMX Out) into the master.
•DO NOT connect more than 31 slaves to the master using DMX cable.
DMX
Personalities
When selecting a starting DMX address, always consider the number of DMX channels the selected DMX
mode uses. If you choose a starting address that is too high, you could restrict the access to some of the
product’s channels.
If unfamiliar with DMX, download the DMX Primer from www.chauvetlighting.com.
To select the DMX personality and starting address, do the following:
1. Press <MENU> repeatedly until 3-CH (3-channel mode), 4-CH (4-channel mode), 5-CH (5-channel
mode) or 9CH (9-channel mode) shows on the display.
2. Press <ENTER> and d 1–d512 shows on the display.
3. Use <UP> or <DOWN> to select the starting address.
4. Press <ENTER>.

Page 12 of 22 Freedom™ Par Tri-6 User Manual Rev. 1
D-Fi™ 2.4 GHz
(DMX Mode
Manual Sync)
The Freedom™ Par Tri-6 series offers wireless control of 2 or more products with a single DMX controller.
To manually set up the D-Fi™ 2.4 GHz syncing for DMX, do the following.
For the transmitting product:
1. Press <MENU> repeatedly until S-tr shows on the display.
2. Press <ENTER>.
3. Press <UP> or <DOWN> until dtCH appears on the display.
4. Press <ENTER>.
5. Use <UP> or <DOWN> to select the transmitting signal (dt 1–dt16).
For the receiving product(s):
1. Press <MENU> repeatedly until S-tr shows on the display.
2. Press <ENTER>.
3. Press <UP> or <DOWN> until drCH appears on the display.
4. Press <ENTER>.
5. Use <UP> or <DOWN> to select the receiving signal (dr 1–dr16). The channel number should match
the transmitting signal you chose when setting up the transmitting product.
To sync multiple transmitters in one room, manually set each receiver and the designated
transmitter to a specific frequency and then perform the syncing steps.
Freedom™ Par Tri-6 is fully compatible with the D-Fi™
2.4 GHz wireless transceiver
(transmitter/receiver) from Chauvet (sold separately).
For more detailed information about D-Fi™ 2.4 GHz functionality, refer to the D-Fi™
2.4 GHz User
Manual available at the Chauvet website www.chauvetlighting.com.
Manual syncing is recommended for best results.

Freedom™ Par Tri-6 User Manual Rev. 1 Page 13 of 22
D-Fi™ 2.4 GHz
(DMX Mode
Auto Sync)
The Freedom™ Par Tri-6 offers wireless control of 2 or more products with a single DMX controller. To
automatically set up D-Fi™ 2.4 GHz syncing for DMX, do the following:
For the receiving product(s):
1. Press <MENU> repeatedly until S-tr shows on the display.
2. Press <ENTER>.
3. Press <UP> or <DOWN> until drAS appears on the display.
4. Press <ENTER>.
5. The display should show drAU.
For the transmitting product:
1. Press <MENU>repeatedly until S-tr shows on the display.
2. Press <ENTER>.
3. Press <UP> or <DOWN> until dtAS appears on the display.
4. Press <ENTER>.
5. The display should show dtAU.
Receiving units must be set up before the transmitting unit. Once the steps above are done, press and
hold <AUTO>
on just the transmitter for approximately 30 seconds. The display and signal LED will flash
to indicate sync is activated.
You can then back out to a general menu level and configure the transmitting product to operate it with a
DMX controller.
To configure your product to work with DMX, refer to the Starting Address section.
•To add additional Freedom™ products, turn the synced ones off and repeat the above steps
with unsynced products. Once all products are synced, turn them all back on.
•Auto scan syncing must be done within a distance of about 32 ft (10 m).
•Manual syncing is recommended for best results when adding products after initial system
setup.
•If you are experiencing
issues or need to improve signal quality, keep the line of sight
between products unobstructed.
•Ensure that all linked products are configured to the same DMX personality.
Caution: D-Fi™ 2.4 GHz operation can be interrupted or inhibited by liquid masses between the
transmitter and receiver such as water, snow, or people. For best results, keep the line of sight
clear of any liquid mass.
Linking
Products
Wireless D-Fi™ Hub
DMX-compatible
Brand X product
DMX-compatible
Brand X product
Freedom™ Par sends wireless
DMX signal to DMX-
compatible products
wirelessly or via DMX cable
DMX Controller Board
To more DMX
compatible
products

Page 14 of 22 Freedom™ Par Tri-6 User Manual Rev. 1
DMX Channel
Assignments and
Values
The following tables show which DMX channels control which functions in each of the DMX personalities.
Be sure to become familiar with these values when operating the product with a DMX controller.
9-CH
Channel Function Value Setting
1
Dimmer
000 ó255
0–100%
2
Red
000 ó255
0–100%
3
Green
000 ó255
0–100%
4
Blue
000
ó
255
0–100%
5 Manual Colors and
Color Temperatures
000
ó
010
No function
011 ó030
R: 100% G: 0–100% B: 0
031 ó050
R: 100%—0 G: 100% B: 0
051 ó070
R: 0 G: 100% B: 0–100%
071
ó
090
R: 0 G: 100%–0 B: 100%
091
ó
110
R: 0–100% G: 0 B: 100%
111 ó130
R: 100% G: 0 B: 100%–0
131 ó150
R: 100% G: 0–100% B: 0–100%
151
ó
170
R: 100%–0 G: 100%–0 B: 100%
171
ó
200
R:100% G: 100% B: 100%
201 ó205
Color temperature 1
206 ó210
Color temperature 2
211
ó
215
Color temperature 3
216
ó
220
Color temperature 4
221 ó225
Color temperature 5
226 ó230
Color temperature 6
231
ó
235
Color temperature 7
236
ó
240
Color temperature 8
241 ó245
Color temperature 9
246 ó250
Color temperature 10
251
ó
255
Color temperature 11
6 Strobe
000
ó
010
No function
011 ó255
Slow to fast

Freedom™ Par Tri-6 User Manual Rev. 1 Page 15 of 22
9-CH
Channel Function Value Setting
7 Auto and Sound
Programs
000 ó010
No function
011
ó
060
Auto program 1
061
ó
120
Auto program 2
121 ó180
Auto program 3
181 ó240
Auto program 4
241
ó
255
Sound-Active mode
8
Auto Speed
000 ó255
Program speed, slow to fast
9 Dimmer Mode
000 ó051
Preset dimmer speed set in menu options
052 ó101
Dimmer speed mode off
102
ó
152
Dimmer speed mode 1, (fast speed)
153 ó203
Dimmer speed mode 2, (medium speed)
204 ó255
Dimmer speed mode 3, (slow speed)
5-CH
Channel
Function
Value
Percent/Setting
1
Dimmer
000
ó
255
0–100%
2
Red
000
ó
255
0–100%
3
Green
000
ó
255
0–100%
4
Blue
000
ó
255
0–100%
5 Strobe
000
ó
010
No function
011
ó
255
Slow to fast
3-CH
Channel
Function
Value
Percent/Setting
1
Red
000
ó
255
0–100%
2
Green
000
ó
255
0–100%
3
Blue
000
ó
255
0–100%

Page 16 of 22 Freedom™ Par Tri-6 User Manual Rev. 1
4-CH
Channel Function Value CH. 2 CH. 3 CH. 4
1
Blackout
000 ó008
Flash Speed
000 ó249
Sound-Active
250 ó255
Red
009 ó028
Green
029 ó048
Blue
049
ó
068
Green + Blue
069 ó088
Red + Blue
089 ó108
Red + Green
109 ó128
Red + Green + Blue
129
ó
143
Color Chase 1 (R + G)
144 ó152
Run Speed
Automatic
000 ó127
Sound-Active
128 ó255
Color Chase 2 (G + B)
153 ó161
Color Chase 3 (R+G+B)
162 ó170
Color Chase 4 (R+G+B+GB)
171
ó
179
Color Chase 5 (R+G+B+GB+RB)
180 ó188
Color Chase 6
(R+G+B+GB+RB+RG) 189 ó197
Color Chase 7
(R+G+B+GB+RB+RG+RGB) 198 ó206
RGB Mode 207 ó215
Red
(0–100%)
Green
(0–100%)
Blue
(0–100%)
Color Snap 216 ó224
Fade Speed
000 ó255
Color Fade 225 ó233
Fade Speed
000 ó255
Auto Run
(Sound-Active Only) 234 ó255
Run Speed
Automatic
000 ó127
Sound-Active
128 ó255

Freedom™ Par Tri-6 User Manual Rev. 1 Page 17 of 22
Configuration
(Standalone)
Use standalone configuration to operate the product without a DMX controller. There are a variety of
Standalone modes and they are powerful tools for making exciting looks.
Never connect a product operating in a standalone mode (Static, Sound-Active, Auto, or Infrared)
to a DMX chain that includes a DMX controller. Products in a
standalone mode can transmit DMX
signals that interfere with the DMX signals from the controller.
Sound-Active
Mode
Sound-Active mode sets the product to respond to sounds and music.
To enable the Sound-Active mode, do the following:
1. Press <MENU> repeatedly until Snd shows on the display.
2. Press <ENTER>.
Sound Sensitivity
To set the sound sensitivity, follow the instructions below:
1. Press <MENU> repeatedly until SenS shows on the display.
2. Use <UP> or <DOWN> to select the desired sound sensitivity (u 0–u100, low to high).
3. Press <ENTER>.
The product will respond only to low frequencies of music (bass and drums).
If the product is not responding to sound, increase the sensitivity.
Auto Programs
Auto programs set the product to 1 of 4 preset color programs.
To set the product to an auto program, do the following:
1. Press <MENU> repeatedly until P-- shows on the display.
2. Press <ENTER> and P 1–P 4 shows on the display.
3. Use <UP> or <DOWN> to select the desired auto program, P 1–P 4.
4. Press <ENTER>.
Program Speed
To set the auto program speed, follow the instructions below:
1. Press <MENU> repeatedly until S-- shows on the display.
2. Use <UP> or <DOWN> to select the desired auto program speed (S 1–S100, slow to fast).
3. Press <ENTER>.
Selecting the
Dimmer
Speed
Mode
To select a dimmer speed mode, do the following:
Press <MENU> repeatedly until dIM shows on the display.1. Press <ENTER> and one of the following shows on the display:2. •OFF (dimmer speed off)
•dIM1 (dimmer speed mode 1, fast speed)
•dIM2 (dimmer speed mode 2, middle speed)
•dIM3 (dimmer speed mode 3, slow speed)
Use <UP> or <DOWN> to select the desired dimmer speed mode.3.
Press <ENTER>.4.
Static Colors
To select a preset static color, do the following:
1. Press <MENU> repeatedly until C-- shows on the display.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to select the desired preset color (C 1–C 7).
4. Press <ENTER>.
Custom Color
Mixing
To custom mix a color, follow the instructions below:
1. Press <MENU> repeatedly until U-- shows on the display.
2. Press <ENTER> and one of the following colors shows on the display: rXXX (red), gXXX (green), or
bXXX (blue).
3. Press <ENTER> repeatedly to select the desired color.
4. Use <UP> or <DOWN> to select the desired color value (0–255).
NOTE: Selecting 0will turn the color off.
5. Press <ENTER> to select color value and continue to the next color.
6. Repeat steps 3 to 5 until you create your desired color.

Page 18 of 22 Freedom™ Par Tri-6 User Manual Rev. 1
Infrared Mode
Infrared (IR) mode allows the product to be controlled with an infrared remote controller. The
IRC-6 can remotely set the product to various modes; adjust the color, speed and sensitivity; and set the strobe.
The Freedom™ Par Tri-6 is compatible with the included IRC-6 from Chauvet. To enable use with the IRC-6,
follow the instructions below:
1. Press <MENU> repeatedly until SET shows on the display.
2. Press <ENTER> and On (turns on the infrared sensor) or OFF (turns off the infrared sensor) shows on the
display.
3. Press <UP> or <DOWN> to select the desired option.
4. Press <ENTER>.
IRC-6 Operations
Be sure the IRC-6 remote is pointing directly at the product and there is nothing in between the remote and
the product.
Automatic Mode
Automatic mode will enable you to run the automatic programs on the product.
To turn on Automatic mode:
1. Press <AUTO> on the IRC-6.
2. Press <+> or <–> to choose between the four different auto programs.
To adjust the speed of the automatic program:
1. Press <SPEED> on the IRC-6.
2. Press <%>.
3. Press <+> or <–> to either increase or decrease the speed of the program.
Sound-Active Mode
Sound-Active mode will enable the product to respond to the music.
To turn on Sound-Active mode:
•Press <SOUND> on the IRC-6.
To adjust sound sensitivity in Sound-Active mode:
1. Press <SENSITIVITY> on the IRC-6.
2. Press <%>.
3. Press <+> or <–> to either increase or decrease sound sensitivity.
Manual Color Control
To choose a specific color with the IRC-6:
1. Press <MANUAL> on the IRC-6.
2. Press any number between <0> and <9> to choose your color.
To manually control the RGB percentage:
1. Press <MANUAL> on the IRC-6.
2. Press <R>, <G>, or <B> (red, green, or blue) to choose your color.
Note: The Freedom™ Par Tri-6 only contains red, green, and blue LEDs. The amber,
white, and UV
color options on the IRC-6 will only operate with fixtures capable of outputting these color lights.
3. Press <+> or <–> to increase or decrease the percentage of each color.
Miscellaneous Operation
To adjust the strobe rate of the program:
1. Press <STROBE> on the IRC-6.
2. Press <+> or <–> to increase or decrease the strobe rate.
3. Press <STROBE> again to turn off the strobe.
To choose a fade auto program:
•Press <FADE> repeatedly on the IRC-6 to choose between the two auto program fade options
To black out the lights:
•Press <BLACK OUT> on the IRC-6. This will turn off all the lights until the button is pressed again.
Note: The IRC-6 will not respond to any inputs when the Black Out mode i
s activated. If the remote does not respond when a button
is pressed, try pressing <BLACK OUT>. You may have inadvertently activated the Black Out mode.

Freedom™ Par Tri-6 User Manual Rev. 1 Page 19 of 22
5. TECHNICAL INFORMATION
Product
Maintenance
Dust build-up reduces light output performance and can cause overheating. This can lead to reduction of
the light source’s life. To maintain optimum perf
ormance and minimize wear, clean the product at least
twice a month. However, usage and environmental conditions may require more frequent cleaning.
To clean the product, follow the instructions below:
1. Unplug the product from power.
2. Wait until the product is at room temperature.
3. Use a vacuum (or dry compressed air) and a soft brush to remove dust collected on the external
surfaces and vents.
4. Clean all external optics and transparent surfaces with a mild soap solution, ammonia-free glass
cleaner, or isopropyl alcohol.
5. Apply the solution directly to a soft, lint-free cotton cloth or a lens cleaning tissue.
6. Softly wipe any dirt or grime to the outside edges of the external optics or transparent surface.
7. Gently polish the external optics and transparent surfaces until they are free of haze and lint.
Always dry the lens surfaces carefully after cleaning them.

Page 20 of 22 Freedom™ Par Tri-6 User Manual Rev. 1
6. TECHNICAL SPECIFICATIONS
Dimensions and
Weight
Length
Width
Height
Weight
5.4 in (138 mm)
5.7 in (145 mm)
7.2 in (184 mm)
5.8 lb (2.6 kg)
Note: Dimensions in inches rounded to the nearest decimal digit.
Power
Input Voltage
Range
Voltage Selection
Switching (internal)
100–240 VAC, 50/60 Hz
Auto-ranging
Parameter
120 VAC, 60 Hz
230 VAC, 50 Hz
Consumption
32 W
31 W
Operating current
0.5 A
0.3 A
Power linking current (units)
8 A (17 units)
8 A (30 units)
Fuse
T 1 A, 250 V
T 1 A, 250 V
Power I/O
US/Canada
UK/Worldwide
Power input connector
IEC
IEC
Power output connector
Edison
IEC
Power cord plug
Edison (US)
Local plug
LED
Type
Power
Lifespan
LED
3 W
50,000 hours
Color
Quantity
Current
Tri-color RGB
6
600 mA
Photo Optic
Parameter
Field angle
29°
Beam angle
15°
Strobe rate
0 to 17 Hz
Illuminance @ 2 m
1,938 lux
Thermal
Maximum External Temp.
Cooling System
104 °F (40 °C) Convection
DMX
I/O Connectors
Connector Type
Channel Range
3-pin XLR
Sockets
3, 4, 5 or 9
Ordering
Product Name
Item Code
UPC Number
Freedom™ Par Tri-6
03030812
781462211608