Cisco 7975G - Unified IP Phone VoIP Manual

Cisco Unified IP Phone 7975G
Admin Guide
Schmooze Com Inc.
1
#
*
4
0
2
ABC
3
DEF
6
MNO
GHI
5
JKL
7
PQRS
8
TUV
9
WXYZ
+
-
?
11:18 07/11/07
9208868130
Schmooze Com, Inc.
Your current options
Redial
New Call
CFwdAll
Mobility
Cisco IP Phone
7975

Chapters
How to Find the IP Address
How to Find the MAC Address
How to Set the Configuration Server
How to Restore Factory Default
© Copyright Schmooze Com, 2013
How to Find the IP Address
Quick Steps
1. Press the Settings button.
2. Highlight Network Configuration and press Select.
3. Then press Select for the first option, which is IPv4 Configuration.
4. The IP Address should display as the second option.
How to Find the MAC Address
Quick Steps
1. Press the Settings button.
2. Highlight Model Information and press Select.
3. The MAC Address should display as the second option under the model number of the phone.
How to Set the Configuration Server
Quick Steps
1. Cisco Enterprise phones do not support setting the configuration server through either the
phone or the web GUI. The only way to make the phone grab a configuration file is to setup
your DHCP server to point option 66 to the IP Address of your PBX.
How to Restore Factory Default
Quick Steps
1. Unplug the power cable from the phone and then plug it back in. The phone will begin its
power-up cycle.
2. While the phone is powering up, and before the Speaker button flashes on and off, press and
hold #. Continue to hold # until each line button flashes on and off in sequence in amber.
3. Release # and press 123456789*0#. After you press these keys, the line buttons on the
phone flash red, and the phone goes through the factory default process. Do not power down
the phone until this process is complete.

Chapters
How to Find the IP Address
How to Find the MAC Address
How to Set the Configuration Server
How to Restore Factory Default
How to Find the IP Address
Quick Steps
1. Press the Settings button.
2. Highlight Network Configuration and press Select.
3. Then press Select for the first option, which is IPv4 Configuration.
4. The IP Address should display as the second option.
© Copyright Schmooze Com, 2013
How to Find the MAC Address
Quick Steps
1. Press the Settings button.
2. Highlight Model Information and press Select.
3. The MAC Address should display as the second option under the model number of the phone.
How to Set the Configuration Server
Quick Steps
1. Cisco Enterprise phones do not support setting the configuration server through either the
phone or the web GUI. The only way to make the phone grab a configuration file is to setup
your DHCP server to point option 66 to the IP Address of your PBX.
How to Restore Factory Default
Quick Steps
1. Unplug the power cable from the phone and then plug it back in. The phone will begin its
power-up cycle.
2. While the phone is powering up, and before the Speaker button flashes on and off, press and
hold #. Continue to hold # until each line button flashes on and off in sequence in amber.
3. Release # and press 123456789*0#. After you press these keys, the line buttons on the
phone flash red, and the phone goes through the factory default process. Do not power down
the phone until this process is complete.
11:18 07/11/07
9208868130
Schmooze Com, Inc.
Your current options
Select
Exit
7975G Settings
User Preferences1
2Network Configuration
Device Configuration
Security Configuration
3
4
Model Information5
11:18 07/11/07
9208868130
Schmooze Com, Inc.
Your current options
Select
Exit
Network Configuration
IPv4 Configuration1
2IPv6 Configuration
MAC Address
Host Name
3
4
B4E8B09CDE4D
11:18 07/11/07
9208868130
Schmooze Com, Inc.
Your current options
Exit
IPv4 Configuration
IP Address2
10.10.0.1
1DHCP
Enabled
3Subnet Mask
255.255.255.0

Chapters
How to Find the IP Address
How to Find the MAC Address
How to Set the Configuration Server
How to Restore Factory Default
How to Find the IP Address
Quick Steps
1. Press the Settings button.
2. Highlight Network Configuration and press Select.
3. Then press Select for the first option, which is IPv4 Configuration.
4. The IP Address should display as the second option.
How to Find the MAC Address
Quick Steps
1. Press the Settings button.
2. Highlight Model Information and press Select.
3. The MAC Address should display as the second option under the model number of the phone.
How to Set the Configuration Server
Quick Steps
1. Cisco Enterprise phones do not support setting the configuration server through either the
phone or the web GUI. The only way to make the phone grab a configuration file is to setup
your DHCP server to point option 66 to the IP Address of your PBX.
© Copyright Schmooze Com, 2013
How to Restore Factory Default
Quick Steps
1. Unplug the power cable from the phone and then plug it back in. The phone will begin its
power-up cycle.
2. While the phone is powering up, and before the Speaker button flashes on and off, press and
hold #. Continue to hold # until each line button flashes on and off in sequence in amber.
3. Release # and press 123456789*0#. After you press these keys, the line buttons on the
phone flash red, and the phone goes through the factory default process. Do not power down
the phone until this process is complete.
11:18 07/11/07
9208868130
Schmooze Com, Inc.
Your current options
Select
Exit
7975G Settings
Network Configuration2
3Device Configuration
Security Configuration
Model Information
4
5
Status6
11:18 07/11/07
9208868130
Schmooze Com, Inc.
Your current options
Exit
Model Information
MAC Address2
B4E8B09CDE4D
1Model Number
CP-7975G
3Load File
*term75 default*

Chapters
How to Find the IP Address
How to Find the MAC Address
How to Set the Configuration Server
How to Restore Factory Default
How to Find the IP Address
Quick Steps
1. Press the Settings button.
2. Highlight Network Configuration and press Select.
3. Then press Select for the first option, which is IPv4 Configuration.
4. The IP Address should display as the second option.
How to Find the MAC Address
Quick Steps
1. Press the Settings button.
2. Highlight Model Information and press Select.
3. The MAC Address should display as the second option under the model number of the phone.
How to Set the Configuration Server
Quick Steps
1. Cisco Enterprise phones do not support setting the configuration server through either the
phone or the web GUI. The only way to make the phone grab a configuration file is to setup
your DHCP server to point option 66 to the IP Address of your PBX.
How to Restore Factory Default
Quick Steps
1. Unplug the power cable from the phone and then plug it back in. The phone will begin its
power-up cycle.
2. While the phone is powering up, and before the Speaker button flashes on and off, press and
hold #. Continue to hold # until each line button flashes on and off in sequence in amber.
3. Release # and press 123456789*0#. After you press these keys, the line buttons on the
phone flash red, and the phone goes through the factory default process. Do not power down
the phone until this process is complete.
© Copyright Schmooze Com, 2013
#

Schmooze Com Inc.
http://schmoozecom.com
[phone]