Target Windham WNCBDW2DBK User manual

>>
© 2019 Target. The Bullseye Design is a trademark of Target Brands, Inc. All rights reserved.
windham
accent cabinet with drawer
assembly instructions
style # WNCBDW2DBK (black)
dpci # 249-16-0022
style # WNCBDW2DRD (red)
dpci # 249-16-0023
style # WNCBDW2DBL (teal)
dpci # 249-16-0021
style # WNCBDW2DGY (grey)
dcpi # 249-16-0026
style # WNCBDW2DWH (shell)
dpci # 249-16-0013
style # WNCBDW2DYL (yellow)
dpci # 249-16-0029
style # WNCBDW2DGG (green garnish)
dpci # 249-16-4302
style # WNCBDW2DOV (overcast)
dpci # 249-16-4306
style # WNCBDW2DBN (banana split)
dpci # 249-16-4315

2
Congratulations on your latest Target purchase.
Now what? Don’t start sweating over this box of parts. This will be easy. We did the hard work for you.
All you need to do is follow our simple instructions and you’ll be on your way to transforming your
room in no time. Good luck—though we’re condent you won’t need it.
before you begin
1. Check for damaged or missing parts. Call 1-855-MYTGTHOME (855-698-4846) to order missing supplies.
2. Use the carton as a working surface to prevent product damage during assembly.
3. Gather all tools prior to assembly.
tools needed

3
table of contents
introduction 2
hardware 4-5
parts list 6
how to use the cam lock system 7
assembly 8-17
how to adjust door alignment 18
QUESTIONS? Just call 1-855-MYTGTHOME (855-698-4846) for parts and service. For faster service, have the style number and DPCI number ready when calling.

4
hardware
(H1) x 16
wooden dowel
(H2) x 6
cam bolt
(H3) x 6
cam
(H4) x 4
bolt
(H5) x 6
washer
(H6) x 4
lock washer
(H7) x 1
allen wrench
(H8) x 19
5/8’’ pan-head screw
(H9) x 4
knob
(H10) x 4
knob bolt
(H11) x 8
short at-head screw
(H12) x 4
shelf supports
(H13) x 2
small cam bolt
(H14) x 2
small cam
(H15) x 8
long at-head screw

5
hardware
(H16) x 1
wall anchor
(H17) x 1
38mm wall screw
(H18) x 1
wall strap
(H19) x 1
19mm pan-head screw

66
exploded diagram
ITEM DESCRIPTION QUANTITY
1 top panel 1
2 left side panel 1
3 right side panel 1
4 bottom panel 1
5 adjustable shelf 1
6 left door 1
7 right door 1
8 back panel 1
9 trim 1
10 drawer front 1
11 left drawer side 1
12 right drawer side 1
13 drawer back 1
14 drawer panel 1
15 drawer rail 1

how to use the cam lock system
1.
Screw cam bolt into panel
2.
Align cam bolt(s) with cross-bored
hole(s) and insert all the way until
panels are ush
3.
Push cam into panel - arrow feature
on cam top points to panel edge
4.
Rotate cam(s) clockwise 180° to
lock panels together
5.
Panels should be tight against each
other and connection should be rigid
7
4. 5.
1. 2. 3.

step 1: attach trim and bottom panel to left side panel
(H1) x 4
wooden dowel
(H2) x 3
cam bolt
(H3) x 3
cam
1.1. Carefully tap small wooden dowels into place in left side panel. Leave 1/2” of the dowels sticking out.
1.2. Screw-In cam bolts must be screwed down ush in left side panel.
1.3. Refer to page 7 for instructions on how to use the cam lock system. Do not over tighten bolts.
8
nished edge

step 2: attach right side panel
(H1) x 4
wooden dowel
(H2) x 3
cam bolt
(H3) x 3
cam
2.1. Carefully tap small wooden dowels into place in right side panel. Leave 1/2” of the dowels sticking out.
2.2. Screw-In cam bolts must be screwed down ush in right side panel.
2.3. Refer to page 7 for instructions on how to use the cam lock system. Do not over tighten bolts.
9

step 3: attach top panel
(H1) x 4
wooden dowel
(H4) x 4
bolt
(H5) x 4
washer
(H6) x 4
lock washer
(H7) x 1
allen wrench
3.1. Carefully tap small wooden dowels into place in top panel. Leave 1/2” of the dowels sticking out.
3.2. Align bolts with pre-drilled holes to attach side panels to top panel. Do not over tighten bolt.
1010

step 4: attach back panel
**FAILURE TO FOLLOW ALL DIRECTIONS ON THIS PAGE MAY RESULT IN UNEVEN DOOR ALIGNMENT**
Begin by installing all of the screws along one
edge of the back panel. Next, using a square
or tape measure, make sure that the cabinet is
square. (If using a tape measure, the distance
from one corner, diagonally to the other corner
should be the same in both directions.) If not,
apply gentle pressure to the diagonally opposite
corners to shift case into alignment. Re-measure
to ensure equal distances. Install the remaining
screws, starting with the corners.
(H8) x 19
5/8’’ pan-head
screw
4.1. Make sure the pan-head screws go through the pre-drilled holes properly to attach back panel. Do not over tighten screws.
11
hole for anti-tip strap
pre-drilled holes

step 5: attach knobs to doors
(H9) x 2
knob
(H10) x 2
knob bolt
5.1 Align knob bolts with pre-drilled holes to attach knobs to doors. Do not over tighten bolts.
12

step 6: attach doors to cabinet
(H11) x 8
short at-head
screw
6.1 Align at-head screws with pre-drilled holes to attach doors to cabinet. Do not over tighten screws.
13

step 7: install adjustable shelves
(H12) x 4
shelf supports
7.1. Insert shelf supports into desired hole. Di󰀨erent holes accommodate di󰀨erent shelf heights.
7.2. Angle shelf to t between the rails and set on top of shelf supports.
14
7.1.
7.2. Angle shelf to t between the rails and set on top of shelf supports.
Insert shelf supports into desired hole. Di󰀨erent holes accommodate di󰀨erent shelf heights.

step 8: assemble drawer box
(H1) x 4
wooden dowel
(H13) x 2
small cam bolt
(H14) x 2
small cam
(H15) x 8
long at-head
screw
8.1. Align at-head screws with pre-drilled holes to attach drawer sides to drawer front. Do not over tighten screws.
8.2. Carefully tap small wooden dowels into place in drawer front and drawer back. Leave 1/2” of the dowels sticking out.
8.3. Screw-In cam bolts must be screwed down ush in drawer front and drawer back.
8.4. Refer to page 7 for instructions on how to use the cam lock system. Do not over tighten bolts.
8.5. Align at-head screws with pre-drilled holes to attach drawer back. Do not over tighten screws.
51
arrowed sticker will point to
the back side of drawer face.
Align at-head screws with pre-drilled holes to attach drawer sides to drawer front. Do not over tighten screws.
Carefully tap small wooden dowels into place in drawer front and drawer back. Leave 1/2” of the dowels sticking out.

step 9: install drawer and knob
(H9) x 2
knob
(H10) x 2
knob bolt
9.1 Align knob bolts with pre-drilled holes to attach knobs to drawer. Do not over tighten bolts.
9.2 Align tracks on drawer box with tracks on left side panel and right side panel.
16

step 10: install anti-tip kit
(H16) x 1
wall anchor
(H17) x 1
38mm wall screw
(H18) x 1
wall strap
(H5) x 2
washer
(H19) x 1
19mm pan-head screw
Position against wall
Mark position of strap hole on
wall
Drill 1/4’’ hole
Tap in wall anchor
Fasten anti-tip strap
with at-head screw provided
17
(H18)
(H19)
(H5)
(H17) (H5)
(H16)
Mark position of strap hole on
wall
Fasten anti-tip strap
with at-head screw provided

how to adjust door alignment
Tips for proper door alignment:
-Adjustable levelers will reduce minor door mis-alignments
caused by an uneven oor.
-Use a level to determine if the cabinet top is level. If not, start
with the levelers retracted and adjust them as needed.To
retract the levelers turn them counterclockwise. To extend
the levelers turn them clockwise.
-If door mis-alignment persists, refer back to Step 4 (pg. 11)
for additional information. If the cabinet is not square you will
need to repeat this step.
1818
adjustable leg levelers


  
   

  
   
 
 

     
 
 

  

 
 
   
1. This unit has been designed for the weight shown. Exceeding this recommended weight could result in
excessive “sagging” of the top. Extreme overloading can cause failure of the top and possible injury.
2. Furniture Care Instructions: Dust with a clean, lint-free cloth. Use a spray furniture polish as needed.
19
QUESTIONS? Just call 855-MYTGTHOME (855-698-4846) for parts and service. For faster service, have the style number and DPCI number ready when calling.
80 lbs.
15 lbs.


© 2019 Target. The Bullseye Design is a trademark of Target Brands, Inc. All rights reserved.