CombiSteel 7178.1105 Instructions for use

BANQUET TROLLEY
(ELECTRICAL)
INSTRUCTION AND
MAINTENANCE MANUAL

DESCRIPTION
Our dear customer,
Your preferred COMBISTEEL is nature and technology friendly. We thank you for your choice.
COMBISTEEL has been produced with the understanding of "Total Quality" in modern production
facilities.
Important Safety Information
Carefully read this guide and keep itfor future review.
WARNING: Installation of the devices must be done byan authorized service person.
Indicates that there is a risk of personal injury or property damage.
Explosion / fire hazard.
The instructions in this manual contain important information on the safe mounting, usage, cleaning
and maintenance of the device. Thus, keep the manual at a place easily accessible by the person who
will use the machine, and the technician.
Mounting, electrical connection and maintenance works of the device should be performed by a
specialist authorized in this subject and in accordance with the instructions of the manufacturer
company.
TYPES
7178.1105 –Single door banquet trolley
7178.1100 –Single door banquet trolley
MOUNTING
Placement
Installation and adjustment of the device should be carried out by authorised technical staff.
Place the device at a place min. 10cm away from the side or back wall to prevent excessive
temperature increment.
Remove the nylon protection cover on the device. If there are any adhesive residues left on the
surface, clean with a suitable solvent.
Device should be placed on a flat surface by suitably balancing on the four adjustable legs (fig.A
ELECTRICALCONNECTION
Connect the device to the electrical installation according to the electrical standards of the relevant
country.
Feed the device with suitable voltage written on the information plate.
The cable connecting the device to the electrical installation should be at least type H05 RNF.

Voltage tolerance should not exceed ± 10%.
Electrical inlet is indicated with a label on the device.

If the device will be used in a commercial kitchen, apply a correct grounding system. Here, consider
DIN VDE D100 Article 540.
The device must be grounded. - Grounding point is marked with " ".
USAGE AND MAINTENANCE
INSTRUCTIONS
WARNINGS
IMPORTANT: make sure the electrical connection is cut off before attempting to do any
maintenance.
Pay attention not to contact hot surfaces of the device!
Device is designed for professional use and must be used only by person who are trained for this
intention.
Device is intended for keeping the hot temperature, do not use for another purpose.
If there is any failure in the device, disconnect electrical power by deactivating the main switch.
Commission only authorized services for maintenance and use genuine spare parts.
Before starting to use the device, carefully clean the surfaces especially those to be in contact with
foods.
During first operation, device will emit fume and smell for a short period. This fume and smell is the
result of the insulation material and the substances such as oil, etc. on the metal sheet surfaces. This
is not dangerous and will disappear by itself.
Operate the device at the highest operation level for 1 hour during first operation.
MAINTENANCE
Do not wash the device with high pressurized water.
You must switch off the electrical connection of the device before starting to cleaning or
maintenance activities.
Before it cools down completely, wipe the device with a cloth immersed in warm soapy water at the
end of each working day.
During cleaning the device surface, do not use corrosive material which may cause scratches on the
surface such as detergents, wire brushes, etc.
Clean the surfaces, which cannot be cleaned through abovementioned methods, with chemical
solvents.
Please remove the installations located at the bottom of the unit to clean it with vapour or water.
Otherwise the electrical systems might be damaged.
In case of any extraordinary condition with the device, notify to the authorized service. Never allow
unauthorized people to interfere in the device.
START-UP
Starting-up thedevice
Activate the main switch to which the device is connected.
Activate on-off switch.
Adjust thermostat control button to desired cooking temperature. The temperature value can be seen
on the display on the control panel. (B-3)
To adjust the temperature, press the SET 5 button for 2 seconds. When the temperature value is
blinking, press the button (7).
For all other settings, please contact the authorised service.
Switching-off thedevice
Turn thermostat control button to position ''0''.
Plug the device off.
Limitation of Liability: All technical information contained in this manual, operating instructions,
operation and maintenance of the device, contains the latest information on your device. The
manufacturer accepts no responsibility for damage or injury which may result from failure to follow
the instructions in this manual, use outside of the intended use, unauthorized repair, unauthorized
modifications to the device, or use of spare parts not approved by the manufacturer.

TableA
Figure A
1234
57
6
Figure B Figure C
MODEL
7178.1105
7178.1100
Width (A)
mm
625
1310
625
Dept (B)
mm
845
845
845
Hight (C)
mm
1890
1890
1660
Power
KW
2
2
2
Electrical Inlet
230V N PE
230V N PE
230V N PE
Cable Sections
mm²
3X 1,5
3X 1,5
3X1,5
Tray Capacity
piece
18 pcs Gn2/1x65
36 pcs Gn1/1x65
36 pcs Gn2/1x65
72 pcs Gn1/1x65
15 pcs Gn2/1x65
30 pcs Gn1/1x65

1- On-off button
2- Panel handle
3- Digital display
4- Plug
5- Set button
6- Heat increase
7- Heat decrease
7178.1105
845
1890
625
805 925
7178.1105
,

845
1890
1310
1490 925
7178.1100

7178.1105 –230V AC N PE 2000W
7178.1100 –230V AC N PE 2000W
x
L
N
X - TERMİNAL BOARD
F1- FAN
Q1- CUT-OFF SWITCH
R1- HEATING ELEMENT
EXPLANATION
D1- DIGITAL CONTROL (XR20CX)
L
N
PE
Q1
4
5
7
8
12
11
9
Supply
D
1
R
1
F
1

Note: If required, you can send it to our company by viewing the
form above or by post.
EVALUATION:
APPROVERS
SOLUTION PROPOSAL:
DATE:
PROBLEM DESCRIPTION:
SIGN:
PRODUCT NAME:
DETECTED ( Name , Appellation)
CUSTOMER
NAME
CUSTOMER COMPLAINT
DETECTION TYPE
CORRECTIVE \PREVENTIVE ACTIVE FORM
OPTIMIZATION REQUEST/
DESCRIPTION