Comelit UT8010 User manual

Passion.Technology.Design.
EN
TECHNICAL
MANUAL
Ultra audio module, IP (ViP) system
Art. UT8010

2
Warning
Intended use
This Comelit product has been designed and manufactured for use in the creation of audio and video communication
systems in residential, commercial, industrial and public buildings.
Installation
All activities connected to the installation of Comelit products must be carried out by qualified technical personnel, with
careful observation of the indications provided in the Manuals / Instruction sheets supplied with those products.
Wires
Disconnect the power supply before carrying out any operations on the wiring.
Use wires with a cross-section suited to the distances involved, observing the instructions provided in the system
manual.
We advise against running the system wires through the same duct as power cables (230V or higher).
Safe usage
To ensure Comelit products are used safely:
• carefully observe the indications provided in the Manuals / Instruction sheets,
• make sure the system created using Comelit products has not been tampered with / damaged.
Service
Comelit products do not require maintenance aside from routine cleaning, which should be carried out in accordance
with the indications provided in the Manuals / Instruction sheets.
Any repairs must be carried out:
• for the products themselves, exclusively by Comelit Group S.p.A.,
• for the systems, by qualified technical personnel.
Disclaimer
Comelit Group S.p.A. does not assume any responsibility for
• any purpose other than the intended use,
• failure to observe the indications and warnings contained in this Manual / Instruction sheet.
Comelit Group S.p.A. reserves the right to change the information provided in this Manual / Instruction Sheet at any
time and without prior notice.

3
Table of contents
Warning ............................................................................................ 2
Description....................................................................................... 4
UT8010 ......................................................................................................4
Technical specifications ................................................................. 6
Installation........................................................................................ 7
Flush-mounted installation composition table....................................7
Surface-mounted installation composition table................................8
Flush-mounted installation............................................................. 9
Removing nameplates (2A) / module (2B)............................................10
Installation with side-by-side boxes.....................................................11
Wall-mounted installation............................................................. 12
Optional .......................................................................................... 12
Removing nameplates (2A) / module (2B)............................................13
Installation with side-by-side boxes.....................................................14
Connections................................................................................... 15
Connection with power supply from floor distribution unit 1440 ......15
Connection with power supply from standard POE switch ...............15
Connection with separate power supply .............................................16
Connection with separate power supply and non-POE switch .........16
Variant for using the external entrance panel relay ............................17
Variant with safety door lock ................................................................17
Module connection........................................................................ 18
Outdoor entrance panel module consumption table .........................18
power supply from floor distribution unit Art. 1440 or from standard
PoE....................................................................................................18
power supply with additional power supply unit Art. 1595 or Art.
1596B................................................................................................18
Connection of button modules Art. UT9200.....................................19
Connection of Touchscreen module Art. UT9270.............................19
Connection of Touchscreen module Art. UT9270 with additional power
supply unit ........................................................................................20
Connection of number keypad module Art. UT9279M.....................20
Programming ................................................................................. 21
Address button modules .......................................................................21
First startup or restarting ......................................................................21
Adjusting the brightness of the button LEDs .....................................22
Reset to factory values..........................................................................23
Programming via ViP Manager..................................................... 24
Connections available for programming via ViP Manager.................24

4
UT8010
Audio module for Ultra entrance panel, IP (ViP) system.
Twilight sensor for automatic nameplate backlighting power-off during daytime hours. Omnidirectional digital
microphone and double loudspeaker for high-fidelity audio.
Audio-visual indications for disabled individuals assistance request can be activated via programming.
Facility for 2 call buttons. To be finished with cap, single button or dual button made using aluminium or professional
grade plastic treated to prevent yellowing and dulling.
Adjustment and programming can take place without removing the module.
Dimensions: 1 Ultra module.
ULTRA: the new and most technologically advanced entrance panel offering maximum ease of installation.
Available in flush-mounted (10 mm protrusion from the wall) or surface-mounted (just 35 mm protrusion from the wall)
variants.
Description

5
1
2
6. 7. 8.
4. 5. 3.
1. 2. 2.
9.
1. Indicator LEDs
calling (green)
system busy (red)
first startup or restart (flashing red)
lock-release enabled
communication enabled
2. Loudspeakers
3. Twilight sensor
4. Button for starting the reset procedure and adjusting the
backlighting
5. Digital microphone
6. Terminal block for connection:
RTE programmable input: RTE (local
lock-release input), DO (door open
indication), Activate output, Priority call
or Call user
GND SE- RTE and door lock input reference
negative
SE+ electric door lock connection
NO NC COM relay contacts
V- V+ 33 VDC power supply (Art.1595,
Art.1596B)
7. Ethernet terminal block
- + 36-57 VDC power supply, standard PoE
TX- TX+ Ethernet transmission line terminals
RX- RX+ Ethernet receipt line terminals
8. Connector for additional modules with LAN
9. Connector for additional module connection

6
Technical specifications
GENERAL DATA
Type Modular
Product height (mm) 90
Product width (mm) 100
Product depth (mm) 35
Product colour Black RAL9005, Transparent, Aluminium
Material Polycarbonate, Aluminium alloy
Flush mounting Yes, with specific accessory
Surface mounting Yes, with specific accessory
COMPATIBLE SYSTEMS
ViP Yes
AUDIO SPECIFICATIONS
Microphone MEMS digital audio sensor, omnidirectional
Loudspeaker 28 mm (Ø), 8 Ohm, 1W (2)
Technologies implemented Echo cancelling
ELECTRICAL SPECIFICATIONS
Type of power supply PoE, external power supply
PoE power supply 36-57 VDC, standard PoE
PoE Class Class 0
HARDWARE CHARACTERISTICS
Call type Buttons
Type of buttons Mechanical
Number of buttons (no.) 2
Backlighting colour White, O
Terminals TX- TX+ RX- RX+ V- V+ RTE GND/SE- SE+ COM NC NO
Removable terminals Yes
Number of inputs (no.) 1
Number of outputs (no.) 2
Communication port Ethernet
Twilight sensor Ye s
SETTINGS
Loudspeaker volume Yes
Mic volume Yes
Backlighting brightness Yes
NETWORK AND COMMUNICATION
PROTOCOL
LAN type Ethernet 10 Mbit/s
IP address assignment Auto IP, DHCP, Static
PROGRAMMING MODE
ViP Manager software Yes
ENVIRONMENTAL AND CONFORMITY
SPECIFICATIONS
Operating temperature (°C) -25 to 55
Operating humidity (max RH - %) 25 to 95
MAIN FUNCTIONS
Lock-release Yes
Number of auxiliary relays (no.) 2
Input for local key button Yes
Input for door open signal Yes
System status visual indications Yes
System status audio indications Yes
System status voice synthesis Yes

7
Installation
A = Flush-mounted box
B = Rain shield
C = Flush-mounted module holder with finishing frame
Flush-mounted box
3110/1
3110/1A
3110/2
3110/2A
3110/3
3110/3A
3110/4
3110/4A
Rain shield
UT9181 UT9182 UT9184H UT9183 UT9186 UT9189 UT9184 UT9188
Module holder/ finishing frame
UT9161 UT9162 UT9163 UT9164
Optional
The entrance panel is available in flush-mounted or surface-mounted variants:
Flush-mounted installation composition table

8
A = Rain shield
B = Surface-mounted housing with frame
Rain shield UT9191 UT9192 UT9194H UT9193 UT9196 UT9199 UT9194 UT9198
Housing/frame
UT9171 UT9172 UT9174H UT9173 UT9176 UT9179 UT9174 UT9178
Optional
Surface-mounted installation composition table

9
2
1
2
53 4
165 cm
130 cm
1
Flush-mounted installation
Optional
BLACK
Optional
RED

10
6
1
A
B
C
C
2
+ Art. UT9110
MAX 0,2 mm
MAX 0,2 mm
9
2
1
11 12
1
2
10
CLACK!
CLACK!
1
2
3CLACK!
8
CLACK!
CLACK!
CLACK!
1
2
3
7
1
2
3
1
2
3
1
2A
1
3
2
4
2B
Removing nameplates (2A) / module (2B)
CLOSE
The button has a nameplate which can be written on (A);
alternatively, an adhesive label can be applied (B).
The total thickness of the nameplate + adhesive label
must not exceed 0.2 mm.
You can visit the website pro.comelitgroup.com to download
the PDF to print the entrance panel name cards, using the pre-
cut sheets (C) available in our catalogue (Art. UT9110 ).
Custom engraved Full Metal Ultra nameplates are available
on request. Find out how:
https://pro.comelitgroup.com/en-gb/customised-
nameplates-for-ultra-entrance-panel
Kit Art. UT9110 contains 5 sheets of pre-cut labels for nameplates and 1 sheet for the information module.
The sheets are made using Yupo paper which oers the ultimate transparency and resistance to atmospheric agents over time.
To print the labels, use the editable .pdf file which is available to download free of charge from the website pro.comelitgroup.com

11
Installation with side-by-side boxes
Before installing the boxes in the wall, fit the spacers.

12
165 cm
130 cm
2
53 4
UP
1
2
3
1
Wall-mounted installation
Optional
BLACK
RED
Optional

13
6
1
A
B
C
C
2
+ Art. UT9110
MAX 0,2 mm
MAX 0,2 mm
9
2
1
11 12
1
2
10
CLACK!
CLACK!
1
2
CLACK!
3
8
CLACK!
CLACK!
1
2
CLACK!
3
7
1
2
3
1
2
1
3
2A
1
3
2
4
2B
Removing nameplates (2A) / module (2B)
CLOSE
The button has a nameplate which can be written on (A);
alternatively, an adhesive label can be applied (B).
The total thickness of the nameplate + adhesive label
must not exceed 0.2 mm.
You can visit the website pro.comelitgroup.com to download
the PDF to print the entrance panel name cards, using the
pre-cut sheets (C) available in our catalogue (Art. UT9110 ).
Custom engraved Full Metal Ultra nameplates are available
on request. Find out how:
https://pro.comelitgroup.com/en-gb/customised-
nameplates-for-ultra-entrance-panel
Kit Art. UT9110 contains 5 sheets of pre-cut labels for nameplates and 1 sheet for the information module.
The sheets are made using Yupo paper which oers the ultimate transparency and resistance to atmospheric agents over time.
To print the labels, use the editable .pdf file which is available to download free of charge from the website pro.comelitgroup.com

14
Installation with side-by-side boxes

15
ORANGE
BLUE & WHITE BLUE
BROWN & WHITE BROWN
WHITE ORANGE
GREEN
WHITE GREEN
++
-
+
-
TX
1440
L N
-
+
V V
1441
OUT
43
OUTOUT
21
IN
21
IN
+
-
OUT
GND
SE- SE+
NO NC
C
O
M
R
T
E
+
-
+
VV
- - -
TX TX
+
RX RX
+
UT8010 UT9200
(MAX 10)
ORANGE
BLUE & WHITE BLUE
BROWN & WHITE BROWN
WHITE ORANGE
GREEN
WHITE GREEN
++
-
+
-
TX
GND
SE- SE+
NO NC
C
O
M
R
T
E
+
-
+
VV
- - -
TX TX
+
RX RX
+
UT8010 UT9200
POE
STANDARD
SWITCH
Connections
Connection with power supply from floor distribution unit 1440
Connection with power supply from standard POE switch
Max 20 m. Local door-opener button.
Max 20 m. Local door-opener button.

16
14411441
L N
-
+
V V
ORANGE
WHITE ORANGE
GREEN
WHITE GREEN
++
-
TX
1440
1440
OUT
43
OUTOUT
21
IN
21
IN
+
-
OUT
-
+
120-230 V
1595
GND
SE- SE+
NO NC
C
O
M
R
T
E
+
-
+
VV
- - -
TX TX
+
RX RX
+
UT8010 UT9200
(MAX 15)
++
--
120-240 V
1596B
NC
C
O
M
+
-
+
VV
- - -
TX TX
+
RX RX
+
UT8010 UT9200
(MAX 30)
N L
ORANGE
WHITE ORANGE
GREEN
WHITE GREEN
++
-
TX
-
+
120-230 V
1595
GND
SE- SE+
NO NC
C
O
M
R
T
E
+
-
+
VV
- - -
TX TX
+
RX RX
+
UT8010 UT9200
NON POE
ETHERNET
SWITCH
Connection with separate power supply
Connection with separate power supply and non-POE switch
Max 20 m. Local door-opener button.
Max 20 m. Local door-opener button.

17
GND
SE- SE+
NO NC
C
O
M
R
T
E
+
-
+
VV
- - -
TX TX
+
RX RX
+
UT8010 UT9200
4A MAX
AC-DC
12V/24V
GND
SE- SE+
NO NC
C
O
M
R
T
E
+
-
+
VV
- - -
TX TX
+
RX RX
+
UT8010 UT9200
12/24V
AC/DC
Variant for using the external entrance panel relay
Variant with safety door lock

18
+-
ORANGE BLUE & WHITE BLUE BROWN & WHITE BROWN WHITE ORANGE GREEN WHITE GREEN
++ - + -
TX
V+V-
ORANGE WHITE ORANGE GREEN WHITE GREEN
++ -
TX
Module connection
Maximum power available for the modules depending on the type of power supply.
Power supply Maximum power available [W]
Standard PoE 5
PoE from 1440 5
1595 7.5
1596B 15
Outdoor entrance panel module consumption table
Code Absorption W
UT9200 Call button modules 0.5
UT9240 Information module 0.5
UT9240M Metal information module 0.5
UT9279M Number keypad module 4.5 With 2 bistable relays active at the same
time
UT9310M Magnetic induction module 9.4 Always requires additional power supply
unit
UT9270 Touchscreen module 5.5
power supply from floor distribution unit Art. 1440 or
from standard PoE
A B power supply with additional power supply unit Art.
1595 or Art. 1596B

19
UP
UP
UP
BLACK
RED
MAX 10
UT8010
UT9200
ORANGE
BLUE & WHITE BLUE
BROWN & WHITE BROWN
WHITE ORANGE
GREEN
WHITE GREEN
++
-
+
-
TX
1440
L N
-
+
V V
1441
OUT
43
OUTOUT
21
IN
21
IN
+
-
OUT
GND
SE- SE+
NO NC
C
O
M
R
T
E
+
-
+
VV
- - -
TX TX
+
RX RX
+
ORANGE
BLUE & WHITE BLUE
BROWN & WHITE BROWN
WHITE ORANGE
GREEN
WHITE GREEN
++
-
+
-
TX
1440
L N
-
+
V V
1441
OUT
43
OUTOUT
21
IN
21
IN
+
-
OUT
GND
SE- SE+
NO NC
C
O
M
R
T
E
+
-
+
VV
- - -
TX TX
+
RX RX
+
UT9270
UT8010
Connection of button modules Art. UT9200
Connection of Touchscreen module Art. UT9270
Max 20 m. Local door-opener button.
Max 10 modules (Max 30 modules with additional power supply, see “Connection with separate power supply”).
Max 20 m. Local door-opener button.

20
1440
++
--
120-240 V
1596B
NC
C
O
M
+
-
+
VV
- - -
TX TX
+
RX RX
+
N L
UT9270 UT9270
14411441
L N
-
+
V V
ORANGE
WHITE ORANGE
GREEN
WHITE GREEN
++
-
TX
1440
OUT
43
OUTOUT
21
IN
21
IN
+
-
OUT
-
+
120-230 V
1595
GND
SE- SE+
NO NC
C
O
M
R
T
E
+
-
+
VV
- - -
TX TX
+
RX RX
+
UT8010 UT8010
ORANGE
BLUE & WHITE BLUE
BROWN & WHITE BROWN
WHITE ORANGE
GREEN
WHITE GREEN
++
-
+
-
TX
1440
L N
-
+
V V
1441
OUT
43
OUTOUT
21
IN
21
IN
+
-
OUT
GND
SE- SE+
NO NC
C
O
M
R
T
E
+
-
+
VV
- - -
TX TX
+
RX RX
+
UT9279M
UT8010
Connection of Touchscreen module Art. UT9270 with additional power supply unit
Connection of number keypad module Art. UT9279M
Max 20 m. Local door-opener button.
Max 20 m. Local door-opener button.