CommScope FD21206-48SRC Series Instruction sheet

www.commscope.com Bulletin # 7843672 Rev. B
Technical Publication
1
Related Support and Learning Opportunities Offered by the CommScope Infrastructure Academy
The insights and expertise contained in this manual represent just one small part of CommScope's
global learning initiative. Few industries are evolving as quickly as wireless communications. Every
technological innovation impacts what happens in the field. Our customers look to the CommScope
Infrastructure Academy to make sure their technicians and installers are well trained, well-prepared,
and well-educated to take advantage of opportunities as they evolve. To access a course, go to
www.commscopetraining.com/coursecatalog.php, course #6107
Section 1: HELIAX®Pendant Connect / Accessories ………………................................………………….…02
Section 2: General Specifications: Trunk .……………………………………………………………………….…03
Section 3: Hoisting Considerations .........................................…………………………………………..………04
Section 4: Mounting ………….......................………………....………………………………………………….…07
Section 5: General Specifications: Junpers .....................…………………….…………………………….....08
Section 6: HQLC Installation .....................................................…………………………………………..………11
Section 8: Fiber Mapping ...........................................................................…………………………..……...…12
Section 9: FE-16148-OVP-B12 Junction Box Wiring Diagram ................…………………………..……...…13
Section 10: Breakout Procedure / DLC Connection Considerations ....…………………………..……...…15
Section 11: All-in-One Cleaner / Inspecting .....….......................................................…………………....…16
Section 12: Excess Cable Management .................................................………….….…….……………..……17
Section 13: Jacketing Removal Procedure for Universal Grounding ...................................………………19
Section 14: Installation Check List .....................................................……………….......................….………20
Installation Guidelines – HELIAX®12 RRU Assembly
Solution: Pendant Conguration

www.commscope.com Bulletin # 7843672 Rev. B
Technical Publication
2
Section 1: Pendant Connect
Pendant
breakout
Bottom
enclosure
Hybrid trunk
cable
Hybrid fiber and
power jumpers
RRU's
Bottom Enclosure
PART NUMBER DESCRIPTION
FE-16148-OVP-B12 Fiber and power cable connection enclosure. Weatherproof to IP67
Other
DESCRIPTION CABLE PART NUMBER
FD21206 FD21204 Hybrid Jumper Assemblies
Hoisting Grip 29961-C 29961-C N/A
Hanger SSH-XL SSH-XL SSH-M
Angle Adapter UA-3 UA-3 UA-3
3-way Standoff SA-38 SA-38 SA-38
Round member adapter, 2 to 3 inch 31670-2 31670-2 31670-2
Round member adapter, 3 to 4 inch 31670-3 31670-3 31670-3
Round member adapter, 4 to 5 inch 31670-4 31670-4 31670-4
Universal grounding kit UG12158-15B4-T UG12158-15B4-T UG12158-15B4-T
Accessories
Equipment
cabinet / shelter
Discrete
jumpers

www.commscope.com Bulletin # 7843672 Rev. B
Technical Publication
3
FD21206-48SRC-XXX
6 AWG (up to 225 ft)
12
48
G.657.A2/B2
2544.0 kg/km| 1710.0 lb/kft
39.38 mm | 1.55 in
775 mm | 31 in
826 mm | 33 in
610 mm | 24 in
472.44 mm | 18.6 in
HQLC connectors
(Senko IP25 Plug)
DLC
connectors
Cable
Assembly
Length
Power
conductors
End 1 RRU
End 2 BBU
Section 2: General Specifications
Cable Type
Center Conductor Gauge
Conductors, quantity
Total Fiber Quantity
Fiber Type
Specifications
Cable Weight
Diameter Over Jacket
Breakout Length, Fiber, end 2
Breakout Length, Power, end 2
Minimum Bend Radius
DLC connectors
with power pins
FD21204-48SRC-XXX
4 AWG (250 - 450 ft)
12
48
G.657.A2/B2
3,576 kg/km | 2403 lb/kft
44.70 mm | 1.76 in
775 mm | 31 in
826 mm | 33 in
610 mm | 24 in
360.7 mm | 14.2 in
PART NUMBER DESCRIPTION
FD21206-48SRC-XXX
FD21204-48SRC-XXX
6AWG or 4AWG 12 RRU Hybrid Trunk Cables
End 1: Pendant breakout enclosure with 12 HQLC Senko IP25 Plug connection interface.
End 2: 12-6 WG or 12-4AWG DC conductors blunt-cut, 48 single mode bers (24 pairs) terminated
DLC

www.commscope.com Bulletin # 7843672 Rev. B
Technical Publication
4
Section 3: Hoisting Considerations
• In general this cable will handle similarly to coaxial cable, and similar installation techniques apply. All cables
are individually serialized, be sure to write down the cable serial number for future reference.
• Be sure that the Pendant is not damaged by attachment of a hoisting grip or during the hoisting process.
• During hoisting ensure that there is a free path and that the cable.
• Installation temperature range is -30 °C to +70 °C (-22 °F to +158 °F).
• Maximum cable tensile load can be found on-line in our eCatalog section at www.commscope.com.
• CommScope Lace-Up Hoisting Grip 29961-C for FD21206 and FD21204 installation.
• Hoisting Grip should be anchored to the support structure after the hangers are installed.
Hybrid Fiber Cables weigh more than traditional coaxial cables. Be sure to follow proper hoisting and
attachment procedures.
!
Keep protected
during hoisting.
* Be sure that the weight is on the
hoisting grip(s) and not the Pendant
Use a Tie back rope at the base of the
Pendant to secure to the hoisting line
Keep 304 mm (1 ft)
of cable below the
Pendant straight during
hoisting and routing.

www.commscope.com Bulletin # 7843672 Rev. B
Technical Publication
5
Required
Apply provided Tie
Wrap to the base of
the hoisting grip before
applying tension to
the line.
!
Clevis
Steel cable
or rope
hoist line
Hoisting
grip
Minimum
leader
5.3 m
(17 ft)
Maximum 60 m (200 ft)
between hoisting grips
Hoisting Considerations
Tie back ropes
1 m (3 ft)
* If the structure does not allow the
Pendant to fit through access ports due
to space limitations skip to page #6

www.commscope.com Bulletin # 7843672 Rev. B
Technical Publication
6
Clevis
Steel cable
or rope
hoist line
Hoisting
grip
Minimum
leader
5.3 m
(17 ft)
Maximum 60 m (200 ft)
between hoisting grips
Hoist line
pulley
Hybrid
cable
Rope
tie
Rope
safety line
Hoist line
inside of
monopole
Hoisting
grip
Tag
line
Hoist line
Cable
bridge
WARNING
Protect Hybrid cable
from external damage
Required:
Apply Tie
Wrap to the
base of the hoisting
grip to avoid
slipping of the grip.
Brennan
Tower Dogs
BBU End
NOTE:
If congestion inside of the pole
doesn't allow for hoisting the
pendant from the bottom port
remove old and unused coax
to free up space or consider
banding the cable to the outside
of the pole.
Cable can be rigged to pull the
smaller diameter BBU end from
the top port down. Cable will
need to be completely uncoiled
from the reel to access the BBU
end.
Protective
corrugated
sleeve
Hoisting Considerations

www.commscope.com Bulletin # 7843672 Rev. B
Technical Publication
7
Section 4: Mounting
Pendant allows mounting on poles, H-frames, walls, and other common
structures on towers, buildings, etc. Contractor provides appropriate hardware.
Requires
2 mounts
!
Bottom Mount Bracket
Top Mount Bracket

www.commscope.com Bulletin # 7843672 Rev. B
Technical Publication
8
Section 5: General Specifications Jumpers
• The terminated fiber ends however are fragile and must be protected during installation. Leave the packaging
around the fiber ends in place until ready to make final connection of the jumper at the RRU or BBU.
• DO NOT BEND THE FIBER ENDS TIGHTER THAN 30 mm (1.2 in) BEND RADIUS ELSE THERE IS A RISK OF BREAKING THE
GLASS FIBERS.
• Attach the main cable securely to the structure or equipment using mount to prevent strain on connections from
movement in wind or snow/ice conditions.
• HQLC outdoor connector is a 1/4 turn, tighten until the shell hits a positive stop.
• Installation temperature range is -30 °C to 70 °C (-22 °F to 158 °F).
• Red conductor is -48V and Black is the Return.
Cable Type
Total Fiber Quantity
Conductor AWG | quantity
Fiber Type
Specifications
Cable Weight
Breakout Length Fiber, end 1
Breakout Length Power, end 1
Breakout Length Fiber, end 2
Breakout Length Power, end 2
Diameter Over Jacket
Minimum Bend Radius
HFT410-4SNOK2-xx
4
10 | 4
G.657.A2
456.1 kg/km | 306.5 lb/kft
815 mm | 32 in
895 mm | 35 in
609 mm | 24 in
609 mm | 24 in
18.31 mm | 0.72 in
221.0 mm | 8.7 in
General Specifications
HFT410-4SNOK4-xx
4
10 | 4
G.657.A2
456.1 kg/km | 306.5 lb/kft
750 mm | 29.5 in
775 mm | 30.5 in
609 mm | 24 in
609 mm | 24 in
18.31 mm | 0.72 in
221.0 mm | 8.7 in
HFT410-4SNOK5-xx
4
10 | 4
G.657.A2
456.1 kg/km | 306.5 lb/kft
815 mm | 32 in
457 mm | 18 in
609 mm | 24 in
609 mm | 24 in
18.31 mm | 0.72 in
221.0 mm | 8.7 in
Cable Type
Total Fiber Quantity
Conductor AWG | quantity
Fiber Type
Specifications
Cable Weight
Breakout Length Fiber, end 1
Breakout Length Power, end 1
Breakout Length Fiber, end 2
Breakout Length Power, end 2
Diameter Over Jacket
Minimum Bend Radius
HFT206-4SNOK6-xx
4
6 | 2
G.657.A2
456.1 kg/km | 306.5 lb/kft
787 mm | 31 in
762 mm | 30 in
609 mm | 24 in
609 mm | 24 in
18.31 mm | 0.72 in
221.0 mm | 8.7 in
General Specifications (cont.)
HFT206-6SB41-xx
6
6 | 2
G.657.A2 /B2
726.2 kg/km | 488 lb/kft
864 mm | 34 in
800 mm | 31.5 in
609 mm | 24 in
609 mm | 24 in
24.4 mm | 0.96 in
292.1 mm | 11.5 in
HFT206-8SB41-xx
8
6 | 2
G.657.A2/B2
726.2 kg/km | 488 lb/kft
864 mm | 34 in
800 mm | 31.5 in
609 mm | 24 in
609 mm | 24 in
25.8 mm | 1.0 in
309.8 mm | 12.2 in
Cable Type
Total Fiber Quantity
Fiber Type
Specifications
Cable Weight
Breakout Length Fiber, end 1
Breakout Length Fiber, end 2
Diameter Over Jacket
Minimum Bend Radius
DFJ-6S010-xx | DFJ-12S010-xx
6 or 12
G.657.A2
69 kg/km | 46 lb/kft
762 mm | 30 in
1067 mm | 42 in
8 mm | 0.31 in
8.0 cm | 3.1 in
General Specifications (cont.)
DFJ-6S025-xx | DFJ-12S025-xx
6 or 12
G.657.A2
69 kg/km | 46 lb/kft
762 mm | 30 in
1067 mm | 42 in
8 mm | 0.31 in
8.0 cm | 3.1 in

www.commscope.com Bulletin # 7843672 Rev. B
Technical Publication
9
PART NUMBER DESCRIPTION
HFT410-4SNOK2-xxx
Hybrid Jumpers for Nokia RRU (FHFB, FRIJ, FRIG, FXFC, FRIA, FRIB, FRIE pre-v202 and FASB integrated
antenna)
End 1: 4 bers terminated DLC with weatherproong boot for Nokia RRUs with ush cut power cord
(red/black conductors)
End 2: 4 bers terminated LC and 4-10AWG conductors terminated at HQLC (Senko IP25 Plug)
End 1 RRU End 2 Pendant/Enclosure
PART NUMBER DESCRIPTION
HFT410-4SNOK4-xxx
Hybrid Jumpers for Nokia RRU (AirScale ALHOA, AAFIA, AHFIB)
End 1: 4 bers terminated DLC with R2CT weatherproong shroud for Nokia AirScale radio with power
connector
End 2: 4 bers terminated LC and 4-10AWG conductors terminated at HQLC (Senko IP25 Plug)
End 1 RRU End 2 Pendant/Enclosure
PART NUMBER DESCRIPTION
HFT410-4SNOK5-xxx
Hybrid Jumpers for Nokia Legacy RRU (FXFB, FRIE-v202) with Power Connector
End 1: 4 bers terminated DLC with weatherproong boot for Nokia RRUs with power connector
End 2: 4 bers terminated LC and 4-10AWG conductors terminated at HQLC (Senko IP25 Plug)
End 1 RRU End 2 Pendant/Enclosure
PART NUMBER DESCRIPTION
HFT206-4SNOK6-xxx
Hybrid Jumpers for Nokia RRU (AirScale AHFIG)
End 1: 4 bers terminated DLC with weatherproong boot for Nokia AirScale radio with R2CT weather
shields and blunt-cut power leads
End 2: 4 bers terminated LC and 2-6AWG conductors terminated at HQLC (Senko IP25 Plug)
End 1 RRU End 2 Pendant/Enclosure

www.commscope.com Bulletin # 7843672 Rev. B
Technical Publication
10
PART NUMBER DESCRIPTION
HFT206-6SB41-xxx
Hybrid Jumpers for Nokia RRU (AirScale AAHF)
End 1: 6 bers terminated in 3 pairs DLC with Octis weatherproong shroud. 55A DC power
connector on 2-6AWG conductors.
End 2: 6 bers terminated in dual HQLC (Senko IP25) connectors, 4 bers and 2-6AWG conductors in
connector #1, 2 bers in connector #2.
End 1 RRU End 2 Pendant/Enclosure
PART NUMBER DESCRIPTION
HFT206-8SB41-xxx
Hybrid Jumpers for Nokia RRU (AirScale AEHC)
End 1: 8 bers terminated in 4 pairs DLC with Octis weatherproong shroud. 70A DC power
connector on 2-6AWG conductors.
End 2: 8 bers terminated in dual HQLC (Senko IP25) connectors, 4 bers and 2-6AWG conductors in
connector #1, 4 bers in connector #2.
End 1 RRU End 2 Pendant/Enclosure
PART NUMBER DESCRIPTION
DFJ-6S010-xxx
DFJ-12S010-xxx
(shown)
Discrete Fiber Jumpers with weatherproong boot for Nokia Radios, 6 or 12 single mode bers,
armored
End 1: DLC breakout with weatherproong boot
End 2: DLC breakout to enclosure
End 1 BBU End 2 Pendant/Enclosure
PART NUMBER DESCRIPTION
DFJ-6S025-xxx
DFJ-12S025-xxx
(shown)
Discrete Fiber Jumpers for Nokia AirScale Radios, 6 or 12 single mode bers, armored
End 1: DLC breakout for Nokia systems module
End 2: DLC breakout to enclosure
End 1 BBU End 2 Pendant/Enclosure

www.commscope.com Bulletin # 7843672 Rev. B
Technical Publication
11
Section 6: HQLC Installation
1
2
3
Remove dust cap from pendant assembly by pulling back on red
safety lock-ring. Rotate connector collar nut counter-clockwise
and pull back. Remove Qty. 4 white ferrule dust caps. DO NOT
remove caps from ports not being used.
Warning: DO NOT touch or place anything into power pins when
site is powered up.
Remove dust cap from jumper assembly by pulling back on red
Safety lock-ring. Rotate connector collar nut counter-clockwise
and pull back. Pull forward on the dust cap. Remove Qty. 4 white
ferrule dust caps.
Locate the alignment keys on the HQLC connector and the
pendant. Insert the connector straight into the port making sure
the keys are aligned correctly. Push until front seal is fully under
adapter housing.
Engage the collar nut at pendant and twist clockwise ¼ turn until it stops and “click” is heard or felt. Slide
the red safety lock-ring up and under the collar nut. Install a 20cm x 4.5mm UV rated cable tie for additional
security. Collar nut should not be able to rotate once installed. Support jumper within 152 mm (6 in) from the
back of the connector. Verify the unused caps are tight before leaving the site as they provide the weather
seal for the connector.
152 mm
(6 in)
Be careful during nal routing
to avoid placing unwanted
stress on the assembly
Warning: The female end of the connector attached to
the pendant are not eld removable. Do Not attempt
to remove with wrench.
+ -
+ -
UV rated cable tie for
additional security
Alignment
keys
Power
sockets
Fibers
Collar
Nut
Dust
Cap
Lock
Ring
Collar
Nut
Lock
Ring

www.commscope.com Bulletin # 7843672 Rev. B
Technical Publication
12
Section 8: Fiber/Power Mapping
Radio 0 Radio 1 Radio 2 Radio 3
Optical 1 Optical 2 Optical 1 Optical 2 Optical 1 Optical 2 Optical 1 Optical 2
17181920 2 1 2 223 2 4 Gamma
0 9 1 0 111 2 1 3 1 41516 Beta
0 1 0 2 0 3 0 4 0 5 0 6 0 7 0 8 Alpha
Bottom Junction Box
Power Pin's:
Pins on the left are RED when facing the connector.
Pins on the right are BLACK when facing the connector
BBU ends are labeled per sector
Alignment
keys
Power
sockets
Fibers
12 8 4
11 7 3
10 6 2
9 5 1
2 4
2 3
1 6
1 5
0 8
07
0 5
0 6
13
41
21
22
1 9
20
1
1 2
1
0 4
0 3
17
811 0
0 9
0 2
0 1
C2
C1
C0
C3
B2
B1
B0
B3
A2
A1
A0
A3

www.commscope.com Bulletin # 7843672 Rev. B
Technical Publication
13
Power Conductors
Jumper Fiber Connections
Section 9: FE-16148-OVP-B12 Junction Box Wiring Diagram
Seal the ber box lid with provided E20 Torx screw with E4 security
pin head (Qty 4) to the torque value range: 11.52 +1/-0 Kgf.cm
Dome Nut Torque value range: 6 +/-.5 Nm (53 +/- 4 in lbs)
Terminal Blocks:
Torque value range:
1.5 – 1.8 Nm
(13.3 – 15.9 in lbs)
OVP
Hybrid Trunk
Trunk Fiber Connections
Trunk Power Connections
Grounding to the integral OVP is
mandatory. A 2 to 6 AWG weather-
able conductor should be run as
straight and short as possible to an
adequate grounding point to per-
form properly. (contractor supplied)
Ground / AlarmGround / Alarm
WireWire
Alarm wire isAlarm wire is
connected toconnected to
the green alarmthe green alarm
terminalterminal
Power cords are labeled per sector
The power labels can be lost if the length is significantly reduced during
installation. Always re-label conductors before cutting off excess.
Jumper Fiber Connections
OVP window will be green on
the initial position, the window
will be red after a surge trips

www.commscope.com Bulletin # 7843672 Rev. B
Technical Publication
14
Ground
Wire
Alarm
Wire
Fiber
Tails
Power
Hybrid
Trunk
1 7 1 8 1 9 2 0 2 1 2 2 2 3 2 4
0 9 1 0 1 1 1 2 1 3 1 4 1 5 1 6
0 1 0 2 0 3 0 4 0 5 0 6 0 7 0 8
Fiber Adapter Panel
Junction Box (bottom view)
1 1/2 in
conduit tting
12 11 14
NC C NO
Torque
.25 Nm
(416 in lbs)
Alarm Wire Terminal
7 mm
(.28 in)
Alarm wire 30 - 18 AWG supplied by
contractor
Hybrid
Trunk
Circuit Breaker Size Recommendation
Pendant Amperage
12 RRU 90A
Attached to
base plate
Side facing power
terminal blocks
Radio 0 Radio 1 Radio 2 Radio 3
Optical 1 Optical 2 Optical 1 Optical 2 Optical 1 Optical 2 Optical 1 Optical 2
17 1 8 1 9 2 0 2 1 2 2 2 3 2 4 Gamma
0 9 1 0 1 1 1 2 1 3 1 4 1 5 1 6 Beta
0 1 0 2 0 3 0 4 0 5 0 6 0 7 0 8 Alpha

www.commscope.com Bulletin # 7843672 Rev. B
Technical Publication
15
DLC Connectors and Adapter cleaning
Clean exposed connector ferrule by lightly moistening lint-free wipe with ber optic cleaning solution (or >91% isopro-
pyl alcohol), and by applying medium pressure, rst wipe against wet area and then onto dry area to clean potential
residue from end face. Clean connector ferrule inside adapter by inserting lightly moistened cleaning stick with ber
optic cleaning solution (or >91% isopropyl alcohol) inside the adapter until contact is made with connector on opposite
end. Rotate cleaning stick with medium pressure in one circular motion as it is pulled away from the adapter. Repeat
process using dry cleaning stick.
Caution: Signal strength will be affected if end and sides of ferrule are not thoroughly cleaned. Discard cleaning
sticks after each use. Do not turn cleaning sticks back and forth pressing against connector end face. This may cause
scratches if large contamination is present. Always inspect connector end face for contamination after each cleaning.
Clean adapter by inserting adapter cleaning stick (or fiber adapter sleeve brush) moistened with fiber optic cleaning
solution (or >91% isopropyl alcohol) inside the adapter and gently pull out with twisting motion. Repeat process with a
dry cleaning stick.
Caution: Do not try to clean adapter with a standard pipe cleaner. The sleeve inner diameter of DLC adapters is too
small. Do not try to clean the adapter with cleaning stick if a connector is mounted in one side. Discard cleaning sticks
after each use.
Clean Tip of Ferrule
Clean Sides of Ferrule
Adapter Brush
Section 10: Breakout Procedure
Remove electrical tape
from the trunk cable and
corrugated protection
tube
While holding the protection tube straight
pull the tube away from cable.
After you have pulled the ber and power
conductors into the OVP box remove electrical
tape from the trunk cable and remove clear tube
for access to all optical connectors.
After the trunk cable has been installed and
you are ready to make the nal connection
to the BBU follow these steps for the removal
of ber protection tube.
1
2
3

www.commscope.com Bulletin # 7843672 Rev. B
Technical Publication
16
Device designed for cleaning the ferrule end faces of LC connectors
Open guide cap, insert LC connector into guide, push the outer shell to start cleaning the LC connector interface, a
"click" sound indicates end of a cleaning process, repeat, close cap immediately after use.
Caution: Be careful not to slant LC connector while inserting into the Guide cap. Do not overly exert force during
insertion as this may cause damage to both the connector and the cleaner.
Section 11: All in one cleaner
Guide
LC Connector
Push Cleaner X2
Cap
Part Number: FCCT - L
There are 3 basic principles that are critical to achieving an efficient fiber optic connection:
1. Perfect Core Alignment
2. Physical Contact
3. Pristine Connector Interface
Today’s connector design and production techniques have eliminated most of the challenges to achieving
core alignment and physical contact. What remains challenging is maintaining a pristine end-face. As a result,
CONTAMINATION is the #1 reason for troubleshooting optical networks.
Implementing the process of cleaning and inspecting before mating can reduce the time spent troubleshooting,
optimize signal performance and prevent damage.
Inspecting
Is It
Clean?
No Connect
Yes
Inspect
Clean
Clean
Abrasive particles (i.e. rock dust) can
cause permanent damage to the
interface. If interface is scratched it cannot
be repaired, it would need to be replaced.
!
Scan to
view video

www.commscope.com Bulletin # 7843672 Rev. B
Technical Publication
17
Section 12: Excess Cable Management
If length of cable installed needs to be adjusted you can split the cable at the BBU end using the process below and
then coiling the excess fiber subunits in a storage box. Patch Panel Kits are available to manage any excess fiber
length in the breakouts at the BBU.
Mark cutback length Notch Armor using flush cutter in-line with
Kevlar strings
Place Rip Cord in Notches' Pull Rip Cord Parallel to Cable
(while supporting breakout)
Stop at Length Marker Separate Armor
1 2
34
56
Scan to
view video

www.commscope.com Bulletin # 7843672 Rev. B
Technical Publication
18
Excess Cable Management (continued)
Cut Armor Using Side Cutter Remove Water Blocking Tape
Remove Excess Rip Cord Apply Electrical Tape to Protect Breakout
NOTE:
Remember to slide
identifier labels
down the power
conductors before
trimming the cable
to it’s final length
Cable Splitter tool
Part Number:
FA-RCRT-PD
Seam Ripper
NOTE:
Step can be
expedited by using
a sewing seam
ripper that can be
purchased at local
hobby stores
7 8
910

www.commscope.com Bulletin # 7843672 Rev. B
Technical Publication
19
Earthing Kit UG12158-15B4-T is a universal
solution for all trunk cables
Note: Only use Tin Plated earthing kits
Section 13: Jacketing Removal Procedure for Universal Grounding Kit
1. Score the jacketing 360º
2. Measure 51 mm (2 in) and repeat
3. Identify where the aluminum shielding overlaps, this will feel like a flat spot in the cable
4. With a knife flat on the cable remove a section of jacketing between score marks
5. Lift edge of jacketing with knife tip
6. Grab lifted edge of jacketing with a pair of pliers and roll on the cable
7. Remove excess adhesive with a piece of emery cloth
Scan to
view video

www.commscope.com Bulletin # 7843672 Rev. B
Technical Publication
20
Tails are properly support to prevent strain on fiber during severe weather
Bend radius minimums haven't been exceeded
CommScope approved installation accessories are used
Maximum hanger spacing of 0.9 m (3 ft) - 1.2 m (4 ft) is maintained
Visually inspected end face for residual dirt and damage
Avoid migration of contaminations from one connector to another
Check continuity by using LED or laser light source from one end face and look for light from other end to
identify any broken fiber (Do not look directly at cable with laser source)
Fiber Connections are engaged and the sectors are consistent with requirements
Verify dust caps on any unused Pendant interfaces have not come loose. Retighten if required.
Cable serial number has been documented in the closeout paperwork and a copy has been left on-site
Section 14: Installation Check List
© 2020 CommScope
Notice: CommScope disclaims any liability or responsibility for the results of improper or unsafe installation, inspection, maintenance, or removal practices.
Aviso: CommScope no acepta ninguna obligación ni responsabilidad como resultado de prácticas incorrectas o peligrosas de instalación, inspección, mantenimiento o retiro.
Avis : CommScope décline toute responsabilité pour les conséquences de procédures d’installation, d’inspection, d’entretien ou de retrait incorrectes ou dangereuses.
Hinweis: CommScope lehnt jede Haftung oder Verantwortung für Schäden ab, die aufgrund unsachgemäßer Installation, Überprüfung, Wartung oder Demontage auftreten.
Atenção: A CommScope abdica do direito de toda responsabilidade pelos resultados de práticas inadequadas e sem segurança de instalação, inspeção, manutenção ou remoção.
Avvertenza: CommScope declina eventuali responsabilità derivanti dell’esecuzione di procedure di installazione, ispezione, manutenzione e smontaggio improprie o poco sicure.
CommScope
1100 CommScope Place SE P.O. Box 339, Hickory, NC 28603-0339
[phone] [phone]
www.commscope.com
Technical Support
[phone], Option 3 (Toll Free US and Canada)
[phone], Option 3 (local)
https://www.commscope.com/wisupport (open a ticket)