CommScope Propel PPL-1U-HD-FX User manual

TC-96342-IP
Rev B, August 2023
commscope.com
User
Manual
Propel™ Fixed and Fixed Open Panels
Electronic Only Document (EOD)
© 2023 CommScope, Inc.
Propel Fixed and Fixed Open Panel
2RU Shown (Left), 2RU-OPEN Shown (Right)
1 INTRODUCTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.1 Propel Fixed Panel Configurations Covered by This User Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.2 Available Connection Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.3 Important Safety Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.4 Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.5 Related Publications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2 PRODUCT DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.1 General Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.2 Main Product Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.3 Specifications and Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.4 Blades . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.5 QR Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.5.1 Product QR Codes on Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
2.5.2 Component QR Codes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3 UNPACKING AND INSPECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
4 OVERVIEW OF INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
5 INSTALLING THE PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
5.1 Determining Rack Size and Mounting Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
5.2 Installing Kits for Alternative Rack Sizes (Not 19-Inch) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
5.2.1 23-Inch Rack (584mm) Mount Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
5.2.2 ETSI Rack Mount Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
5.3 Panel Recess Options, Fixed Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
5.3.1 Mounting Bracket Position on Panel as Shipped . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
5.3.2 Mounting Bracket in 3.5-Inch Offset Position (Front of Rack Mounting) . . . . . . . . . . . . . . . . . . . . . 20
5.3.3 Mounting Bracket in 6-Inch Offset Position (Front of Rack Mounting) . . . . . . . . . . . . . . . . . . . . . . 20
Continued
Content Page
28033-A

TC-96342-IP
Page 2
© 2023 CommScope. All Rights Reserved.
5.3.4 Mounting Bracket in 9-Inch Offset Position (Rear of Rack Mounting) . . . . . . . . . . . . . . . . . . . . . . . 21
5.4 Panel Recess Options, Fixed Open Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
5.4.1 Mounting Bracket Position on Panel as Shipped . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
5.4.2 Mounting Bracket in 3.5-Inch Offset Position (Front of Rack Mounting) . . . . . . . . . . . . . . . . . . . . . 22
5.4.3 Mounting Bracket in 6-Inch Offset Position (Front of Rack Mounting) . . . . . . . . . . . . . . . . . . . . . . . 22
5.4.4 Mounting Bracket in 9-Inch Offset Position (Rear of Rack Mounting) . . . . . . . . . . . . . . . . . . . . . . . 23
5.5 Mounting the Panel on the Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
5.6 Installing Connection Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
5.7 Installing Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
5.7.1 Installing Cables in a Propel Fixed Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
5.7.2 Installing Cables in a Propel Fixed Open Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
5.8 Installing Patch Cords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
6 OPERATIONAL DETAILS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
6.1 Front Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
6.1.1 Opening the Front Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
6.1.2 Closing the Front Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
6.2 Rear Cover (Propel Fixed Panel) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
6.2.1 Removing the Rear Cover on the 1RU and 2RU Panel (Propel Fixed Panel) . . . . . . . . . . . . . . . . . . 31
6.2.2 Re-installing the Rear Cover on the 1RU and 2RU Panel (Propel Fixed Panel) . . . . . . . . . . . . . . . . 31
6.2.3 Opening the Rear Cover on the 4RU Panel (Propel Fixed Panel) . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
6.2.4 Closing the Rear Cover on the 4RU panel (Propel Fixed Panel) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
6.3 Connection Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
6.3.1 Placement of Connection Components on a Blade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
6.3.2 Installing a Connection Component . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
6.3.3 Removing a Connection Component . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
6.4 Cables and Rear Cable Management Clips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
6.4.1 Installing a Cable on a Propel Fixed Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
6.4.2 Installing a Cable on a Propel Fixed Open Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
6.4.3 Routing Cables from the Panel on the Frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
6.5 Patch Cords. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
7 CONTACT INFORMATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Content Page

TC-96342-IP
Page 3
© 2023 CommScope. All Rights Reserved.
1 INTRODUCTION
The CommScope Propel Fixed Panel, available in the configurations listed in Table 1, is a modular
fiber connection platform that allows Propel modules, splice cassettes, and adapter packs of
different sizes to be installed in any position in the panel where space is available.
This user manual describes the Propel Fixed Panel and tells how to unpack the panel, mount it on a
rack, and install connection components including Propel modules, splice cassettes, and adapter
packs. In addition, this manual tells how to route and secure cables and patch cords, and how to
obtain technical assistance if needed.
1.1 Propel Fixed Panel Configurations Covered by This User Manual
Table 1 lists the Propel Fixed Panel configurations covered in this user manual.
1.2 Available Connection Components
For a listing of the available Propel connection components, including MPO modules and adapter
packs, see Table 2. Splice cassettes are not available at this time.
Table 1. Propel Fixed Panel Configurations
Material ID (MID) Catalog # Density
760253796 PPL-1U-HD-FX 48 duplex LC, 48 MPO, 192 SN
760253797 PPL-2U-HD-FX 96 duplex LC, 96 MPO, 384 SN
760253798 PPL-4U-HD-FX 192 duplex LC, 192 MPO, 768 SN
760254865 PPL-1U-HD-FX-OPEN 48 duplex LC, 48 MPO, 192 SN
760254908 PPL-2U-HD-FX-OPEN 96 duplex LC, 96 MPO, 384 SN
Table 2. Available MPO Modules and Adapter Packs
Modules & Adapter Packs Material ID (MID) Catalog Number Fiber Type Fiber Count
MPO8 Modules with MPO/UPC
12 per 1RU
760252332 PPL-DM-8U-8LC-OM4-BEU OM4 8
760252333 PPL-DM-8U-8LC-OM5-BEU OM5 8
760252334 PPL-DM-8AU-8LC-SM-BEU OS2 8
4 per 1RU
760252337 PPL-DM-8U-24LC-OM4-BEU OM4 24
760252338 PPL-DM-8U-24LC-OM5-BEU OM5 24
760252339 PPL-DM-8AU-24LC-SM-BEU OS2 24
MPO8 Modules with MPO/APC in multimode
12 per 1RU 760252335 PPL-DM-8AU-8LC-OM4-BEU OM4 8
760252336 PPL-DM-8AU-8LC-OM5-BEU OM5 8
8-fiber Adapter Packs

TC-96342-IP
Page 4
© 2023 CommScope. All Rights Reserved.
12 per 1RU
760252359 PPL-AP-8-LC-SM OS2 8
760252360 PPL-AP-8-LC-OM4 OM5 8
760252361 PPL-AP-8-LC-OM5 OS2 8
760252371 PPL-AP-4-MPO-ALL-B All 32
MPO12 Modules
8 per 1RU
760252343 PPL-DM-12U-12LC-OM4-BEU OM4 12
760252344 PPL-DM-12U-12LC-OM5-BEU OM5 12
760252345 PPL-DM-12AU-12LC-SM-BEU OS2 12
4 per 1RU
760252346 PPL-DM-12U-24LC-OM4-BEU OM4 24
760252347 PPL-DM-12U-24LC-OM5-BEU OM5 24
760252348 PPL-DM-12AU-24LC-SM-BEU OS2 24
12-fiber Adapter Packs
8 per 1RU
760252362 PPL-AP-12-LC-SM OS2 12
760252363 PPL-AP-12-LC-OM4 OM4 12
760252364 PPL-AP-12-LC-OM5 OM5 12
760252372 PPL-AP-6-MPO-ALL-B All 72
MPO16 Modules
6 per 1RU
760252352 PPL-DM-16AU-16LC-SM-BEU OS2 16
760252353 PPL-DM-16AU-16LC-OM4-BEU OM4 16
760252354 PPL-DM-16AU-16LC-OM5-BEU OM5 16
16-fiber Adapter Packs
6 per 1RU
760252365 PPL-AP-16-LC-SM OS2 16
760252366 PPL-AP-16-LC-OM4 OM4 16
760252367 PPL-AP-16-LC-OM5 OM5 16
760252804 PPL-AP-8-MPO16-ALL-B All 128
12 per 1RU 760252806 PPL-AP-4-MPO16-ALL-B All 64
8 per 1RU 760252805 PPL-AP-6-MPO16-ALL-B All 96
4 per 1RU 760252803 PPL-AP-12-MPO16-ALL-B All 96
MPO24 Modules
4 per 1RU 760252356 PPL-DM-24U-24LC-OM4-BEU OM4 24
760252357 PPL-DM-24U-24LC-OM5-BEU OM5 24
24-fiber Adapter Packs
4 per 1RU
760252368 PPL-AP-24-LC-SM OS2 24
760252369 PPL-AP-24-LC-OM4 OM4 24
760252370 PPL-AP-24-LC-OM5 OM5 24
760252374 PPL-AP-12-MPO-ALL-B All 288
Table 2. Available MPO Modules and Adapter Packs, continued
Modules & Adapter Packs Material ID (MID) Catalog Number Fiber Type Fiber Count

TC-96342-IP
Page 5
© 2023 CommScope. All Rights Reserved.
1.3 Important Safety Cautions
When installing or operating the panel, observe these safety cautions:
• To reduce the risk of fire, electric shock, and injury to persons, read, understand, and adhere
to the following instructions as well as any warnings marked on the product.
• This product has a remote risk of electric shock. Never install the product in wet conditions or
during lightning storms. Never touch uninsulated communication wires or terminals.
• Wearing safety glasses during installation of this panel is recommended. Although standard
safety glasses provide no protection from potential optical radiation, they offer protection from
accidental airborne hardware and cleaning solvents.
• Disconnected optical components may emit invisible optical radiation that can damage your
eyes. Never look directly into an optical component that may have a laser coupled to it.
Serious and permanent retinal damage is possible. If accidental exposure to laser radiation is
suspected, consult a physician for an eye examination.
1.4 Precautions
When installing or operating the panel, observe the following precautions:
• Fiber optic trunk cable and jumper performance is sensitive to bending, pulling, and crushing.
Minimum bend radius must be maintained during installation per the manufacturer’s
specification. Appropriate pulling grips must be used during installation, and pulling forces
shall not exceed manufacturer’s recommendations.
• All wiring that connects to this equipment must meet applicable local and national building
codes and network wiring standards for communication cable.
•IMPORTANT: Dust covers are installed in the ports to protect the fibers connected to the back
of the ports. Do not remove a dust cover from a port until you connect a patch cord to that port.
If you remove a patch cord later, replace the dust cover in the port.
•Prior to installation, clean the trunk cable and jumper connectors per the manufacturer’s
recommendations.
S/N Modules
12 per 1RU 760252342 PPL-DM-8AU-8SN-SM-BEU OS2 16
8 per 1RU 760252349 PPL-DM-12AU-12SN-SM-BEU OS2 24
12 per 1RU 760252355 PPL-DM-16AU-8SN-SM-BEU OS2 16
S/N Adapter Packs
12 per 1RU 760252375 PPL-AP-8-SN-SM OS2 16
8 per 1RU 760252376 PPL-AP-12-SN-SM OS2 24
6 per 1RU 760252377 PPL-AP-16-SN-SM OS2 32
4 per 1RU 760252378 PPL-AP-24-SN-SM OS2 48
Table 2. Available MPO Modules and Adapter Packs, continued
Modules & Adapter Packs Material ID (MID) Catalog Number Fiber Type Fiber Count

TC-96342-IP
Page 6
© 2023 CommScope. All Rights Reserved.
• Isopropyl alcohol is flammable, and can cause eye irritation on contact. If eye contact occurs,
flush with water for at least 15 minutes. In case of ingestion, consult a physician. Use only in
well ventilated areas.
• Care should be taken not to compromise the stability of the rack by installation of this
equipment.
1.5 Related Publications
The related publications listed are available by contacting the CommScope Support Center at
https://www.commscope.com/SupportCenter
Publication Title Publication Number
Propel Fixed Panel Quick Start TC-96341-IP
Propel Fixed Open Panel Quick Start TC-96355-IP

TC-96342-IP
Page 7
© 2023 CommScope. All Rights Reserved.
2 PRODUCT DESCRIPTION
2.1 General Description
The Propel Fixed Panel is a 19-inch rack-mount fiber optic connector panel intended for indoor use.
Rack adapter kits are available that enable the panel to be mounted in a 23-inch or ETSI rack. The
standard panel is available in one, two, or four rack unit sizes (abbreviated as 1RU, 2RU, or 4RU),
while a reduced-depth, open version of the panel is available in one or two rack unit sizes (1RU or
2RU). Figure 1 shows the five Fixed panels.
The Propel Fixed Panel contains two fixed position “blades” per RU, installed in the factory. Each
blade supports multiple sizes of connection components including MPO modules, adapter packs,
and splice cassettes. Connection components are installed by positioning them in any available
location on the blade and sliding them in until they click into position.
Figure 1. Propel Fixed Panel and Propel Fixed Open Panel
Precise positioning on the blade is enforced by rails that the connection components slide onto
when installed. The rails direct the components into 12 equal-sized lanes, labeled A to L. Each lane
accommodates 4 fibers or the connector equivalent. For example, an MPO module with 4 front
duplex LC ports and a rear MPO 8 connector occupies two lanes. Propel connection components
are available in 4 sizes accommodating 8, 12, 16, or 24 fibers. The largest size component
occupies 6 lanes, which is half of the blade. The Propel Fixed Panel capacity per blade is 48 fibers
Note: The open panel is officially called “Propel Fixed Open Panel” to distinguish it from the
standard version. The term “Propel Fixed Panel” is often used to refer to the fixed and
fixed open panels collectively.
PROPEL
FIXED OPEN
PANEL 28034-
A
PROPEL
FIXED
PANEL

TC-96342-IP
Page 8
© 2023 CommScope. All Rights Reserved.
(24 duplex LC ports). Capacity per RU is 96 fibers (48 duplex LC ports). If SN connection
components are used, the fiber capacity of the panel doubles in comparison to LC, because a
single SN connector has 4 fibers, while LC has 2.
2.2 Main Product Features
Figure 2 shows a front view of a 2RU Propel Fixed Panel with front door removed. The main
features are:
•Rear Cover—can be removed providing top access to rear of the panel.
•Cable Entry Area—is the portal through which cables are routed into the rear of the panel.
•Mounting Brackets (one on each side)—provide for mounting the panel in a frame or
cabinet. The panel is shipped with 19-inch mounting brackets. Kits are available for mounting
in a 23-inch or ETSI rack or cabinet.
•Blade—supports the slide-in connection components and holds them in position.
•Integral Patch Cord Entry Managers—are used to manage patch cords.
Figure 2. Propel Fixed Panel Front View (2RU Shown)
Figure 3 shows rear views of a 2RU Propel Fixed Panel with rear cover present and removed. The
main features visible from this view include the following.
•Rear Cover—can be removed providing top access to the panel.
•Cable Entry Area—is the portal through which cables are routed into the rear of the panel.
•Cable Management Bracket—holds the rear cable management clips. Each clip holds one
cable tied to it with hook-and-loop straps.
•Cable Routing Platform—is a surface across which cables are routed from connection
components out of the panel.
REAR COVER
BLADE
CABLE
ENTRY
AREA
MOUNTING
BRACKET
INTEGRAL PATCH
CORD MANAGER
28063-A

TC-96342-IP
Page 9
© 2023 CommScope. All Rights Reserved.
Figure 3. Propel Fixed Panel (2RU Shown)
Figure 4 shows the rear of the 2RU Propel Fixed Open Panel. The main features visible from this
view include the following.
•Patch Cord Entry Area—is the portal through which cables are routed into the front of the
panel.
•Cable Management Strip—supports cables routed from connection components and
provides tie-down locations via cable management slots.
•Cable Management Slots—allow hook-and-loop straps or cable ties to secure rear cables to
cable management strip.
CABLE
ENTRY
AREA
CABLE
MANAGEMENT
BRACKET
28064-A
CABLE
ROUTING
PLATFORM
REAR COVER

TC-96342-IP
Page 10
© 2023 CommScope. All Rights Reserved.
Figure 4. Rear View of Propel Fixed Open Panel (2RU Shown)
2.3 Specifications and Dimensions
Table 3 lists dimensions for the Propel Fixed and Fixed Open Panels. Figure 5 shows dimensions
for the Propel Fixed Panels. Figure 6 shows dimensions for the Propel Fixed Open Panels.
Table 3. Propel Fixed and Fixed Open Panel Specifications
Parameter PPL-1U-HD-FX PPL-2U-HD-FX PPL-4U-HD-FX PPL-1U-HD-FX-OPEN PPL-2U-HD-FX-OPEN
Height 1.72 in
(4.36 cm)
3.47 in.
(8.81 cm)
6.97 in
(17.70 cm)
1.72 in
(4.36 cm)
3.47 in.
(8.81 cm)
Width 19.0 in.
(48.26 cm)
19.0 in.
(48.26 cm)
19.0 in.
(48.26 cm)
19.0 in.
(48.26 cm)
19.0 in.
(48.26 cm)
Depth 18.55 in. (47.11
cm)
18.55 in. (47.11
cm)
18.55 in. (47.11
cm)
11.51 in.
(29.24 cm)
11.51 in.
(29.24 cm)
Weight
(Panel Only)
8.65 lbs.
(5.92 kg)
12.15 lbs. (5.51 kg) 22.15 lbs. (10.05
kg)
6.05 lbs.
(2.74 kg)
8.80 lbs.
(3.99 kg)
Weight
(Packaged)
13.20 lbs. (5.99 kg) 17.05 lbs. (7.73 kg) 28.10 lbs. (12.75
kg.
9.20 lbs.
(4.17 kg)
12.15 lbs.
(5.51 kg)
PATCH
CORD
ENTR
Y
AREA
28065-A
CABLE
MANAGEMENT
SLOTS
CABLE
MANAGEMENT
STRIP

TC-96342-IP
Page 11
© 2023 CommScope. All Rights Reserved.
Figure 5. Propel Fixed Panel Dimensions
27504-A
18.55 IN. (47.11 CM)
17.20 IN.
(43.68 CM)
TOP VIEW
3.06 IN.
(7.77 CM)
15.11 IN.
(38.37 CM)
6.96 IN.
(17.68 CM)
3.47 IN.
(8.81 CM)
1.72 IN.
(4.36 CM)
1RU PANEL (FRONT VIEW)
2RU PANEL (FRONT VIEW)
4RU PANEL (FRONT VIEW)
1RU PANEL (SIDE VIEW)
2RU PANEL (SIDE VIEW)
4RU PANEL (SIDE VIEW)
18.31 IN. (46.51 CM)
19.00 IN. (48.25 CM)

TC-96342-IP
Page 12
© 2023 CommScope. All Rights Reserved.
Figure 6. Propel Fixed Open Panel Dimensions
2.4 Blades
Propel blades have rails that guide Propel connection components into lanes. Each blade has 12
lanes labeled A to L. Table 4 lists the available Propel Panel Fixed and Fixed Open configurations.
Table 4. Available Modules and Adapter Packs
Fixed Panel Catalog #
8-fiber modules/
adapter packs
12-fiber modules/
adapter packs
16-fiber modules/
adapter packs
24-fiber modules/
adapter packs
PPL-1U-HD-FX/
PPL-1U-HD-FX-OPEN
up to 6 per blade/
12 per panel
up to 4 per blade/
8 per panel
up to 3 per blade/
6 per panel
up to 2 per blade/
4 per panel
PPL-2U-HD-FX/
PPL-2U-HD-FX-OPEN
up to 6 per blade/
24 per panel
up to 4 per blade/
16 per panel
up to 3 per blade/
12 per panel
up to 2 per blade/
8 per panel
PPL-4U-HD-FX up to 6 per blade/
48 per panel
up to 4 per blade/
32 per panel
up to 3 per blade/
24 per panel
up to 2 per blade/
16 per pane
Each blade has 12 lanes
Requires 2 lanes Requires 3 lanes Requires 4 lanes Requires 6 lanes
28067-A
17.42 IN. (44.25 CM)
11.51 IN.
(29.24 CM)
8.45 IN.
(21.47 CM)
1RU PANEL (FRONT VIEW)
2RU PANEL (FRONT VIEW)
1RU PANEL (TOP VIEW)
1RU PANEL (SIDE VIEW)
2RU PANEL (SIDE VIEW)
18.31 IN. (46.51 CM)
19.00 IN. (48.25 CM)
3.46 IN.
(8.79 CM)
1.74 IN.
(4.42 CM)
3.06 IN.
(7.78 CM)
QR CODE
(ENLARGED)

TC-96342-IP
Page 13
© 2023 CommScope. All Rights Reserved.
Figure 7 shows a fully occupied blade. The components shown are 3 of the available 4 sizes. The
largest component, which occupies half of the blade, is not shown. As shown in Figure 8, Propel
components can be installed from the front or rear of a blade.
Figure 7. Fully Loaded Blade
Figure 8. Connection Components Can Be Installed from Front or Rear
2.5 QR Codes
Propel products are labeled with QR codes providing different types of information of interest to the
user. Included are the QR code types described below.

TC-96342-IP
Page 14
© 2023 CommScope. All Rights Reserved.
2.5.1 Product QR Codes on Panel
Each panel is affixed with a QR code that goes to the Propel Panels product page in the
CommScope electronic catalog. The product page has documentation, including specifications, the
quick start guide, and electronic only user manuals, for all types of Propel panels. Other customer
aides such as videos when available are also placed on the product page for viewing online or
downloading by the customer
Figure 9 shows the front QR code location on the Propel Fixed and Fixed Open Panel. Figure 10
shows the rear QR code locations in the Propel Fixed and Fixed Open Panel.
Figure 9. Front QR Code Location, Propel Fixed and Fixed Open Panel
28096-A
FRONT QR CODE LOCATION
ON PROPEL PANEL FRONT DOOR

TC-96342-IP
Page 15
© 2023 CommScope. All Rights Reserved.
Figure 10. Rear QR Code Location, Propel Fixed and Fixed Open Panel
2.5.2 Component QR Codes
Each Propel connection component (module, adapter pack, or splice cassette) has a label specific
to that particular item. The label is sized to the width of the component and has information such as
the item serial number (for a module only) and test results. See Figure 11.
REAR QR CODE LOCATION
PROPEL FIXED OPEN PANEL
28096-A
REAR QR CODE LOCATION
PROPEL FIXED PANEL

TC-96342-IP
Page 16
© 2023 CommScope. All Rights Reserved.
Figure 11. Example of Propel Connection Component Labeling
3 UNPACKING AND INSPECTION
Use the following procedure to unpack and inspect the product. Verify parts against Table 5 below.
1. Inspect the exterior of the shipping container(s) for evidence of rough handling that may
have damaged the components in the container.
2. Unpack each container while carefully checking the contents for damage.
3. If damage is found or parts are missing, contact the CommScope Support Center using the
URL: http://www.commscope.com/SupportCenter
4. Save any damaged cartons for inspection by the carrier.
For an exploded view of product packaging, refer to Figure 12 for the Propel Fixed Panel and to
Figure 13 for the Propel Fixed Open Panel.
Table 5. Propel Fixed Panel Parts List
Description Quantity
Propel Fixed Panel Quick Start (TC-96341-IP or TC-96355-IP) 1
Propel Fixed Panel (1RU, 2RU, 4RU, 1RU-OPEN, or 2RU-OPEN) 1
Panel fastener pack 1 per panel
ITEM SPECIFIC QR CODE
27523-A
PORT NUMBERS
ITEM SERIAL NUMBER
CATALOG NUMBER
MANUFACTURER COUNTRY AND DATE

TC-96342-IP
Page 17
© 2023 CommScope. All Rights Reserved.
Figure 12. Unpacking a Propel Fixed Panel
28074-A
ON 4RU PANEL, REMOVE
AND DISCARD (2) TRANSIT
SCREWS FROM REAR
DOOR (IDENTIFIED WITH
YELLOW LABELS).
NOTE:NOTE:

TC-96342-IP
Page 18
© 2023 CommScope. All Rights Reserved.
Figure 13. Unpacking a Propel Fixed Open Panel
4 OVERVIEW OF INSTALLATION
Installing the panel and accessories involves the following procedures:
• Determining rack size and mounting hardware (covered in Section 5.1 on Page 19).
• Installing kits for alternative rack sizes (not 19-inch) (Section 5.2 on Page 19).
• Selecting panel recess options for a fixed panel (Section 5.3 on Page 19).
• Selecting panel recess options for a fixed open panel (Section 5.4 on Page 21).
• Mounting the panel on a rack (Section 5.5 on Page 23).
• Installing connection components (Section 5.6 on Page 25).
• Installing cables (Section 5.7 on Page 27).
• Installing patch cords (Section 5.8 on Page 29).
The installation procedures listed above describe the sequential steps for a typical installation in a
way that facilitates going quickly and efficiently through the installation. For operational details for
covers, doors, connection components, cables, cable management clips, and patch cords, refer to
28069A

TC-96342-IP
Page 19
© 2023 CommScope. All Rights Reserved.
Section 6 on Page 30. Refer to these sub-sections during installation if any problem arises in
moving through the installation procedures.
5 INSTALLING THE PANEL
5.1 Determining Rack Size and Mounting Hardware
The Propel Fixed Panel is shipped with mounting brackets suitable for mounting on a 19-inch
equipment rack or cabinet.
Accessory kits are available for mounting on a 23-inch or ETSI rack. Whatever the type of rack
being used, four recess options are available for positioning the mounting brackets.
The mounting brackets shown in illustrations are those used for 19-inch rack mounting. Refer to the
following sections for more information.
5.2 Installing Kits for Alternative Rack Sizes (Not 19-Inch)
5.2.1 23-Inch Rack (584mm) Mount Kit
To mount the panel on a 23-inch (584mm) rack, use the G2-23BRKT accessory kit (one kit per RU,
available separately) and install two conversion brackets to the pre-installed mounting brackets,
using the four #10-32 x 3/8-inch conversion screws included in the accessory kit.
Use one conversion bracket and two screws per side. Mount the panel to rack using four #12-24 x
1/2-inch screws (provided as part of basic panel).
5.2.2 ETSI Rack Mount Kit
To mount the panel on an ETSI rack, use the G2-23BRKT accessory kit (available separately) and
install one conversion bracket to either of the pre-installed mounting brackets, using two of four
#10-32 x 3/8-inch conversion screws included in accessory kit.
The panel will not be centered when mounted in rack.
Mount the panel to rack using four M6 x 12mm screws (provided as part of basic panel).
5.3 Panel Recess Options, Fixed Panel
The Propel Fixed Panel is shipped with the mounting brackets in a 3-inch offset position for front of
rack mounting.
The mounting brackets can be relocated to 3.5-inch or 6-inch offset positions for front of rack
mounting, or to a 9-inch offset position for rear of rack mounting.
Note: The mounting brackets are stamped with the letter “1” at key locations to assist in
orienting the mounting brackets in the following procedures.

TC-96342-IP
Page 20
© 2023 CommScope. All Rights Reserved.
5.3.1 Mounting Bracket Position on Panel as Shipped
Figure 14 shows the mounting bracket position when shipped.
Figure 14. Rack Mounting Position for 3.0-Inch Recess (Shipped Panel)
5.3.2 Mounting Bracket in 3.5-Inch Offset Position (Front of Rack Mounting)
Figure 15 shows the mounting bracket in the 3.5-inch offset position for front of rack mounting. To
mount a mounting bracket at this position, remove screws from holes marked “1” and remount the
mounting bracket using the unmarked holes shown in Figure 15.
Figure 15. Rack Mounting Position for 3.5-Inch Recess
5.3.3 Mounting Bracket in 6-Inch Offset Position (Front of Rack Mounting)
Figure 16 shows the mounting bracket in the 6-inch offset position for front of rack mounting. To
mount a mounting bracket at this position, remove screws from holes marked “1” and rotate the
bracket 180 degrees. Reinstall 4 screws in holes marked “1”.
Note: The holes used for this mounting location are stamped with a “1” on the physical bracket
and are also shown in these illustrations.
3.0 IN. (7.62 CM)
28076-A
3.5 IN. (8.89 CM)
28077-A