CommScope T750SE User manual

Unleashed T750SE Access
Point
Quick Setup Guide
This Quick Setup Guide provides step-by-step instrucons on how to eld-
install the RUCKUS Unleashed T750SE access point (AP). For detailed
informaon on installaon, management and operang the T750SE, refer
to the Unleashed Online Help, available at hps://
docs.ruckuswireless.com/unleashed/200.9.
WARNING! Only trained and qualied personnel should be allowed to
install, replace, or service this equipment.
WARNING! Installaon of this equipment must comply with local and
naonal electrical codes.
CAUTION! Make sure that you form a 80mm - 130mm (3”-5”) drip loop
in any cable that is aached to the AP or the building. This will prevent
water from running along the cable and entering the AP or the building
where the cable terminates.
CAUTION! Be sure that grounding is available and that it meets local
and naonal electrical codes. For addional lightning protecon, use
lightning rods and lightning arrestors.
CAUTION! Make sure that proper lightning surge protecon
precauons are taken according to local electrical code.
WARNING! RUCKUS WIRELESS strongly recommends that you wear eye
protecon before mounng the T750SE.
This Guide in Other Languages
•请从以下网站获得该指南的简体中文版 hps://
support.ruckuswireless.com.
•Vous trouverez la version française de ce guide à l'adresse suivante
hps://support.ruckuswireless.com.
•このガイドの日本語版は hps://support.ruckuswireless.com でご覧
ください。
•이 가이드의 한국어 버전은 웹 사이트 (hps://
support.ruckuswireless.com) 에서 확인하시기 바랍니다.
•Veja a versão em português (Brasil) deste guia em hps://
support.ruckuswireless.com.
•Puede ver la versión en español (América Lana) de esta guía en
hps://support.ruckuswireless.com.
Before You Begin
Before deploying RUCKUS WIRELESSs products, please check for the latest
soware and the release documentaon.
•Release Notes and other user documentaon are available at hp://
support.ruckuswireless.com/documents.
•Soware upgrades are available at hp://support.ruckuswireless.com/
soware.
•Soware license and limited warranty informaon are available at
hp://support.ruckuswireless.com/warranty.
Before deploying your RUCKUS WIRELESS Access Point, verify that all
items listed in Package Contents are included in the package. If any item
is damaged or missing, nofy your authorized RUCKUS WIRELESS sales
representave. Also, make sure that you have the required hardware
and tools.
Required Hardware and Tools
•1/2” (13 mm) at-blade screwdriver or equivalent
•No. 2 Phillips screwdriver
•Small at-blade screwdriver
•Torque wrench or torque screwdriver with sockets
•Long-nose pliers
•Electrical wire stripping and terminal crimping pliers
•Pipe, pole or a sturdy at surface
•Electric drill with drill bits and customer-supplied wall anchors, at
washers, and hex nuts for at-surface mount
Package Contents
A complete T750SE eld installaon package includes all of the items listed
below :
•T750SE Access Point
•M25 data cable gland extender
•Three M25 data cable glands
•Outdoor AP Mounng Bracket kit
•One ground wire with lug
•Cloud Management Statement
•Cable gland extender gasket
•AC Connector
•Zipcord cable gland grommet
•Four 1/2” (12.7 mm) wide adjustable clamps, 2.5” (63.5 mm) diameter,
for main mounng bracket on smaller poles
•Safety cable kit
•Service Level Agreement/Limited Warranty Statement
•Declaraon of Conformity
•Regulatory Statement
•RUCKUS WIRELESS AP Geng Started Guide
•This Quick Setup Guide
Unleashed Network Conguraon
Setup Using the Unleashed Mobile App
To perform setup using the Unleashed Mobile App, download the iOS or
Android app from the app store.
1. As soon as the Unleashed AP is powered on and connected to the
local network, it boots up and begins broadcasng a temporary
unencrypted WLAN named “Congure.Me-[xxxxxx]” from both radios.
2. Using your client’s Wi-Fi connecon sengs, select and associate to
the “Congure.Me-[xxxxxx]” WLAN.
3. Launch the app, and follow the on-screen instrucons to congure
your Unleashed network(s).
FIGURE 1 Unleashed Mobile App for iOS and Android
FIGURE 2 Conguring Unleashed from the Mobile App
Copyright © 2020 CommScope, Inc. All rights reserved. Page 1 of 8
Published July 2020, Part Number 800-72628-001 Rev A

Setup Using a Web Browser
1. As soon as the Unleashed AP is powered on and connected to the
local network, it boots up and begins broadcasng a temporary
unencrypted WLAN named “Congure.Me-[xxxxxx]” from both radios.
2. Using your client’s Wi-Fi connecon sengs, select and associate to
the “Congure.Me-[xxxxxx]” WLAN.
3. Launch a web browser and enter the following into the browser’s URL
bar: unleashed.ruckuswireless.com, and press Enter.
4. You will be redirected to the Setup Wizard. Complete the steps in the
Setup Wizard and click Finish.
FIGURE 3 Complete the Setup Wizard to set up your Unleashed
network
5. Once the Setup Wizard is nished, a “Conguring system sengs and
reboong” progress screen appears. Wait unl the process is
complete.
6. Connect to the WLAN that you congured in the Setup Wizard, and
click OK to reconnect. You will be redirected to the Unleashed login
screen.
7. Enter your Admin Name and Password to login.
FIGURE 4 The Login page
8. Upon successful login you will be presented with the Unleashed
Dashboard, which displays an overview of your Ruckus Unleashed
network.
Mounng Instrucons
Connecng and Sealing the RJ-45 Cables
The T750SE may use zero, or one or two RJ-45 cables, one for Ethernet
when congured as a Root AP (RAP), and another when the T750SE is
supplying PoE out to a peripheral device, such as a small cell or micro cell
radio, and zero when using the SFP as a backhaul alternate with AC power.
When the T750SE uses RJ-45 cables, connect and seal the cables using the
M25 data cable glands as shown in Figure 2.
FIGURE 5 T750SE AP PoE IN and PoE OUT ports
1. SFP port
2. PoE IN
3. PoE OUT
4. AC port
WARNING! Do not use any PoE injector not tested and approved by
RUCKUS WIRELESS to power the T750SE Access Point.
WARNING! Do not plug PoE IN power into the PoE OUT port. See Figure
1.
1. Feed the end of the cable through the gland dome, rubber grommet,
clamping ring assembly and cable gland base, as shown in Figure 2.
NOTE: Do not seat the clamping ring and rubber grommet into the
cable gland base unl the cable gland base has been torqued to
specicaons.
FIGURE 6 RJ-45 Cable and Cable Gland Assembly
1. Cable gland base
2. Clamping ring
3. Rubber grommet
4. Gland dome
2. Use a wide at-blade screwdriver to remove the required (PoE OUT or
PoE IN) blanking cap from the T750SE.
3. Connect the cable to the Ethernet port in the AP.
4. Tighten the cable gland base to 7 N.m (62 in-lbs).
5. Wrap the clamping ring assembly around the rubber grommet. Make
sure that the clamping ring assembly fully encloses the rubber
grommet.
6. Seat the clamping ring assembly and rubber grommet in the cable
gland base.
7. Hand-ghten the gland dome.
Copyright © 2020 CommScope, Inc. All rights reserved. Page 2 of 8
Published July 2020, Part Number 800-72628-001 Rev A

Connecng the SFP Opc Module Using a Single
Diameter Cable
You can use a single diameter cable to connect to the SFP opc module.
FIGURE 7 SFP module cable gland assembly
1. SFP transceiver
2. Cable gland gasket
3. Cable gland extender
4. Cable gland gasket
5. Clamping ring
6. Cable gland grommet / zipcord
cable gland grommet
7. Gland dome
8. Fibre cable
WARNING! The ber cable is extremely fragile and must be handled
with care.
NOTE: Do not insert the cable gland base/grommet/dome into the
extender unl the extender has been ghtened. Step 5 must be
performed before Step 6, else the ber cable will twist.
1. Place the cable gland base to the cable gland extender and ghten
the cable gland base to 7 N.m (62 in-lbs).
2. Fix the Cable gland extender gasket to the cable gland extender.
3. Feed the ber cable through the gland dome, cable gland grommet,
clamping ring, cable gland base, cable gland extender, and cable gland
gasket as shown in Figure 3.
4. Connect the ber cable to the SFP transceiver in the AP.
5. Tighten the cable gland extender to 7 N.m (62 in-lbs).
6. Insert the cable gland grommet into the clamping ring with the ber
cable in the center.
7. Insert the clamping ring into the cable gland base.
8. Tighten the cable gland dome to 7 in-lbs.
The SFP module is hot-swappable and can be removed with ngers or
simple tools.
Connecng the SFP Opc Module Using a Zipcord
Cable
You can use a zipcord cable to connect to the SFP opc module.
WARNING! The zipcord ber cable is extremely fragile and must be
handled with care.
NOTE: Do not insert the cable gland base/grommet/dome into the
extender unl the extender has been ghtened. Step 5 must be
performed before Step 6, else the ber cable will twist.
1. Place the cable gland base to the cable gland extender and ghten
the cable gland base to 7 N.m (62 in-lbs).
2. Fix the Cable gland extender gasket to the cable gland extender.
3. Feed the zipcord ber cable through the gland dome, zipcord cable
gland grommet, clamping ring, cable gland base, cable gland
extender, and cable gland gasket as shown in Figure 3.
4. Connect the zipcord ber cable to the SFP transceiver in the AP.
5. Tighten the cable gland extender to 7 N.m (62 in-lbs).
6. Insert the zipcord cable gland grommet into the clamping ring with
the zipcord ber cable in the two holes.
FIGURE 8 Zipcord grommet with cable
7. Insert the clamping ring into the cable gland base.
8. Tighten the cable gland dome to 7 in-lbs.
The SFP module is hot-swappable and can be removed with ngers or
simple tools.
Aaching the U-Joint Bracket to the Mounng Bracket
1. Posion the U-joint bracket on the mounng bracket.
NOTE: Mount the U-joint bracket in any direcon on the mounng
bracket, preferably to allow AP azimuth adjustments. Then the AP
bracket allows AP elevaon adjustments.
FIGURE 9 U-joint bracket aached horizontally to the mounng
bracket
1. Bolts
2. U-joint bracket
3. Mounng bracket
2. Use four 1/4 - 28 bolt and washer sets (1) to mount the U-joint
bracket (2) to the mounng bracket (3). Tighten the bolts to 9.5 N.m
(84 in-lbs).
3. Connue with Aaching the Mounng Bracket to a Flat Surface on
page 3.
Aaching the Mounng Bracket to a Flat Surface
1. Place the mounng bracket at the locaon on the at surface where
you want to mount the AP. Use the holes on the mounng bracket as
a template to mark the locaons of the mounng holes.
FIGURE 10 Mounng bracket at surface holes
2. Remove the mounng bracket from the at surface.
3. Drill holes required for the mounng hardware.
NOTE: The hardware required for mounng to a wall are not
included in the mounng kit.
4. Aach the mounng bracket to the at surface using the mounng
hardware.
5. Using the mounng hardware instrucons, ghten the hardware to
secure the mounng bracket.
6. Connue with Aaching the Mounng Bracket to a Pole on page 4.
Copyright © 2020 CommScope, Inc. All rights reserved. Page 3 of 8
Published July 2020, Part Number 800-72628-001 Rev A

Aaching the Mounng Bracket to a Pole
1. Insert the open end of one steel clamp into the upper two slots on
the mounng bracket.
2. Take the other steel clamp and insert it into the lower two slots on
the mounng bracket.
NOTE: The clamps can be daisy-chained together to accommodate
larger poles.
3. Use the clamps to aach the mounng bracket to the pole. Tighten
the clamps to 3 N.m (27 in-lbs) or per manufacturer’s specicaons.
FIGURE 11 Aaching the mounng bracket to a vercal pole
4. Connue with Mounng the Linkage Bracket to the U-Joint Bracket on
page 4.
Mounng the Linkage Bracket to the U-Joint Bracket
1. The linkage bracket aaches to the U-joint bracket using an M8 bolt
and washer set. The linkage bracket is symmetrical, and either end
can be aached to the U-joint bracket.
NOTE: Make sure that linkage bracket is installed with its serrated
external-tooth lock washer on the inside of the U-joint bracket
anges. This ensures that the azimuth adjustment does not
change.
2. Loosely assemble the linkage bracket (1), the U-joint bracket (3), one
serrated external-tooth lock washer (2), and one M8 bolt and washer
set (4).
FIGURE 12 Aaching the linkage bracket to the U-joint bracket
1. M8 bolt
2. Lock washer
3. Flat washer
4. External-tooth lock
washer
5. Linkage bracket
6. U-joint bracket
3. Set the azimuth required by the AP.
4. Tighten the M8 bolt to 13.6 N.m (120 in-lbs).
5. Connue with Aaching the AP Bracket to the Linkage Bracket on
page 4.
Aaching the AP Bracket to the Linkage Bracket
Aach the AP bracket to the linkage bracket using the included bolt, lock
washer, at washer, serrated external-tooth washer and nut shown in the
illustraon below.
The linkage bracket is symmetrical, and either end can be aached to the
AP bracket.
Loosely assemble the AP bracket to the linkage bracket using the M8 bolt,
washer and nut set.
FIGURE 13 Aach the linkage bracket to the AP bracket
1. M8 bolt
2. Locker washer
3. Flat washer
4. External-tooth lock washer
5. Linkage bracket
6. AP bracket
7. Nut
NOTE: Make sure that the linkage bracket is installed with its serrated
external-tooth lock washer on the inside of the AP bracket anges. This
ensures that the elevaon adjustment does not change.
Aaching the AP Bracket to the Access Point
1. Place the AP bracket onto the back side of the AP so that the four
larger screw holes on the bracket align with the four screw holes on
the AP.
Copyright © 2020 CommScope, Inc. All rights reserved. Page 4 of 8
Published July 2020, Part Number 800-72628-001 Rev A

FIGURE 14 Aaching the AP bracket to the AP
1. AP
2. AP bracket
3. Flat washer
4. Lock washer
5. Hex bolts
2. Use four 0.5-inch x 0.250-28 hex bolts with split lock and at washer
sets to mount the AP bracket to the AP. Tighten the bolts to 2.5-3.0
N.m (22-27 in-lbs).
CAUTION! Make sure that the screws are no longer than 0.5 inch.
If a screw is longer than 0.5 inch, it can damage the AP chassis.
NOTE: This kit may include extra screws, nuts and washers. You
may use the extras where required.
3. Connue with Set the Elevaon and Tighten the Elevaon Bolt on
page 5.
Set the Elevaon and Tighten the Elevaon Bolt
1. Set the elevaon required by the AP.
2. Tighten the M8 bolt to 13.6 N.m (120 in-lbs).
3. Connue with Powering the AP with AC on page 7.
External Antenna and Cabling Need to be Purchased
Separately
If the External Antenna opon is chosen over the internal sector antenna,
the External Antenna and Antenna Cable must be purchased separately.
NOTE: Beamex is not available with external antennas.
Mounng and Connecng 5 GHZ and 2.5 GHZ External
Antennas
NOTE: Mount the external antenna per manufacturer's instrucons.
1. Disconnect the AP from all power sources.
2. Unscrew the metal caps that protect the antenna connectors.
3. Connect external antennas to the N-type female antenna connectors
on the AP. Use a torque wrench to ghten the connectors to 1.58 N.m
(14 in-lb).
4. If the antennas come with RF coaxial cables (for example, a patch
antenna), physically mount the antennas at your desired locaon,
preferably on the same mounng structure as the AP.
FIGURE 15 T750SE Rear View
T750SE
Connecons
External Antenna Connecon
Vercal Horizontal
ANT0 X
ANT1 X
ANT2 X
ANT3 X
5. Apply weatherproong tape to the antenna connectors as described
in Connector Sealing Instrucons on page 5.
CAUTION! If you are not connecng external antennas to the AP,
make sure that the metal caps remain installed and securely
fastened to protect the interfaces from elements, such as water
and dirt.
Connector Sealing Instrucons
NOTE: N-Type connectors shown are representave examples.
NOTE: Applying sealing tape to both ends of the cable is recommended.
Step 1: Cleaning the Connectors and Your Hands
1. Clean all traces of dust, grease, and oil from your hands
2. Clean o any traces of dust, grease, and oil from the N-type bulkhead
connector external threads
3. Make sure that the connectors are dry before connuing.
Step 2: Connecng the Cable with the Connector
1. If the AP is powered on, disconnect the AP from the power source.
CAUTION! Make sure that you disconnect the AP from the power
source to avoid electrocuon or equipment damage.
FIGURE 16 Connecng the Cable with the Connector
2. Unscrew the metal cap that protects the antenna connector. Place the
metal cap in a safe place, in case you need it later.
3. Connect the cable to the connector. Use a torque wrench to ghten
the cable coupling nut to 1.58 N.m (14 in-lb). If you do not have a
torque wrench or if you are ghtening a knurled coupling nut (as
shown), hand-ghten the cable coupling nut unl the internal gaskets
are compressed, but do not overghten.
Step 3: Wrapping the Exposed Connector Threads
1. Depending on the width of the sealing tape, either fold the tape in
half or cut it to t the exposed connector threads
2. Stretch the tape per the manufacturer’s instrucons
3. Working clockwise, gently stretch the sealing tape as you install it so
that it covers the connector thread between the cable coupling nut
and the base of the connector.
Make sure that the nal wrap is approximately ush with the cable
coupling nut, and then cut the sealing tape.
Copyright © 2020 CommScope, Inc. All rights reserved. Page 5 of 8
Published July 2020, Part Number 800-72628-001 Rev A

FIGURE 17 Wrapping the Exposed Connector Threads
NOTE: Cut, do not tear, the sealing tape. If the sealing tape is
overstretched, it loses its self-amalgamang properes.
Step 4: Wrapping the Internal Layer of the Electrical
Tape
1. Using scissors, cut the end of the electrical tape at an angle. This will
allow the electrical tape to be applied with minimal bulk.
FIGURE 18 Cung the End of the Electrical Tape
2. Wrap the electrical tape clockwise from the beginning of the cable
coupling nut to just past the heat shrink tube on the cable. Do not
cover the sealing tape installed in Step 3: Wrapping the Exposed
Connector Threads on page 5.
FIGURE 19 Wrapping the Electrical Tape
Step 5: Wrapping the Main Sealing Tape
1. Using scissors, cut the end of the sealing tape at an angle. This will
allow the sealing tape to be applied with minimal bulk.
FIGURE 20 Cung the Sealing Tape at an Angle
2. Working clockwise, gently stretch the sealing tape from the beginning
of the sealing tape installed in Step 3: Wrapping the Exposed
Connector Threads on page 5 and connue wrapping to 12 mm (0.5
in.) past the electrical tape installed in Step 4: Wrapping the Internal
Layer of the Electrical Tape on page 6.
NOTE: Cut, do not tear, the sealing tape. If the sealing tape is
overstretched, it loses its self-amalgamang properes.
FIGURE 21 Wrapping the Sealing Tape
3. Gently knead the sealing tape from top to boom to make sure there
are no gaps and to amalgamate the sealing tape.
Step 6: Wrapping the Outer Layer of Electrical Tape
1. Using scissors, cut the end of the electrical tape at an angle. This will
allow the electrical tape to be applied with minimal bulk.
FIGURE 22 Cung the Electrical Tape at an Angle
2. Wrap the electrical tape clockwise to completely cover the sealing
tape and connue wrapping to 12 mm (0.5 in.) past the sealing tape
installed in Step 5: Wrapping the Main Sealing Tape on page 6.
Copyright © 2020 CommScope, Inc. All rights reserved. Page 6 of 8
Published July 2020, Part Number 800-72628-001 Rev A

FIGURE 23 Wrapping the Electrical Tape
Step 7: Repeang for the Other Cables
Repeat the connector sealing instrucons for the three antenna
connectors, as shown in Figure 18.
FIGURE 24 Repeang for Other Cables
Step 8: Creang Cable Drip Loops
Physically mount the AP and antennas at your desired locaon, preferably
on the same mounng structure.
Form 80-mm to 130-mm (3-in. to 5-in.) drip loops with the cables.
FIGURE 25 Creang Cable Drip Loops
Earth Grounding the AP
CAUTION! Make sure that earth grounding is available and that it meets
local and naonal electrical codes. For addional lightning protecon,
use lightning rods and lightning arrestors.
NOTE: The color coding of ground wires varies by region. Before
compleng this step, check your local wiring standards for guidance.
Using the factory-supplied ground wire and ground screw/washer set,
connect a good earth ground to the AP chassis ground point.
CAUTION! The T750SE AP includes one 9 mm stainless steel M6 x1
earth ground screw with split lock and at washers. Make sure that any
replacement screw is no longer than 9 mm. If a screw is longer than 9
mm, it can damage the AP chassis.
FIGURE 26 Connect good earth ground to AP
1. Earth ground screw
Congratulaons! You have mounted your T750SE access point.
Powering the AP with AC
1. Separate the AC cable connector parts by unscrewing the boot from
the cable gland and the cable gland from the connector housing..
2. Feed the end of the AC cable through the boot and cable gland.
3. Strip the AC cable as shown.
4. Insert the stripped part of the conductors into the appropriate
terminals on the connector housing. The conductors are color coded
and must be connected to the appropriate terminals as shown in
gure below.
NOTE: The color coding of wire conductors varies by region. Before
compleng this step, check your local wiring standards for
guidance.
Copyright © 2020 CommScope, Inc. All rights reserved. Page 7 of 8
Published July 2020, Part Number 800-72628-001 Rev A

FIGURE 27 Assembling the AC power connector
Wire Stripping (Not Actual Size)
1. (Neutral/Return): White
or Gray (US), Blue (EU)
2. (Line/Hot): Black (US),
Brown (EU)
3. (not used)
4. (Earth Ground): Green
(US), Green/Yellow (EU)
5. Using a small screwdriver, ghten the small screws around the
connector housing to x the connector pins into the terminals.
6. Mate the cable gland with the connector housing, and then hand-
ghten.
NOTE: Two dierent-sized grommets are supplied in the AC
connector assembly kit. Use the grommet that is appropriate to
the diameter of the AC cable that you are using.
7. Mate the boot with the cable gland, and then hand-ghten to seal.
8. Connect the AC cord connector that you have assembled to the AC
power socket on the AP.
9. Connect the AC cord to an AC power source.
Installing the Security Cable
1. Thread the security cable through the mounng bracket (1 in Figure
12) and through the eye on the cable itself (2 in Figure 12).
2. Aach the safety cable to the AP (3 in Figure 12).
FIGURE 28 Aaching the security cable
Troubleshoong
CAUTION! If required, you can reset the AP to its factory default
sengs by pressing the reset buon located inside the PoE IN port. Use
the p of a pen or a 3mm at blade screwdriver to press the reset
buon. Press and hold the reset buon for 4+ seconds to restore to
factory defaults. DO NOT RESET THE AP TO FACTORY DEFAULT SETTINGS
UNLESS SO INSTRUCTED. (Doing this resets the AP IP address to
192.168.0.1.)
NOTE: Aer a reset, you can access the internal AP web interface using
hps://192.168.0.1. Your device must use any other address from
192.168.0.2 through 192.168.0.254, with subnet mask 255.255.255.0.
The username is super, and the password is sp-admin. Refer to the
Outdoor Access Point User Guide for informaon on conguring and
operang the AP. This document is available at hps://
support.ruckuswireless.com.
For More Informaon
For informaon on how to congure and manage the AP, refer to the
RUCKUS Access Point User Guide, available from hps://
support.ruckuswireless.com.
RUCKUS WIRELESS, Inc. is a wholly owned subsidiary of CommScope, Inc.
© 2020 CommScope, Inc. All rights reserved.
ARRIS, the ARRIS logo, COMMSCOPE, RUCKUS, RUCKUS WIRELESS, the Ruckus
logo, and the Big Dog design are trademarks of CommScope, Inc. and/or its
aliates. Wi-Fi Alliance, Wi-Fi, the Wi-Fi logo, Wi-Fi Cered, the Wi-Fi
CERTIFIED logo, Wi-Fi Protected Access, the Wi-Fi Protected Setup logo, Wi-Fi
Protected Setup, Wi-Fi Mulmedia and WPA2 and WMM are trademarks or
registered trademarks of Wi-Fi Alliance. All other trademarks are the property of
their respecve owners.
Copyright © 2020 CommScope, Inc. All rights reserved. Page 8 of 8
Published July 2020, Part Number 800-72628-001 Rev A