Confer Plastics 635-52 User guide

SAFETY RULES
* One person on the ladder at a time
* Ladder MUST be installed per manufacturer’s instructions
* DANGER: No Jumping or Diving from ladder
* Face ladder when entering and leaving pool
* To prevent entrapment or drowning —
DO NOT swim through, behind or around ladder
* Ladder to be used as a swimming pool ladder only.
* Weight limit - 250 lbs maximum
*Warning: Exceeding the maximum weight restriction
may cause the ladder to fail.
* Consult your local Building Department before
installation of your pool and equipment.
*DANGER:
Use a cordless drill for assembly and installation
Never use an electric drill in or around the pool.
CONFER PLASTICS, INC.
LIMITED, PRO-RATED WARRANTY
Confer Plastics, Inc. warrants their swimming pool ladders to be free from defects in workmanship for one year from
date of purchase. After the first year the cost to replace a part is as follows:
MODEL #635-52
2nd Year - 20%
3rd Year - 40%
4th Year - 60%
5th Year - 80%
Plus shipping/handling
Enclose proof-of-purchase (receipts, etc.) showing date purchased, your name, address, and daytime phone number. You
will be notified of cost to replace part.
This warranty gives you specific legal rights, and you may also have other rights which may vary from state to state.
MODEL 635-52
ALL PLASTIC INPOOL LADDER
ASSEMBLY AND INSTRUCTION MANUAL
CONFER LADDERS ARE DESIGNED FOR EASE OF ASSEMBLY AND ARE CONSTRUCTED
OF MAINTENANCE-FREE, NON-CORROSIVE RESINS AND MATERIALS.
Note: WARRANTY ON PAGE 4. PLEASE SAVE THIS BOOKLET AND YOUR WARRANTY.
MADE IN THE U.S.A. BY:
CP 635-52 10/07Printed in U.S.A.
97 Witmer Road
North Tonawanda, NY 14120-2421
Toll Free U.S. 866-396-2968
Tel: [phone] / FAX: [phone]
www.conferladders.com
4
• 635-52 Fits Decks 46"-56"
• Easy Assembly
• Adjustable Handrail
Mounting System
Made in U.S.A. by
SAVE THESE INSTRUCTIONS
DEALER/INSTALLER: GIVE TO HOMEOWNER
*Model 635-52 is a
straight up-and-down
ladder and should be
installed 3" to 6" from
the pool wall.
Note: 10 Lbs of
sand required
(See Step 2)
DO NOT RETURN DEFECTIVE PART TO DEALER
The defective part should be returned, postpaid, to:
Confer Plastics, Inc.
97 Witmer Road
North Tonawanda, N.Y. 14120-2421
of current parts
list price
SAND
Confer A frame 635-52_R6:Confer A frame 635-52_R1 10/11/07 12:06 PM Page 1

2
Step 1. Step 2.
Step 4.
Step 3.
Slide the
handrails onto
the legs.
DO NOT
secure with
screws at
this stage.
If needed coat tubes
with liquid soap or
lubricant. Push the
adjustable tubes through
mounting blocks. Push
the adjustable tubes up
into the handrails.
Pour 5 lbs
of sand
into each leg.
Fill remainder
with water.
Install threaded cap
over bottom drain hole.
Adjustable tube
Mounting block
Step 5. Step 6.
Place the ladder into the pool and position mounting
blocks on deck. Slide the adjustable tubes up or down
as needed until mounting blocks are sitting flush on
the deck. Ladder MUST rest on pool bottom. If not,
EB100 riser(s) are required. (See page 3 to order)
Drill four pilot holes (1/8") through holes in
each block into wood surface. Fasten blocks
to deck using the four #10 x 1-1/4" screws per
mounting block. Drill three holes through each
side of each handrail at the pre-marked
locations. Fasten using three #10 x 1-1/4" screws.
Slide down into position
once mounting blocks
have been fastened.
Flush to deck
CONFER PLASTICS, INC.
Model #635-52
ASSEMBLY INSTRUCTIONS - PLEASE READ BEFORE ATTEMPTING ASSEMBLY
Used to raise ladder when deck is built higher
than pool. Maximum 2 risers.
Fill with sand and
water, rest ladder on top. Straps included.
Platform provides extra “step” at top of ladder.
Prevents swimmers from stepping on pool top.
3
NOTE: Check with your dealer for availability first
or order online at: www.conferladders.com
SKIMS OFF DEBRIS
Cut cleaning time 75% with skimmer extension
that guides debris directly into your skimmer.
Fits most in-ground and above-ground pool
skimmers. Corrosion-resistant plastic Skim-It
installs in seconds without tools.
IMPORTANT
FOR YOUR SAFETY
* Check the contents of the carton with the Parts list
for this ladder.
* If any parts are missing call Toll Free U.S. -
866-396-2968 or visit our web site at
www.conferladders.com
*DO NOT attempt to assemble or install the ladder
if there are ANY shortages of parts or hardware.
* For proper assembly and installation follow all
instructions in the sequence shown.
* Before using the product, after assembly and
installation, go over the instructions and procedures
again to make sure nothing has been overlooked.
* Be sure and safe. The manufacturer IS NOT
responsible for improper assembly, installation
and use.
Parts List Tools Needed for Assembly
2 - Handrails * Sand - 10 lbs
1 - Ladder Section * Cordless Drill Motor
* 1/8" Drill Bit
Hardware Pack * Phillips Screwdriver
14 - #10 x 1-1/4" Screws * Tape Measure
1 - Threaded Cap * Liquid Soap or Lubricant
2 - Mounting Blocks
2 - Adjustable Tubes
If missing parts call - Toll free U.S. - 866-396-2968 or www.conferladders.com
For winterizing in cold climates remove ladder from the pool, and drain water from ladder.
Adjustable
Tube
Ladder
Handrail
Mounting
Block
ADDITIONALACCESSORIES
For #635-52 Ladder
SKIM-IT
EB 100-3" RISER DK300 DECK KIT
Confer A frame 635-52_R6:Confer A frame 635-52_R1 10/11/07 12:06 PM Page 3

2
Step 1. Step 2.
Step 4.
Step 3.
Slide the
handrails onto
the legs.
DO NOT
secure with
screws at
this stage.
If needed coat tubes
with liquid soap or
lubricant. Push the
adjustable tubes through
mounting blocks. Push
the adjustable tubes up
into the handrails.
Pour 5 lbs
of sand
into each leg.
Fill remainder
with water.
Install threaded cap
over bottom drain hole.
Adjustable tube
Mounting block
Step 5. Step 6.
Place the ladder into the pool and position mounting
blocks on deck. Slide the adjustable tubes up or down
as needed until mounting blocks are sitting flush on
the deck. Ladder MUST rest on pool bottom. If not,
EB100 riser(s) are required. (See page 3 to order)
Drill four pilot holes (1/8") through holes in
each block into wood surface. Fasten blocks
to deck using the four #10 x 1-1/4" screws per
mounting block. Drill three holes through each
side of each handrail at the pre-marked
locations. Fasten using three #10 x 1-1/4" screws.
Slide down into position
once mounting blocks
have been fastened.
Flush to deck
CONFER PLASTICS, INC.
Model #635-52
ASSEMBLY INSTRUCTIONS - PLEASE READ BEFORE ATTEMPTING ASSEMBLY
Used to raise ladder when deck is built higher
than pool. Maximum 2 risers.
Fill with sand and
water, rest ladder on top. Straps included.
Platform provides extra “step” at top of ladder.
Prevents swimmers from stepping on pool top.
3
NOTE: Check with your dealer for availability first
or order online at: www.conferladders.com
SKIMS OFF DEBRIS
Cut cleaning time 75% with skimmer extension
that guides debris directly into your skimmer.
Fits most in-ground and above-ground pool
skimmers. Corrosion-resistant plastic Skim-It
installs in seconds without tools.
IMPORTANT
FOR YOUR SAFETY
* Check the contents of the carton with the Parts list
for this ladder.
* If any parts are missing call Toll Free U.S. -
866-396-2968 or visit our web site at
www.conferladders.com
*DO NOT attempt to assemble or install the ladder
if there are ANY shortages of parts or hardware.
* For proper assembly and installation follow all
instructions in the sequence shown.
* Before using the product, after assembly and
installation, go over the instructions and procedures
again to make sure nothing has been overlooked.
* Be sure and safe. The manufacturer IS NOT
responsible for improper assembly, installation
and use.
Parts List Tools Needed for Assembly
2 - Handrails * Sand - 10 lbs
1 - Ladder Section * Cordless Drill Motor
* 1/8" Drill Bit
Hardware Pack * Phillips Screwdriver
14 - #10 x 1-1/4" Screws * Tape Measure
1 - Threaded Cap * Liquid Soap or Lubricant
2 - Mounting Blocks
2 - Adjustable Tubes
If missing parts call - Toll free U.S. - 866-396-2968 or www.conferladders.com
For winterizing in cold climates remove ladder from the pool, and drain water from ladder.
Adjustable
Tube
Ladder
Handrail
Mounting
Block
ADDITIONALACCESSORIES
For #635-52 Ladder
SKIM-IT
EB 100-3" RISER DK300 DECK KIT
Confer A frame 635-52_R6:Confer A frame 635-52_R1 10/11/07 12:06 PM Page 3