Confer Plastics PES-1X User manual

SINGLE UNIT
Model PES-1X
TWO UNITS WITH GATE
Model PES-DBLX
Printed in U.S.A.
97 Witmer Road
North Tonawanda, New York 14120-2421
Toll Free U.S. 800-635-3213 • FAX [phone]
www.conferladders.com
S
MADE IN THE USA
POOL ENTRY SYSTEM
ADJUSTS TO FIT 48” TO 54” POOLS AND DECKS
ASSEMBLY, INSTALLATION and USE MANUAL
Assembly video available online: www.conferplastics.com
WEIGHT LIMIT 400 LBS.
To reduce the risk of drowning, entrapment, falls, paralysis, electrocution, or
other serious injury or death:
Dealer/Installer: Give manual to homeowner.
Installer: Read "Safe Installation" on page # 2 and all instructions before beginning. For proper assembly and
installation, instructions must be followed completely.
Homeowner: Read "Safe Use" on back cover before using. Save these instructions.
Installation must comply with local codes and may require permits.

2
RISER
GROOVE
FASTENING
FLANGE
RISER
RECESS
SECOND PERSON TO ASSIST
Tools Needed For Assembly
• Mallet
• Phillips Screwdriver
• Cordless Drill
• 1/8” Drill Bit
• Level
• Hacksaw
• Knife
• Tape Measure
Assembly Instructions
CONFER PLASTICS, INC. POOL ENTRY SYSTEM FOR ABOVE-GROUND POOLS
Adjusts to fit most above-ground pools with flat or slightly dished bottoms
Bill of Materials
Safe Installation
To reduce the risk of electrocution, drowning, entrapment, falls, or other serious injury
or death:
Check building codes/permitting. Consult your local Building Department before installation of your pool and equipment.
Pool/equipment installation must comply with the codes of the authority having jurisdiction and may require permits (e.g.,
building, plumbing, electrical, zoning, etc.).
Use for intended purpose only
• Use only as a swimming pool ladder.
• This ladder is designed and manufactured for a specic pool wall height and/or deck of the pool - check product
specication and the height of your pool.
Check that you have all required parts. Check the contents of the carton with the Parts List for this ladder. All parts and
hardware are required. If any parts are missing, DO NOT attempt to assemble or install the ladder. Instead, call Toll
Free U.S. - 800-635-3213 or visit our web site at www.conferladders.com for assistance.
Select an appropriate location - The ladder must be located on a level, solid base and in a location that will be in full view
of competent adult supervision when in use.
Follow all instructions
• For stable, correct assembly and installation, all instructions must be followed completely and in the sequence shown.
• Follow the manufacturer’s recommendations for the safe use of all hand tools and equipment used during installation.
Cordless drill only - no corded drills near pool. Use a cordless drill for assembly and installation. To reduce the risk of
electrocution, NEVER use a corded drill in or around a pool.
Lift safely. When lifting awkward or heavy loads, have another person help you.
Double check after installation
• Before using the product, after assembly and installation, go over the instructions and procedures again to make sure
nothing has been overlooked.
• Make sure that safety labels are installed and legible.
Parts List - Single Unit
Code# Qty. Description CTN#
1 2 Side Panel 2
7 2 Anti-Entrapment Panel 2
8 4 Threaded Height Adjuster
(Factory Installed) 2
2 5 Step w/4 wedges 1
3 4 Riser 1
4 1 Kickplate 1
5 1 Deck Connector 1
6 2 Base 1
Hardware Pak - Single Unit
Qty. Description CTN#
31/4 - 20 Hex Nut 1
31/4 - 20 X 1” Screw 1
3#10 x 1-1/4” Self Tapping Screw 1
2Large Plug/Side Panels 1
1Label for Top Riser 1
2Threaded Cap 1
2Red Plug 1
1 Instructions 1








3
Step 5.
After determining the correct height from measure-
ment #2 in step 1, cut the kickplate to the appropriate
height. Use a hacksaw to cut the ends (next to the
pre-scored line) and a knife to separate the kickplate
at the pre-scored line. Place the kickplate in position
below the bottom step.
Step 2.
Carefully remove
the wedges from
every step using a
utility knife. Do not
discard.
Remove Wedges and SAVE.
They will be needed in step 7
Affix the warning
label to center of
top riser.
FOR DECK ATTACHMENT, MEASURE FROM HERE.
MEASURE FROM HERE FOR
2 UNITS ATTACHED
(GROUND LEVEL ENTRY).
TO ACCOUNT FOR THE POOL
TOP SEAT, ADD 1/2” TO
MEASUREMENTS.
MEASUREMENT #2
8”
36”
WRITE MEASUREMENTS
MEASUREMENT #1 ______
MEASUREMENT #2 ______
1. Measure the Depth of Your Pool.
A) For Deck Level Pool Entry (one (1) unit
attached to a deck), measure from the top
of the deck to the bottom of the pool approxi-
mately eight (8) inches out from the pool wall
(Measurement #1). Take a second measure-
ment approximately three (3) feet out from the
pool wall (Measurement #2).
B) For Ground Level Pool Entry (two (2) units
attached to each other), take the measure-
ments from the top of the pool top seat. Add
one-half (1/2) inch to these measurements for
clearance.
*Whether you use method “A” or “B”, write your
measurements for future reference.
Step 1.
48” to 50”, Cut Here
50” to 52”, Cut Here
52” to 54”, Cut Here
Step 3.
Lay the side panel on a clean flat surface. Firmly push
the protrusion of the steps into the opening of the hand-
rail section. Insert the risers into the grooves on the
steps as shown above. Note: position risers so center
hole faces “back” of steps.
The risers slip into
grooves on steps.
Protrusion
Opening
Step 4.
Continue adding steps and risers until all are firmly
in position.
MEASUREMENT #1

Step 7.
Secure each
step by tapping
a locking wedge
(saved from Step
2) between the side
panel and the top
surface of the
step protrusions.
Step 6.
Push the second side panel firmly down on the step
protrusions. It may be necessary to tap the side panel
using a hammer and block of wood until seated
correctly.
Push down firmly
4
Step 8.
Red plug
Threaded cap
Step 10.
If you are fastening
the pool entry system
to a deck: Attach the
deck connector to the
top step using the
three (3) 1/4-20x1”
screws and hex nuts
(nuts are installed on
underside of deck
connector).
NOTE: If you are fastening
two units together, do not
attach deck connector. Skip
to Page 5 “Joining two PES
Pool Entry Systems”.
The maximum
adjusted height
of the Entry
System is
(541 /2) inches.
3 1/4-20 x 1” screws
3 hex nuts
Step 11.
Attach the anti-entrapment panel (item 7)
to both sides of the unit as shown. Position and push firmly
down into base until it locks securely into place.
Note: Anti-Entrapment panels are not needed if the
unit is left at 48”.
Step 9.
Use a mallet to
tap each base
onto the height
adjusters.
With a
screwdriver, turn the height
adjusters to the desired height as
determined in Step 1.
Proper exposed length
is measurement #2
minus 48-1/2”
To attach the base,
position the unit as
shown.
Proper exposed length is
measurement #1 minus 48-1/2”
WARNING! Using
a corded drill near
pool may result in
electrocution.
On the bottom edge
of each side panel
is a drain hole. Plug
these holes by first
inserting a (Red)
plug into the hole
and then covering
with the threaded
cap.

5
Step 12.
Water fill
openings on
both side
panels.
To prevent
algae, add
a cup of
household
bleach
(optional).
Joining two Pool Entry Systems.
When joining two units together, the deck
connectors will not be used. Assemble both
units and position the in-pool unit in the
desired location, after filling it in the same
manner as step #12.
WARNING! Verify that your chosen
location will be in full view of competent
adult supervision when in use.
Allow approximately two (2) inches of clearance between the side of the pool
(pool liner) and the Entry System. Make any necessary height adjustments
to ensure that all four (4) threaded adjustors are supporting the unit, that
the unit is level and does not wobble, and that the underside of the top step
is about (1/2) inch above the pool top seat. The outside unit should rest on
cement patio blocks. Position and level the outside unit so that both units
can be joined using the six (6) 1/4-20 x 1” machine screws and hex nuts.
The hex nuts should be on the outside of the fastening flange of the side
panels (See diagram on pg 2). Press the large plugs into the fill
opening of the outside unit. It is not necessary to fill the outside
unit with water.
Note: Gate instructions and hardware are supplied with the gate.
Step 13.
Note: Two people are
required for this operation
Step 14.
Attach with 3 #10 x 1-1/4”
Self Tapping Screws
2” x 4” x 28-
1
/
4
” LONG
2-
1
/
2
” LONG LAG SCREWS
#10 x 1-1/4” LONG
SELF-TAPPING SCREWS
DECK FACEBOARD
Carefully submerge the unit into the pool. Add water to
the side panels through the water fill openings located
near the top of each side panel. When completely filled,
press the supplied (large white) plugs into the openings
on both side panels.
Tilt the unit to allow the steps to fill with water. When
bubbling ceases, steps are filled. Steps must be filled
completely to prevent floating.
Position the PES with attached deck connector and with
a cordless drill, drill three pilot holes. Attach to deck using
3 #10 x 1-1/4” Self Tapping Screws. Keep 2” clearance
between unit and pool wall.
WARNING! Using
a corded drill near
pool may result in
electrocution.
WARNING! Pool step will
be heavy. Have additional
help. Do not attempt to
place the step by yourself.
Adjust the height of the entry system so that the
top step, at minimum, reaches the face board of
the deck, however, the height of the bottom surface
of the top step must not exceed (54-1/2) inches.
Cut a piece of 2 x 4 pressure treated lumber (28-
1/4” long) and place it edge down on the top step
between the two flanges of the side panels. Secure
in place with four #10 x 1-1/4” screws (not provided)
through the two lower holes in each of the mounting
flanges of the side panel. After securing the 2 x 4
to the unit, position the unit so that the 2 x 4 meets
the face board of the deck. It can then be secured
in place using wood lag screws. Three 2-1/2” long
lag screws are required (Lag screws not provided).
Optional mounting method when deck height is greater than (54-1/2) inches.

6
Order online @
www.conferladders.com
3-PESX-89A
PES-1X / PES-DBLX 5M 2/19
Removal and storage of Pool Entry System:
In cold climates the Entry System must be removed from the pool
and drained to prevent freezing and cracking.
WARNING! Pool step will be heavy and must be lifted from within
the pool. Have additional help when removing from swimming
pool. Do not attempt to remove by yourself.
To remove the unit disconnect it from the deck (or the outside unit),
pull large plugs and tip it so that some of the water drains from the
large fill openings. Once the unit is lighter it will become buoyant
so that it can be turned onto its side and the bottom drain caps and
plugs can be removed. With the unit on its side, slowly pull the Entry
System from the water allowing the water to drain out of the unit.
Once the unit is out of the pool be sure that all the water drains out.
If desired the unit can be disassembled for winter storage. Use a flat
blade screwdriver to remove the locking wedges and carefully pull
the side panels away from the steps. (Be sure to save all caps and
locking wedges for reassembly).
To reinstall, follow installation instructions steps 10-12.
OPTIONAL ACCESSORY
SKIM-IT—SKIMS OFF DEBRIS.
Cut cleaning time 75% with skim-
mer extension that guides debris
directly into your skimmer.
Fits most in-ground and above-
ground pool skimmers. Corrosion-
resistant plastic Skim-It installs in
seconds without tools.
CONFER PLASTICS INC. FIVE YEAR WARRANTY
Confer Plastics Inc. warrants their swimming pool ladders and steps to be free from
defects in workmanship for five years from date of purchase.
DO NOT RETURN DEFECTIVE PART TO DEALER
E-MAIL CONFER PLASTICS AT: [email protected]
A PICTURE [S] OF DEFECTIVE PART, A BRIEF DESCRIPTION OF PROBLEM,
PROOF OF PURCHASE AND YOUR CONTACT INFORMATION.
INFORMATION MAY ALSO BE FAXED TO CONFER PLASTICS AT: 716-694-3102
OR MAILED TO THE ADDRESS BELOW. UPON REVIEW OF THE INFORMATION YOU
WILL BE NOTIFIED IF PART IS COVERED UNDER THE WARRANTY AND
THE SHIPPING/HANDLING CHARGES.
This warranty gives you specific legal rights, and you may also have other rights which may vary from state to state.
Confer Plastics Inc.
97 Witmer Road
North Tonawanda, N.Y. 14120-2421
Safe Use
To reduce the risk of drowning, entrapment, falls, paralysis, electrocution,
or other serious injury or death:
Use step system properly.
• No diving or jumping from steps - shallow water; risk of paralysis or death.
• ONE PERSON ON THE LADDER/STAIR AT A TIME.
• Illuminate the steps when using the pool at night.
Weight limit - 400 lbs maximum. Exceeding maximum weight may cause the stairs to fail.
Secure stairs when not in use. When pool is not in use, make sure gate is closed and locked.
Watch children at all times when they are in or around water to help prevent drowning.