Confer Plastics PES-G Setup guide

SAVE THESE INSTRUCTIONS
DEALER/INSTALLER: GIVE TO HOMEOWNER
MODEL PES-G GATE ASSEMBLY
Can be used on Pool Entry System, SIG System and STEP Enclosure Kit
ASSEMBLY AND INSTALLATION MANUAL
WARNING: GATE MUST BE PADLOCKED WHEN NOT IN USE.
CONFER PLASTICS, INC.
Now with
Automatic Gate Closer!
NEW!!

BILL OF MATERIALS
Parts List Required Part #
Gate 1 6-Gate-01
Hinge Mounting Post 1 6-Gate-02
Latch Mounting Post 1 6-Gate-03
Hardware Pack Required Part #
#10 x 1-1/4” Screw 20 3-00-14C
#7 x 1/2” Screw 8 3-Gate-01
Padlock 1 3-00-03
Gate Latch with Latch Bar 1 3-Gate-06
Gate Closer 1 3-Gate-07
Step #1
Spread open the flange of the
hinge mounting post and slide
it down over the right side
panel until the bottom edge of
the hinge post and the bottom
edge of the side
panel are even.
Step #2
Fasten the hinge post to the
side panel using six of the
#10 x 1-1/4” self-tapping
screws at the pre-marked
spots on each side of the
hinge post (3 per side).
Step #3
Slide the open gate hinge
through the hinge post pin
opening and wrap the gate
hinge around the hinge pin.
Fasten the hinge at the four
pre-marked spots using the
#7 x 1/2” self-tapping screws
(4 per hinge).
#10 x 1-1/4”
Self-tapping
Screw
#7 x 1/2”
Self-tapping
Screw
2
Tools Required
Cordless Drill
1/16 Drill Bit
Phillips Screwdriver Bit
Silicone Spray or
Spray Lubricant
POOL ENTRY SYSTEM GATE ASSEMBLY
MODEL # PES-G

Step #4
Spread open the flange of the
latch mounting post and slide it
down over the left side panel.
Slide the post up or down until
the support knob closes properly
into the recess on the post.
Once the latch post is aligned so
the gate closes properly fasten
the post to the side panel using
six (6) #10 x 1-1/4” screws.
Step #6
Close the gate and align the
latch bar by locking it into the
gate latch as shown. Secure the
latch bar to the gate with two (2)
#10 x 1-1/4” screws.
Step #7
Install the gate closer in the
indented portion provided
on the hinge post. Follow
the directions provided
with the gate closer package.
DO NOT use the slide plate.
It is for metal/wood finish
wear and will not work with
our gravity hinge.
Step #5
Install the latch on the mounting
block located on the upper
portion of the latch using
four (4) #10 x 1-1/4” screws.
3
WARNING: GATE MUST BE LOCKED WHEN POOL IS NOT IN USE.
Note: Spraying the gate hinges with a silicone spray will aid in the self-closing action.
The PES-G now includes a gate closer.
Mount the closer on the flat recessed are
on the hinge post (see diagram to left).
To adjust tension on the closer after
installation see detailed instructions on
closer package.

97 Witmer Road
North Tonawanda, New York 14120-2421
Toll Free U.S. 866-396-2968
716-283-1826/ FAX [phone]
www.conferladders.com
Printed in U.S.A.
MADE IN THE U.S.A. by:
SAFETY RULES
* Always follow the manufacturer’s recommendations for the safe
use of all hand tools and equipment.
* When electrically powered hand tools and /or equipment are
used outdoors, or where wet conditions are conducive to shocks,
use a ground fault circuit interrupter.
*DO NOT use the Confer-Gate for any purpose other than that for
which it is intended.
* When lifting awkward or heavy loads, have another person
help you.
* Always padlock gate when not in use.
* Consult your local Building Department before
installation of your pool and equipment.
*DANGER:
Use a cordless drill for assembly and installation.
Never use an electric drill in or around the pool.
CP-PES-G 1M 01/08
4
CONFER PLASTICS, INC.
LIMITED, PRO-RATED WARRANTY
Confer Plastics, Inc. warrants their swimming pool ladders to be free from defects in workmanship for one year from
date of purchase. After the first year the cost to replace a part is as follows:
MODEL #PES-G
2nd Year - 20%
3rd Year - 40%
4th Year - 60%
5th Year - 80%
Plus shipping/handling
Enclose proof-of-purchase (receipts, etc.) showing date purchased, your name, address, and daytime phone number. You
will be notified of cost to replace part.
This warranty gives you specific legal rights, and you may also have other rights which may vary from state to state.
DO NOT RETURN DEFECTIVE PART TO DEALER
The defective part should be returned, postpaid, to:
Confer Plastics, Inc.
97 Witmer Road
North Tonawanda, N.Y. 14120-2421
of current parts
list price