Congatec conga-IGX User manual

conga-IGX Mini ITX SBC
Mini-ITX Professional Series single board computer based on AMD Embedded G-Series SoC
User’s Guide
Revision 0.2 (Preliminary)

Copyright © 2014 congatec AG IGX1m02 2/134
Revision History
Revision Date (yyyy.mm.dd) Author Changes
0.1 2014.05.13 AEM • Preliminary release
0.2 2014.05.28 AEM • Updated section 12.1 “System Watchdog (WD)” and section 15.1.1 “If you want to open the Boot Menu Immediately”
• Deleted section 17.1 “Erase Disk” and section 22.6.1 “Diagnostic Program” because the conga-IGX does not support these features.

Copyright © 2014 congatec AG IGX1m02 3/134
Preface
This user’s guide provides information about the components, features and connectors available on the conga-IGX Mini-ITX SBC (Single Board
Computer).
Disclaimer
The information contained within this user’s guide, including but not limited to any product specication, is subject to change without notice.
congatec AG provides no warranty with regard to this user’s guide or any other information contained herein and hereby expressly disclaims
any implied warranties of merchantability or tness for any particular purpose with regard to any of the foregoing. congatec AG assumes
no liability for any damages incurred directly or indirectly from any technical or typographical errors or omissions contained herein or for
discrepancies between the product and the user’s guide. In no event shall congatec AG be liable for any incidental, consequential, special, or
exemplary damages, whether based on tort, contract or otherwise, arising out of or in connection with this user’s guide or any other information
contained herein or the use thereof.
Intended Audience
This user’s guide is intended for technically qualied personnel. It is not intended for general audiences.
Lead-Free Designs (RoHS)
All congatec AG designs are created from lead-free components and are completely RoHS compliant.
Electrostatic Sensitive Device
All congatec AG products are electrostatic sensitive devices and are packaged accordingly. Do not open or handle a congatec AG product
except at an electrostatic-free workstation. Additionally, do not ship or store congatec AG products near strong electrostatic, electromagnetic,
magnetic, or radioactive elds unless the device is contained within its original manufacturer’s packaging. Be aware that failure to comply with
these guidelines will void the congatec AG Limited Warranty.

Copyright © 2014 congatec AG IGX1m02 4/134
Symbols
The following symbols are used in this user’s guide:
Warning
Warnings indicate conditions that, if not observed, can cause personal injury.
Caution
Cautions warn the user about how to prevent damage to hardware or loss of data.
Note
Notes call attention to important information that should be observed.
Copyright Notice
Copyright © 2014, congatecAG.All rights reserved.All text, pictures and graphics are protected by copyrights. No copying is permitted without
written permission from congatec AG.
congatec AG has made every attempt to ensure that the information in this document is accurate yet the information contained within is
supplied “as-is”.
Trademarks
Product names, logos, brands, and other trademarks featured or referred to within this user’s guide, or the congatec website, are the property
of their respective trademark holders. These trademark holders are not afliated with congatec AG, our products, or our website.

Copyright © 2014 congatec AG IGX1m02 5/134
Warranty
congatec AG makes no representation, warranty or guaranty, express or implied regarding the products except its standard form of limited
warranty (“Limited Warranty”) per the terms and conditions of the congatec entity, which the product is delivered from. These terms and
conditions can be downloaded from www.congatec.com. congatec AG may in its sole discretion modify its Limited Warranty at any time and
from time to time.
The products may include software. Use of the software is subject to the terms and conditions set out in the respective owner’s license
agreements, which are available at www.congatec.com and/or upon request.
Beginning on the date of shipment to its direct customer and continuing for the published warranty period, congatec AG represents that the
products are new and warrants that each product failing to function properly under normal use, due to a defect in materials or workmanship or
due to non conformance to the agreed upon specications, will be repaired or exchanged, at congatec’s option and expense.
Customer will obtain a Return Material Authorization (“RMA”) number from congatec AG prior to returning the non conforming product freight
prepaid. congatec AG will pay for transporting the repaired or exchanged product to the customer.
Repaired, replaced or exchanged product will be warranted for the repair warranty period in effect as of the date the repaired, exchanged
or replaced product is shipped by congatec, or the remainder of the original warranty, whichever is longer. This Limited Warranty extends to
congatec’s direct customer only and is not assignable or transferable.
Except as set forth in writing in the Limited Warranty, congatec makes no performance representations, warranties, or guarantees, either
express or implied, oral or written, with respect to the products, including without limitation any implied warranty (a) of merchantability, (b) of
tness for a particular purpose, or (c) arising from course of performance, course of dealing, or usage of trade.
congatec AG shall in no event be liable to the end user for collateral or consequential damages of any kind. congatec shall not otherwise be
liable for loss, damage or expense directly or indirectly arising from the use of the product or from any other cause. The sole and exclusive
remedy against congatec, whether a claim sound in contract, warranty, tort or any other legal theory, shall be repair or replacement of the
product only.
Certication
congatec AG is certied to DIN EN ISO 9001 standard.
C
E
R
T
I
F
I
C
A
T
I
O
N
I
S
O
9
0
0
1
TM

Copyright © 2014 congatec AG IGX1m02 6/134
Technical Support
congatec AG technicians and engineers are committed to providing the best possible technical support for our customers so that our products
can be easily used and implemented. We request that you rst visit our website at www.congatec.com for the latest documentation, utilities and
drivers, which have been made available to assist you. If you still require assistance after visiting our website then contact your local congatec
sales representative.
Terminology
Term Description
SBC Single Board Computer
SoC System on Chip
PCI Express (PCIe) Peripheral Component Interface Express – next-generation high speed Serialized I/O bus
PCI Express Lane One PCI Express Lane is a set of 4 signals that contains one differential line for
transmitter and one differential line for receiver. Clocking information is embedded into the
data stream.
x1, x2, x4, x16 x1 refers to one PCI Express Lane of basic bandwidth; x2 to a collection of two PCI Express
Lanes; etc. Also referred to as x1, x2, x4 or x16 link.
VGA Video Graphics Array
USB Universal Serial Bus
SATA Serial ATAttachment: serial-interface standard for hard disks
AC ‘97/HDA Audio CODEC (Coder-Decoder) / High Denition Audio
LPC Low Pin-Count Interface: a low speed interface used for peripheral circuits such as Super
I/O controllers, which typically combine legacy-device support into a single IC.
I²C Bus Inter-Integrated Circuit Bus: is a simple two-wire bus with a software-dened protocol that
was developed to provide the communications link between integrated circuits in a system.
SM Bus System Management Bus: is a popular derivative of the I²C-bus.
SPI Bus Serial Peripheral Bus
GBE Gigabit Ethernet
LVDS Low-Voltage Differential Signaling
TPM Trusted Platform Module
HDMI High Denition Multimedia Interface
DVI Digital Visual Interface
S/PDIF Sony/Philips Digital Interface Format
DDC Display Data Channel is an I²C bus interface between a display and a graphics adapter.
N.C. Not connected
N.A. Not available
T.B.D. To be determined

Copyright © 2014 congatec AG IGX1m02 7/134
Contents
1 Safety Instructions ...................................................................12
2 System Memory Conguration.................................................13
3 Feature Overview conga-IGX ..................................................14
3.1 conga-IGX Reference Silkscreen.............................................14
3.2 Block Diagram..........................................................................15
3.3 USB Structure..........................................................................16
3.4 conga-IGX Variants..................................................................17
3.5 External Connectors conga-IGX..............................................18
3.6 Onboard Components..............................................................19
3.7 Heatsink Installation Notes ......................................................20
3.8 Heatsink Installation Notes ......................................................21
4 Heatsink/Heatpipe Installation Notes.......................................22
5 Display Options........................................................................23
5.1 Basic Display Features............................................................23
5.2 LVDS Display & Backlight Inverter Connection........................24
5.3 LVDS Connector details ..........................................................25
5.4 Backlight Inverter Connector Details .......................................27
5.5 LVDS Timing & Screen Resolution .........................................28
5.6 LVDS Tool ................................................................................32
5.7 LVDS Cabling Reference.........................................................33
5.8 Dual-DVI Output.......................................................................34
5.9 VGA Output..............................................................................35
5.10 DVI or VGA plus LVDS.............................................................36
5.11 Internal & External graphics use in parallel..............................37
6 Power Supply Features............................................................38
6.1 12V / 19-24V DC Connector ....................................................38
6.2 Requirements for 12V / 19-24V operation ...............................39
6.3 Power option for internal devices.............................................40
6.3.1 Requirements for DC operation...............................................40
6.3.2 Limited conga-IGX output current............................................40
6.4 Drive Power Connector............................................................41
6.5 Drive Power Connector............................................................42
7 Internal Connectors..................................................................43
7.1 Feature Connector ..................................................................43
7.2 Internal USB 2.0 Ports.............................................................44
7.3 Internal USB 3.0 Ports.............................................................45
7.4 Internal Audio Ports – Front panel Audio ................................46
7.5 Internal Audio Ports - SPDIF....................................................47
7.6 m-SATA / SATA ........................................................................47
7.7 Mini-PCIe Connector................................................................48
7.8 Internal Serial Connector (COM3) ...........................................48
7.9 Internal Parallel Port Connector ..............................................49
7.10 PCI Express Extension Slot.....................................................49
7.11 Intrusion Connector..................................................................50
7.12 Fan Connector.........................................................................51
7.13 Front Panel Connector.............................................................52
7.14 Additional Jumper Settings......................................................52
8 System Monitoring...................................................................53
8.1 conga-IGX: Fans......................................................................53
8.2 conga-IGX Sensors .................................................................54
8.3 SilentFanCongManager .........................................................55
8.4 Temperature Reference Points conga-IGX..............................56
9 Power Consumption.................................................................58
9.1 Sample Conguration ..............................................................58
10 Operating System Support.......................................................59
10.1 MS Windows / MS Windows Embedded Compact..................59
10.2 Linux Support ..........................................................................59
11 conga-IGX Tools ......................................................................60
11.1 Common conga-IGX Tools ......................................................60
12 Miscellaneous..........................................................................61

Copyright © 2014 congatec AG IGX1m02 8/134
12.1 System Watchdog (WD)...........................................................61
12.2 Trusted Platform Module (TPM)...............................................62
12.3 RealTime Clock (RTC) Accuracy .............................................62
12.4 BIOS/CMOS Reset (“BIOS Setup Defaults”) ...........................62
13 Known Issues and Important Notes.........................................63
13.1 Support for MS Windows XP ...................................................63
13.2 Graphics Memory.....................................................................63
13.3 AMD “Eyenity” Support ..........................................................63
13.4 HDMI Audio Support ................................................................63
13.5 Audio: Recording Level via HDA Front Panel .........................63
13.6 Video Playback (WMV, MP4)...................................................64
14 Introduction..............................................................................65
14.1 Notational conventions............................................................65
15 Navigating BIOS Setup ...........................................................67
15.1 Open BIOS Setup ..................................................................67
15.1.1 If you want to open the Boot Menu immediately....................67
15.1.2 If you wish to boot immediately from LAN.............................68
15.2 Navigating BIOS Setup...........................................................68
15.3 Exiting BIOS Setup .................................................................68
16 Main Menu – System functions...............................................69
16.1 System Information.................................................................69
16.1.1 Board and Firmware Details...................................................69
16.1.2 Network Controller Details......................................................70
16.1.3 Processor Details....................................................................70
16.1.4 Memory MemoDetails .............................................................70
16.2 System Language ...................................................................71
16.3 System Date/System Time......................................................71
16.4 Access Level...........................................................................71
17 Advanced Menu – Advanced system conguration ................72
17.1 TPM (Trusted Platform Module) Computing............................73
17.1.1 TPM Support...........................................................................73
17.1.2 TPM State...............................................................................73
17.1.3 Pending TPM operation..........................................................73
17.1.4 Current TPM Status Information.............................................74
17.2 SATA Conguration .................................................................74
17.2.1 SATA Mode ............................................................................ 74
17.2.2 mSATA Support........................................................................74
17.3 Graphics Conguration ...........................................................75
17.3.1 Primary Display.......................................................................75
17.3.2 Internal Graphics.....................................................................75
17.3.3 IGD Memory............................................................................75
17.4 LVDS Conguration .................................................................75
17.4.1 LVDS Support..........................................................................76
17.4.2 LVDS Panel Cong Select......................................................76
17.4.3 Non-EDID Support ..................................................................76
17.4.4 LVDS Mode .............................................................................76
17.4.5 LVDS Channel Swap..............................................................77
17.4.6 LVDS Backlight-Enable Polarity ..............................................77
17.4.7 LVDS Brightness Control ........................................................77
17.4.8 LVDS Brightness .....................................................................78
17.4.9 POST Screen Mode .............................................................. 78
17.5 USB Conguration...................................................................78
17.5.1 USB Devices...........................................................................78
17.5.2 Legacy USB Support..............................................................78
17.5.3 USB Transfer Time-Out...........................................................79
17.5.4 Mass Storage Devices............................................................79
17.6 USB Port Security...................................................................79
17.6.1 USB Port Control....................................................................80
17.6.2 USB Device Control................................................................80
17.7 System Monitoring...................................................................80
17.7.1 Controller Revision..................................................................80
17.7.2 Firmware Version.....................................................................80
17.7.3 Chassis Type...........................................................................81
17.7.4 TCV Version........................................................................... 81
17.7.5 Fan Control .............................................................................81
17.7.6 Fan2 Wiring.............................................................................82

Copyright © 2014 congatec AG IGX1m02 9/134
17.8 Onboard Device Conguration................................................82
17.8.1 Audio Conguration.................................................................82
17.8.2 High Precision Event Timer Conguration ..............................82
17.8.3 LAN 1......................................................................................83
17.8.4 LAN 2......................................................................................83
17.9 Super IO Conguration ...........................................................83
17.9.1 Super IO Chip ........................................................................83
17.10 Serial Port 0 Conguration .....................................................83
17.10.1 Serial Port ...............................................................................83
17.10.2 Device Settings .......................................................................84
17.10.3 Change Settings......................................................................84
17.11 Serial Port 1 Conguration.....................................................84
17.11.1 Serial Port ...............................................................................85
17.11.2 Device Settings .......................................................................85
17.11.3 Change Settings......................................................................85
17.12 Parallel Port Conguration......................................................85
17.12.1 Parallel Port.............................................................................86
17.12.2 Device Settings .......................................................................86
17.12.3 Change Settings......................................................................86
17.12.4 Device Mode...........................................................................86
17.13 Network Stack.........................................................................87
17.13.1 Ipv4 PXE Support...................................................................87
17.13.2 Ipv6 PXE Support...................................................................87
18 Security Menu – Security Functions........................................88
18.1 Password Description.............................................................88
18.2 Administrator Password...........................................................89
18.3 User Password........................................................................89
18.4 User Password on Boot.........................................................90
18.5 Cabinet Monitoring..................................................................90
18.6 Skip Password on WOL.........................................................90
18.7 FLASH Write ...........................................................................90
18.8 Secure Boot............................................................................91
18.8.1 Platform Mode.........................................................................91
18.8.2 Secure Boot ............................................................................91
18.8.3 Secure Boot Control...............................................................91
18.8.4 Secure Boot Mode..................................................................92
18.8.5 Key Management....................................................................92
18.9 HDD Security Conguration....................................................95
18.9.1 HDD Password on Boot .........................................................95
18.10 HDD n / HDD-ID.....................................................................95
18.10.1 HDD Password Description ....................................................95
18.10.2 HDD Password Conguration .................................................95
18.10.3 Security Supported..................................................................95
18.10.4 Security Enabled.....................................................................95
18.10.5 Security Locked.......................................................................96
18.10.6 Security Frozen.......................................................................96
18.10.7 HDD User Password Status...................................................96
18.10.8 HDD Master Password Status................................................96
18.10.9 Set User Password.................................................................96
18.10.10 Set Master Password .............................................................96
19 Power Menu – Energy saving functions...................................97
19.1 Power Settings ........................................................................97
19.1.1 Power LED in S3 ...................................................................97
19.1.2 Power On Source ...................................................................98
19.1.3 Low Power Soft Off................................................................98
19.1.4 Power Failure Recovery...........................................................98
19.1.5 Hibernate like Soft Off............................................................99
19.1.6 USB At Power Off................................................................. 99
19.2 Wake-Up Resources................................................................99
19.2.1 LAN ..........................................................................................99
19.2.2 Wake On LAN Boot..............................................................100
19.2.3 Wake Up Timer.....................................................................100
19.2.4 Hour .......................................................................................100
19.2.5 Minute ....................................................................................100
19.2.6 Second...................................................................................100
19.2.7 Wake Up Mode.....................................................................100
19.2.8 Wake Up Day .......................................................................101
19.2.9 USB Keyboard ......................................................................101

Copyright © 2014 congatec AG IGX1m02 10/134
20 Event Logs – Conguration and Display of the Event Log.102
20.1 Change SMBIOS event log settings.....................................102
20.1.1 SMBIOS Event Log ..............................................................102
20.1.2 Erase Event Log...................................................................103
20.1.3 When Log is full...................................................................103
20.1.4 Log System Boot Event .......................................................103
20.1.5 MECI......................................................................................103
20.1.6 METW....................................................................................103
20.1.7 Log OEM Codes...................................................................104
20.1.8 Convert OEM codes .............................................................104
20.1.9 View SMBIOS Event Log .....................................................104
21 Boot Menu – System boot....................................................105
21.1 Boot Conguration.................................................................106
21.1.1 Bootup NumLock State.........................................................106
21.1.2 Quiet Boot.............................................................................106
21.1.3 Fast On .................................................................................107
21.1.4 USB Support.........................................................................107
21.1.5 PS2 Devices Support ...........................................................108
21.1.6 POST Errors ........................................................................ 108
21.1.7 Remove Invalid Boot Options.............................................. 108
21.1.8 Boot Removable Media ........................................................108
21.1.9 Virus Warning ........................................................................109
21.1.10 Prefer USB Boot...................................................................109
21.1.11 Boot option priorities.............................................................109
21.1.12 CSM Conguration................................................................ 110
22 Save & Exit Menu – Finish BIOS Setup ................................ 112
22.1 Save Changes and Exit.......................................................112
22.2 Discard Changes and Exit – quit without saving...................112
22.3 Save Changes and Reset .................................................... 113
22.4 Discard Changes and Reset................................................113
22.5 Save Options ........................................................................113
22.5.1 Save Changes....................................................................... 113
22.5.2 Discard Changes................................................................... 113
22.5.3 Restore Defaults.................................................................... 113
22.5.4 Save as User Defaults......................................................... 113
22.5.5 Restore User Defaults .......................................................... 113
22.6 Boot Override .......................................................................114
23 BIOS Update ......................................................................... 115
24 Appendix: LVDS Reference Cable Pinouts............................ 116
24.1 AUO_G0121SN01 LVDS Cable Pinout.................................. 117
24.1.1 Panel Pinout AUO G0121SN01 ............................................. 117
24.1.2 Inverter Cable Plan................................................................ 118
24.1.3 Inverter Pinout Green C&C GH093A ..................................... 118
24.2 AUO_G150XG01 LVDS Cable Pinout ................................... 119
24.2.1 Panel Pinout AUO G150XG01............................................... 119
24.2.2 Inverter Cable Plan................................................................120
24.2.3 Inverter Pinout Green C&C GH001A.....................................120
24.3 AUO-M170EG01-VD LVDS Cable Pinout..............................121
24.3.1 Panel Pinout AUO M170EG01-VD.........................................121
24.3.2 Inverter Cable Plan................................................................122
24.3.3 Inverter Pinout Green C&C GH053A.....................................122
24.4 AUO-M190EG01 V0 LVDS Cable Pinout...............................123
24.4.1 Panel Pinout AUO-M190EG01 V0 .........................................123
24.4.2 Inverter Cable Plan................................................................124
24.4.3 Inverter Pinout Green C&C GH053A.....................................124
24.5 Sharp LQ190 LVDS Cable Pinout..........................................125
24.5.1 Panel Pinout Sharp LQ190 ....................................................125
24.5.2 Inverter Cable Plan................................................................126
24.6 Inverter Pinout PowerSystems PS-DA0412-05 .....................126
24.6.1 Sharp LQ150 LVDS Cable Pinout..........................................127
24.6.2 Panel Pinout Sharp LQ150....................................................127
24.6.3 Inverter Cable Plan................................................................128
24.6.4 Inverter Pinout TDK CXA-0349..............................................128
24.7 Philips LB121S03-TL01 LVDS Cable Pinout .........................129
24.7.1 Panel Pinout Philips LB121S03-TL01....................................129

Copyright © 2014 congatec AG IGX1m02 11/134
24.7.2 Inverter Cable Plan................................................................130
24.7.3 Inverter Pinout Green C&C GH001HB...................................130
24.8 NEC NL6448BC33-63D LVDS Cable Pinout.........................131
24.8.1 Panel Pinout NEC NL6448BC33-63D....................................131
24.8.2 Inverter Cable Plan................................................................132
24.8.3 Inverter Pinout NEC 104PW201............................................132
24.9 Philips LM150X08 LVDS Cable Pinout ..................................133
24.9.1 Panel Pinout Philips LM150X08.............................................133
24.9.2 Inverter Cable Plan ................................................................134
24.9.3 Inverter Pinout Green C&C GH001A .....................................134

Copyright © 2014 congatec AG IGX1m02 12/134
1 Safety Instructions
Do not connect or disconnect any cables or modules to or from any onboard connectors (except for the rear I/O connectors) until the conga-IGX
is completely powered down.
Any damage caused to the conga-IGX by misuse of the onboard connectors is excluded from the standard warranty. congatec cannot be held
liable for any damage that results from incorrect use of any onboard connectors.
The system integrator is fully responsible for the usage of the appropriate connectors and cables in order to fulll the technical requirements
(electrical contact, durability, power/current levels, signal integrity etc.)
Heatsink Backplate
Caution
Insulating foil of backplate must NOT be removed, otherwise conga-IGX may be damaged due to a possible short circuit.

Copyright © 2014 congatec AG IGX1m02 13/134
2 System Memory Conguration
If you use only one memory module, then you must insert this memory module into slotA(upper slot), otherwise the conga-IGX will not operate.
Note
The conga-IGX will not operate if memory slot A is empty.

Copyright © 2014 congatec AG IGX1m02 14/134
3 Feature Overview conga-IGX
3.1 conga-IGX Reference Silkscreen
Drive Power
COM 3
LPT
Front Panel
Mouse
Keyboard
Power
COM 2
DisplayPort
PCIe X4
FAN 2
1
2
Front Panel 1 = HDD_LED+
2 = Power_LED+
3 = HDD_LED-
4 = Power_LED-
5 = Reset_Switch
DC Plug Jumper Settings1 = + DC
2 = GND
12 V max. 60 Watt
19-24 V max. 100 Watt
Plug: 2.5 / 5.5 / 11 mm
Power 1 = GND
2 = GND
3 = + DC 12 / 19-24 V
4 = + DC 12 / 19-24 V
6 = Power_Switch
7 = Reset_Switch
8 = Power_Switch
9 = Reserved
Drive Power 1 = Vcc 5 V max. 2 A
2 = GND
3 = GND
4 = +12 V max. 2 A
FAN 1
SPDIF
Front Audio
mini PCIe
mSATASATA0 SATA1
LAN
2x USB 2.0
LAN
2x USB 2.0
LVDS
Backlight
TPM GPIO Buzzer
Battery
2x USB 3.0
2x USB 2.0
LVDS
CPU
Memory Module 1 Memory Module 2
BIOS Recovery Settings
LVDS Supply Settings
USB 2.0
LVDS BL Control Settings
System Power On Settings
1
1
Fan 1 (CPU) 1 = GND
2 = 12 V PWM mode, 4..12 V 3-pin mode
3 = Sense
4 = PWM
1
Fan 2 (Chassis) 4
2
3
2
1
DC DVI-I DisplayPort
COM1 COM2
BIOS Recovery Settings
Normal Operation (default)
Normal Operation (default)
LVDS Supply Settings
LVDS BL Control Settings
System Power On Settings
Always on
BIOS Recovery / Reset to Defaults
VCC 3.3 V
(default) VCC 5 V
Analog
(default) PWM

Copyright © 2014 congatec AG IGX1m02 15/134
3.2 Block Diagram
AMD Embedded G-Series SOC
TPM Module
2x SO-DIMM DDR3
APU Plaorm
Quad Core single-chip
2nd Generaon AMD Embedded G-Series
Next generaon graphics
AMD Radeon™ HD 8000
Core #1 Core #2
low power
Core #3 Core #4
high performance
2 MB Shared L2
ASRC
Integrated I/O - HUB
High Definion Audio
ROM RAM
Int. Memory
DDR3-1600
HDA
Audio
ALC671
PCIe x4
PCIe x4 Gen2
SM
PCA
8 Bit GPIO
Super I/O #1
Super I/O #2
LPC
COM 1
PS/2
COM 2
COM 3 (int.)
Parallel
FAN1
External I/O Internal I/O
FAN2
INTRUSION
BIOS
SPI
SATA0
SATA-3
SATA-3
SATA-Switch
SATA1
mSATA
DVI-I
VGA
TDP1
DP
LTDP0
LTDP0
MUX
DP2LVDS
LVDS
4x PCIe x1
Gen2
PCIe Minicard
RTLK
RTLK
LAN1 1Gb
LAN2 1Gb
Audio IN/OUT
Buzzer
USB2.0/USB3.0
USB3.0 2 Ports
USB2.0 2 Ports
USB2.0 2 Ports
USB2.0 2 Ports
USB2.0 2 Ports
Frontpanel
SPDIF Out

Copyright © 2014 congatec AG IGX1m02 16/134
3.3 USB Structure
USB Port # Location USB Version USB Controller USB Fuse
0-3 Rear USB ports
(IO-Shield)
1.1 OHCI 1 common fuse 5V/2A
(see note below)
2.0 EHCI 1
4-7
Pin Header (4,7)
Internal “Stick” Port
(5)
Mini-PCIe (6)
1.1 OHCI 2 common fuse 5V/2A
(see note below)
2.0 EHCI 2
8-9
USB3 Header
(xHCI disabled) 1.1 OHCI 3
common fuse 5V/2A
(see note below)
2.0 EHCI 3
USB3 Header
(xHCI enabled)
1.1 xHCI2.0
3.0
Note
Specied maximum USB supply current: 0.5A/5V for each USB2.0 port; 0.9A/5V for each USB3.0 port.
Internal USB Cable Length:
USB 2.0: Board will only support USB specication compliant cables with a maximum length of 12 inches (30.5cm) for USB 2.0. The cables
must have an impedance of 90 ohms. Furthermore, the cables must have a twisted signaling pair for each individual port. That means each
port has two twisted signaling pairs and one GND cable and one power cable in one jacket with inner and outer shield. The shield of the cable
must be connected with the GND of the connector. These cables can be connected to the internal dual channel connector. For further details
see section 6 in the USB 2.0 specication.
USB 3.0: conga-IGX will only support USB 3.0 compliant cables with a maximum length of 16 inches (40.5cm) (internal USB cable to the USB
connector type A). The differential characteristic impedance for the SDP pairs is recommended to be within 90 Ω +/- 7 Ω. USB 3.0 cables have
eight primary conductors: three twisted signal pairs for USB data paths and a power pair. In addition to the twisted signal pair for USB 2.0
data path, two twisted signal pairs are used to provide the SuperSpeed data path, one for the transmit path and one for the receive path. USB
3.0 receptacles (both upstream and downstream) are backward compatible with USB 2.0 connector plugs. USB 3.0 cables and plugs are not
intended to be compatible with USB 2.0 upstream receptacles.

Copyright © 2014 congatec AG IGX1m02 17/134
3.4 conga-IGX Variants
Processor (SoC) Graphics Memory Display Options
conga-IGX/210HA
GX-210HA
Dual Core 1.0 GHz / 9W
64kB L1 Cache per Core
1MB L2 Cache shared
Radeon HD 8210E
300 MHz DDR3 / 1333 (see note below) 1 x DVI-I;
1 x DP V1.2;
1 x LVDS 24Bit Dual Ch.;
max. 2 independent displays
(DVI-I & DP or DVI & LVDS)
conga-IGX/217GA
GX-217GA
Dual Core 1.65 GHz / 15W
64kB L1 Cache per Core
1MB L2 Cache shared
Radeon HD 8280E
450 MHz DDR3 / 1600 (see note below)
conga-IGX/420CA
GX-420CA
Quad Core 2.00 GHz / 25W
64kB L1 Cache per Core
2MB L2 Cache shared
Radeon HD 8400E
600 MHz DDR3 / 1600 (see note below)
Note
1. Maximum supported memory clock.
2. For all conga-IGX variants, DDR3-1333 (CL9) or DDR3-1600 (CL11) memory modules can be installed.
3. Up to 16GB SDRAM (unbuffered, no ECC) is possible.
4. Two memory sockets available (single channel mode). Compliant with JEDEC DDR3 1.5V, DDR3L 1.35V and DDR3U 1.25V

Copyright © 2014 congatec AG IGX1m02 18/134
3.5 External Connectors conga-IGX
Audio
PS/2 Mouse & Keyboard
Dual Lan
4x USB
DisplayPort
DVI-I
2x RS232
DC Input (12V / 19-24V)

Copyright © 2014 congatec AG IGX1m02 19/134
3.6 Onboard Components
Intrusion Backlight Control
Drive Power LPT
USB 2.0 Chassis Fan
2x SO-DIMM Front panel
2x USB 2.0 COM3
Buzzer Feature / GPIO
mSATA TPM
CPU SATA1 (Gen 3)
(shared with mSATA)
mini PCIe SATA0 (Gen 3)
CPU Fan
PCIe x4 (Gen 2)
LVDS 2x24 Bit
SPDIF
DC Input
DC Input Front panel Audio
2x USB 3.0

Copyright © 2014 congatec AG IGX1m02 20/134
3.7 Heatsink Installation Notes
The following heatsinks are offered as accessories:
Passive Heatsink Passive Heatsink with
Heatpipes Active Heatsink with Fan
max. CPU TDP 9W max. CPU TDP 15W max. CPU TDP 25W
Heatsink positioning:
Backplate