Corghi Artiglio 500 User manual

Artiglio 500
Code 4-130269A - 11/2016
English Operator’s manual
Français Manuel d’utilisation

2 Artiglio 500 User Manual
Copyrighted materials. All rights reserved.
The information contained herein may be subject to modifications without prior notice.
Thank you for choosing our Tyre Changer
CORGHI
Dear Purchaser
Thank you for purchasing your Corghi Tyre Changer.
Your Tyre Changer has been designed to provide years of safe and dependable service,
as long as it is used and maintained in accordance with the instructions provided in this
manual.
All persons who will use and/or maintain this Tyre Changer must read, understand and
follow all warnings and instructions provided in this manual, and be properly trained.
This Owner’s Manual should be considered an internal part of your Tyre Changer and
should remain with the Tyre Changer. However, nothing in this manual, and none of the
devices installed on the Tyre Changer, substitute for proper training, careful operation,
good judgement and safe work practices.
Always be sure that your Tyre Changer is in optimum working order. If you suspect that
anything is not working properly, or that a dangerous situation may exist, immediately
shut down the Tyre Changer and remedy any condition before you proceed.
If you have any questions concerning the proper use or maintenance of your Tyre Changer,
please call your authorized Corghi representative.
Sincerely,
Corghi SpA
OWNER INFORMATION
Owner
Name_______________________________________________________________
Owner
Address_____________________________________________________________
Model
Number_____________________________________________________________
Serial
Number_____________________________________________________________
Date
Purchased___________________________________________________________
Date
Installed ____________________________________________________________
Service and Parts
Representative_______________________________________________________
Phone
Number_____________________________________________________________
Sales
Representative_______________________________________________________
Phone
Number_____________________________________________________________

Artiglio 500 User Manual 3
UK
TRAINING CHECKLIST
Trained Declined
Safety Precautions
Warning and Caution Labels
Pinch Points and Other Potential Hazards
Safe Operating Procedures
Maintenance and Performance Checks
Mounting Head Inspection
Adjustment and Lubrication
Clamping
Steel / Alloy Wheels
Reverse Drop Centre Wheels
Close Centre Wheels
Bead Breaking
Standard Wheels
Low Profile Wheels
Demounting
Standard Wheels with Bead Lever and Plastic Sleeve Protector
Full Seating of Mount/Demount Head to Prevent Head Failure
Bead Lubrication During Removal of Low Profile Tyres
Reverse Drop Centre Wheels
Mounting
Standard Wheels
Mounting of Stiff, Low Profile Tyres
Reverse Drop Centre Wheels
Proper Bead Lubrication for Mounting Protection
Accessories
Instructions for the Correct Use of Accessories
Bead Sealing and Seating
Inflation
Safety Precautions
Lubrication and Removal of Valve Core
Bead Sealing and Seating

4 Artiglio 500 User Manual
Individuals and Dates Trained
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________

Artiglio 500 User Manual 5
UK
TABLE OF CONTENTS
1. GETTING STARTED .........................................................................7
1.1 INTRODUCTION ..............................................................................................7
1.1.a. Purpose of the manual .......................................................................................7
1.2 FOR YOUR SAFETY .........................................................................................7
1.2.a. General warning and instructions .....................................................................8
1.2.b. Decal placement...............................................................................................11
1.2.c. Electrical and pneumatic connections............................................................15
1.2.d. Technical data ...................................................................................................16
1.2.e. Air pressures......................................................................................................17
1.3 SPECIAL RIM/TYRE CONSIDERATIONS......................................................18
1.4 INTENDED USE OF THE MACHINE............................................................18
1.5 EMPLOYEE TRAINING..................................................................................18
1.6 PRE-USE CHECKS.........................................................................................18
1.7 DURING USE..................................................................................................19
2. TRANSPORT, STORAGE AND HANDLING..................................19
2.1 UNPACKING...................................................................................................20
3. HOISTING/HANDLING..................................................................20
3.1 INSTALLATION ..............................................................................................20
3.2 INSTALLATION CLEARANCES.....................................................................23
3.3 FIRST INSTALLATION ...................................................................................24
4. ARTIGLIO A 500 DESCRIPTION....................................................25
4.1 OPERATOR POSITION...................................................................................26
4.2 OVERALL DIMENSIONS...............................................................................26
4.3 EQUIPMENT COMPONENTS (MAIN WORKING ELEMENTS OF THE MACHINE). 27
4.4 CONTROLS.....................................................................................................28
4.4.a. Operating console.............................................................................................29
4.4.b. Swing control arm and pressure gauge panel...............................................30
4.4.c. Pedal unit ..........................................................................................................30
4.4.d. Wheel lifter control pedal ...............................................................................30
4.4.e. Tool head arm control handle ........................................................................31
4.5 OPTIONAL ACCESSORIES............................................................................31
5. BASIC PROCEDURE - USE ............................................................31
5.1 PRELIMINARY CHECKS................................................................................32
5.2 LOADING AND CLAMPING THE WHEEL...................................................33
5.3 DEFLATING THE TYRE.................................................................................36
5.4 BEAD BREAKING ..........................................................................................36
5.5 DEMOUNTING...............................................................................................40
5.6 MOUNTING....................................................................................................48
5.7 EXTRAORDINARY MOUNTING PROCEDURE............................................51
5.8 APPROVED UHP AND RUN FLAT TYRE DEMOUNTING AND MOUNTING
PROCEDURE........................................................................................................51

6 Artiglio 500 User Manual
5.9 TYRE INFLATION...........................................................................................52
5.9.a. Safety indication ...............................................................................................52
5.9.b. Inflating tyres.....................................................................................................53
5.9.c. Special procedure.............................................................................................55
5.10 UNCLAMPING AND UNLOADING THE WHEEL........................................ 57
6. TROUBLESHOOTING ....................................................................58
7. MAINTENANCE..............................................................................61
8. INFORMATION ABOUT SCRAPPING............................................63
9. ENVIRONMENTAL INFORMATION..............................................63
10. INFORMATION AND WARNINGS ABOUT HYDRAULIC FLUID. 64
11. FIREFIGHTING MEANS USABLE ...............................................65
12. GLOSSARY ....................................................................................66
13. ELECTRIC DIAGRAM ...................................................................69
14. GENERAL PNEUMATIC SYSTEM DIAGRAM.............................70
TABLE FOR USING CENTRING AND CLAMPING ACCESSORIES
ACCORDING TO RIM TYPE .....................................................................................72

Artiglio 500 User Manual 7
UK
1. GETTING STARTED
1.1 INTRODUCTION
1.1.a. PURPOSE OF THE MANUAL
The purpose of this manual is to provide the instructions necessary for optimum operation,
use and maintenance of your machine. If you sell this machine, please deliver this manual
to the new owner. In addition, so we can contact our customers with any necessary safety
information, please ask the new owner to complete and return to Corghi the change of
ownership form attached to the previous page of this manual. Alternatively, the new owner
can send an email to [email protected].
This manual presumes that the technician has a thorough understanding of rim and tyre
identification and service. He/she must also have a thorough knowledge of the operation
and safety features of all associated tools (such as the rack, lift, or floor jack) being utilized,
and have the proper hand and power tools necessary to work in a safe manner.
The first section provides the basic information to safely operate the ARTIGLIO 500 tyre
changer family. The following sections contain detailed information about equipment, pro-
cedures, and maintenance. “Italics” are used to refer to specific parts of this manual that
provide additional information or explanation.
Thesereferencesshouldbereadforadditionalinformationtothe instructionsbeingpresented.
The owner of the tyre changer is solely responsible for enforcing safety procedures and
arranging technical training. The tyre changer is to be operated only by a qualified and
trained technician. Maintaining records of personnel trained is solely the responsibility of
the owner or management.
The ARTIGLIO 500 tyre changer family is intended for mounting, demounting, and inflating
tyres of lightweight vehicles (cars, not trucks or motorcycles) with maximum dimensions of
47 inches in diameter and 16 inches in width.
Copies of this manual and of the documents accompanying the machine may be obtained
from Corghi by specifying the type of machine and its serial number.
NOTICE: Design details are subject to change. Some illustrations may vary slightly in ap-
pearance from the machine you have.
1.2 FOR YOUR SAFETY
HAZARD DEFINITIONS
These symbols identify situations that could be detrimental to your safety and/or cause
equipment damage.
DANGER: Indicates an imminently hazardous situation which, if not avoided, will
result in death or serious injury.
DANGER

8 Artiglio 500 User Manual
WARNING: Indicates a potentially hazardous situation which, if not avoided, could
result in death or serious injury.
WARNING
CAUTION: Indicates a potentially hazardous situation which, if not avoided, may
result in minor or moderate injury.
CAUTION
NOTICE: Used without the safety alert symbol, indicates a potentially hazardous
situation, which, if not avoided, may result in property damage.
NOTICE
1.2.a. GENERAL WARNING AND INSTRUCTIONS
Avoid Personal Injury. Carefully read, understand and follow the warnings and instructions given in this manual.
This manual is an essential part of the product. Keep it with the machine in a safe place for future reference.
WARNING
1. If the use and maintenance procedures provided in this manual are not properly
performed, or the other instructions in this manual are not followed, an accident could
occur. Throughout this manual reference is made that “an accident” could occur. Any
accident could cause you or a bystander to sustain severe personal injury or death, or
result in property damage.
2. Overinflated tyres can explode, producing hazardous flying debris that may result in
an accident.
3. Tyres and rims that are not the same diameter are “mismatched.” Never attempt to
mount or inflate any tyre and rim that are mismatched. For example, never mount a
16.5” tyre on a 16” rim and vice versa. This is very dangerous. A mismatched tyre and
rim could explode, resulting in an accident.

Artiglio 500 User Manual 9
UK
4. Never exceed the bead setting pressure provided by the
tyre manufacturer, as stated on the sidewall of the tyre.
Carefully monitor the gauge on the air hose.
5. If tires being mounted require more than the tire ma-
nufacturer’s maximum bead seating pressure and , the
wheel should be removed from the tire changer, placed
in an inflation cage, and inflated per manufacturer’s in-
structions
6. The use of inflation devices (e.g. guns) connected to
power sources outside of the machine is not permitted
7. Never place your head or any part of your body over a tyre during the inflation process
or when attempting to seat beads. This machine is not intended to be a restraining
device for exploding tyres, tubes or rims.
8. Always stand back from the tyre changer when inflating, never lean over.
An exploding tyre and rim may be propelled upward and outward with enough force to cause
serious injury or death.
Never mount any tyre unless the tyre size (molded into the sidewall) matches the rim size
(stamped into the rim) exactly or if the rim or tyre are defective.
Never exceed the tyre pressure recommended by the tyre manufacturer.
This tyre changer is not a safety device and will not restrain exploding tyres and rims. Keep
the area clear of bystanders.
DANGER
9. Crushing Hazard. Moving Parts Present. Contact with moving parts
could result in an accident.
• Only one operator may work with the machine at a time.
• Keep all bystanders clear of tyre changer.
• Keep hands and ngers clear of rim edge during the demounting
and mounting process.
• Keep hands and ngers clear of mount/demount head during
operation.
• Keep hands, feet and other body parts away from moving parts.
• Do not use tools other than those supplied with tyre changer.
• Use proper tyre lubricate to prevent tyre binding.
• Pay attention while moving tyre/rim or lever.
Avoid Personal Injury. Carefully read, understand and follow the warnings and instructions given in this manual.
This manual is an essential part of the product. Keep it with the machine in a safe place for future reference.
WARNING

10 Artiglio 500 User Manual
10. Electric Shock Hazard.
• Never hose down or power wash electric tyre changers.
• Do not operate the machine with a damaged power cord
• If an extension cord is necessary, a cord with a current rating equal to or
greater than that of the machine must be used. Cords rated for less current
than the machine can overheat, resulting in a fire.
• Care should be taken to arrange the cord so that it will not be tripped
over or pulled.
11. Risk of Eye Injury. Flying debris, dirt and fluids may be discharged dur-
ing bead seating and the inflation process. Remove any debris from the
tyre tread and wheel surfaces. Wear OSHA, CE or other approved safety
glasses during mount and demount procedures.
12. Always inspect the machine carefully before using it. Missing, broken,
or worn equipment (including warning stickers) must be repaired or replaced prior to operation.
13. Never leave nuts, bolts, tools or other equipment on the machine. They may become trapped
between moving parts and cause a malfunction.
14. NEVER install or inflate tyres that are cut, damaged, rotten or worn. NEVER install a tyre on a
cracked, bent, rusted, worn, deformed or damaged rim.
15. If a tyre becomes damaged during the mounting process, do not attempt to finish mounting.
Remove from the service area and properly mark the tyre as damaged.
16. To inflate tyres, use short bursts while carefully monitoring the pressure, tyre, rim and bead.
NEVER exceed the tyre manufacturer’s pressure limits.
17. This equipment has internal arcing or sparking parts which should not be exposed to flammable
vapours (gasoline, paint thinners, solvents, etc.). This machine should not
be located in a recessed area or below floor level.
18.Neveroperatethemachine if youareundertheeffectsof alcohol, medica-
tions and/or drugs. If you are taking prescription or over the counter medica-
tion, you must consult a medical professional regarding any side effects of
the medication that could hinder your ability to operate the machine safely.
19. Always use OSHA, CE or other approved and mandated Personal Protec-
tive Equipment (PPE) during use of the machine. See your supervisor for
more instructions.
20. Remove jewellery, watches, loose clothing, ties and restrain long hair
before using the machine.
21. Wear non-slip safety footwear when operating the tyre changer.
22. Wear proper back support and employ a proper lifting technique when
placing, moving, lifting or removing wheels from the tyre changer.

Artiglio 500 User Manual 11
UK
23. This machine may only be used, maintained or repaired by properly trained employees of
your company. Repairs should only be performed by qualified personnel. Your CORGHI service
representative is the most qualified person. The employer is responsible for determining if an em-
ployee is qualified to safely make any repairs to the machine should repair be attempted by users.
24. The user should understand all warning decals affixed to this equipment before operating.
25. Lock the rim on the turntable during inflation.
1.2.b. DECAL PLACEMENT
No. Part Number Drawing Description
1
4-103720 DECAL, ARM MOVEMENTS
2
446429 DECAL,MAX.INLETPRESSURE
16 BAR
3
446442 DECAL, WARNING UNDER
PRESSURE TANK
4
4-108711 DECAL, ARTIGLIO 500
5
4-113355 DECAL, FILTER
6
418135 DECAL, DIRECTION OF ROTA-
TION
7
4-103881 DECAL, CORGHI LOGO
8
4-104346 DECAL, WHEEL LIFTER CON-
TROL
9
446436 DECAL, INFLATION VALVE

12 Artiglio 500 User Manual
No. Part Number Drawing Description
10
446435 DECAL, HAND CRUSHING
HAZARD
11
4-104920 DECAL, ARM MOVEMENT
HAZARD
12
462081A DECAL, HAND CRUSHING
HAZARD
13
446388 DECAL, CORRECT FEEDING
NETWORK
14 462778 DECAL, SAFETY INSTRUC-
TIONS
15
461933 DECAL, INFLATING PEDAL
16
461932 DECAL, TURNTABLE ROTA-
TION PEDAL
17
462080 DECAL, ACOUSTIC AND VISU-
AL PROTECTION
18
461930 DECAL, FOOT CRUSHING
HAZARD
19
425211 DECAL, ELECTRIC HAZARD
20
432740 DECAL, EXPLOSION HAZARD
21
4-108591 DECAL, CONSOLLE CON-
TROLS

Artiglio 500 User Manual 13
UK
No. Part Number Drawing Description
22
42015 - Correggio (RE) Italy
ISO9001
Code
Serial N.
X-XXXXXXXX/XX - XX
XXXXXXXXX
QUAL. SYS. CERTIFIED
ANNO DI COSTRUZIONE /
MANUFACTURED
Mod.
V
A
kW
Hz
Ph
bar7psi
Port.max
DECAL, MODEL SERIAL NUM-
BER
23
4-121505 DECAL, WARNING.
1
5
6
7
8
9
11
12
14
15
16
10
18
12
2
3
4
22 21
17
12
11
20
23
DANGER WARNING DECALS
part nr 462081. Crushing Hazard.

14 Artiglio 500 User Manual
part nr 461930. Crushing hazard.
part nr 446435. Crushing hazard.
part nr 446442. EXPLOSION HAZARD. Do not puncture.
Danger - pressurised container.
part nr 425211A. Risk of electrical shock.
part nr 4-104920. Crushing hazard.
Only one operator may operate and use the machine.
part nr 462778. Safety instructions.
part nr 425083. Earth ground terminal.
part nr 432740. Explosion hazard.

Artiglio 500 User Manual 15
UK
part nr 4-121505. Warning. Do not use below floor level.
1.2.c. ELECTRICAL AND PNEUMATIC
CONNECTIONS
The dimensions of the electric hook-up
used must be suitably sized in relation to:
• the electric power absorbed by the ma-
chine, indicated on its data plate (Fig. 1);
• the distance between the machine and
the power supply hook-up point, so that
voltage drops under full load do not ex-
ceed 4% (10% during start-up) compared with
the rated voltage specified on the data plate.
- The operator must:
• t a power plug on the power supply lead in
compliancewiththerelevantsafetystandards;
• connect the machine to its own electrical con-
nection - A, Fig. 2 - and fit a differential safety
circuit-breaker with 30 mA residual current;
• t fuses to protect the power supply line,
rated as indicated on the general wiring dia-
gram in this manual;
• connect the machine to an industrial socket;
the machine must not be connected to do-
mestic sockets.
FOR CANADIAN MARKET ONLY:
• The machine must be hard wired connec-
tion and fit a differential, 20A maximum,
safety circuit-breaker with 30 mA residual
corrent.
• Fit a fuse to protect the power supply line,
rated as indicated on the general wiring
diagram in this manual.
An effective grounding connection is essential for correct operation of the machine.
NOTICE
Make sure the available pressure and the rendered capacity of the compressed air system
arecompatiblewiththoserequiredfor correct machine operation-seethe“TechnicalData”
section. For correct machine operation, the compressed air supply line must provide a
A
2
42015 - Correggio (RE) Italy
ISO9001
Code
Serial N.
X-XXXXXXXX/XX - XX
XXXXXXXXX
QUAL. SYS. CERTIFIED
ANNO DI COSTRUZIONE /
MANUFACTURED
Mod.
V
A
kW
Hz
Ph
bar7psi
Port.max
1

16 Artiglio 500 User Manual
pressure range from no less than 8.5 bar to no more than 16 bar and guarantee an air flow
rate greater than the average consumption of the machine, which is equal to 120 Nl/min.
For correct equipment operation, the air produced must be suitably treated (not
above 5/4/4 according to ISO 8573-1)
NOTICE
Check that the Lubricator unit B fig. 2a contains air
lubricating oil; top up if necessary. Use SAE20 oil.
The customer must provide an air cut-off valve upstre-
am of the air treatment and regulator device supplied
with the machine.
Before operating any command, follow the
instructions affixed to the machine.
See also Section 3.3, “FIRST INSTALLATION”
1.2.d TECHNICAL DATA
- Tyre types processed ................................. conventional runflat with reinforced sidewall
and/or with internal support
- Wheel dimension range:
• rim diameter ................................................................................................ from 12” to 32”
• maximum tyre diameter .............................................................................. 1200 mm (47”)
• maximum tyre width .................................................... 15” (from wheel support surface)
- Turntable:
• rest..............................................................................................................................flanged
• centring..................................................................................................................... on cone
• clamping....................................................................................................mechanical-manual
• drive system...............................................................................2-speed motor-inverter unit
WARNING
B
2a

Artiglio 500 User Manual 17
UK
• rotation torque............................................................................................................ 1100 Nm
• rotation speed .......................................................................................................... 7 - 18 rpm
- Bead Breaker Unit:
• bead breaking cylinder force .........................................................................................7600N
- Wheel lift:
• lifting capacity................................................................................................................... 85 Kg
- Power supply:
• electric 1 Phase............................................................................... 230V-0.75 kW 50Hz/60 Hz
• electrical 1 Phase (alternative)..................................................... 110V-0.75 kW 50Hz/60 Hz
• pneumatic operating pressure ..................................................................................8÷10 bar
- Weight.......................................................................................................380 kg (with wheel lift)
- Noise level
• Weighted noise level A (LpA) in working position ..............................................< 70 dB (A
The stated noise levels are emission levels and do not necessarily represent safe operating
levels. Although there is a relationship between emission levels and exposure levels, this
cannot be used reliably to establish whether or not further precautions are necessary. The
factors which determine the level of exposure to which the operator is subjected include the
duration of the exposure, the characteristics of the workplace, other sources of noise, etc. The
permitted exposure levels may also vary from country to country. However, this information
will enable the machine’s user to make a more accurate evaluation of the hazard and risk.
1.2.e. AIR PRESSURES
The machine is equipped with an internal pressure limiting valve to minimize the risk of
over inflating the tyre.
•EXPLOSION HAZARD
•Never exceed the tyre pressure recommended by the tyre
manufacturer. Never mismatch tyre size and rim size.
•Avoid personal injury or death
DANGER
1. Never exceed these pressure limitations:
• Supply line pressure (from compressor) is 220 psi (15 bar).
• Operating pressure (gauge on regulator) is 145 psi (10 bar).
Bead setting pressure (gauge on hose) is the tyre manufacturer’s maximum pressure as
stated on the sidewall of the tyre
2. Activate air inflation jets only when sealing the bead.
3. Bleed air pressure system before disconnecting supply line or other pneumatic compo-
nents. Air is stored in a reservoir for operation of inflation jets.
4. Only activate the air inflation jets if the rim securing device is locked in place and the tyre
is properly clamped (when possible).

18 Artiglio 500 User Manual
1.3. SPECIAL RIM/TYRE CONSIDERATIONS
Wheels equipped with low tyre pressure sensors or special tyre and rim designs may
require special procedures. Consult wheels and tyre manufacturers' service manuals.
NOTICE
1.4. INTENDED USE OF THE MACHINE
This machine must be used only to remove and replace an automotive tyre on an automo-
tive rim, using the tools with which it is equipped. Any other use is improper and can result
in an accident.
The machine can not work on motorcycle wheels.
1.5. EMPLOYEE TRAINING
1. The employer is obligated to provide a programme to train all employees who service rim
wheels in the hazards involved in servicing those rim wheels and the safety procedures to be
followed. Service or servicing means the mounting and demounting of rim wheels, and related
activities such as inflating, deflating, installing, removing and handling.
• The employer shall insure that no employee services any rim wheel unless the employee
has been trained and instructed in correct procedures of servicing the type of wheel being
serviced, and in safe operating procedures.
• Information to be used in the training programme shall include, at a minimum, the applicable
information contained in this manual.
2. The employer shall ensure that each employee demonstrates and maintains the ability to
service rim wheels safely, including performance of the following tasks:
• Demounting tyres (including deation).
• Inspecting and identifying rim wheel components.
• Mounting tyres.
• Using any restraining device, cage, barrier, or other installation.
• Handling rim wheels.
• Inating the tyre.
• Understanding the necessity to stand back from the tyre changer during tyre ination and
during inspection of the rim wheel following inflation, never leaning over.
• Installing and removing rim wheels.
3. The employer shall evaluate each employee’s ability to perform these tasks and to service
rim wheels safely, and shall provide additional training as necessary to assure that each em-
ployee maintains his or her proficiency.
1.6. PRE-USE CHECKS
Before beginning work, carefully check that all components of the machine, especially rub-
ber or plastic parts, are in place, in good condition and working properly. If the inspection

Artiglio 500 User Manual 19
UK
reveals any damage or excessive wear, no matter how slight, immediately replace or repair
the component.
1.7. DURING USE
Intheevent you hearanystrange noise orfeelunusual vibration, ifacomponent or systemisnot
operating properly, or if there is anything unusual at all, stop using the machine immediately.
• Identify the cause and take any necessary remedial action.
• Contact your supervisor if necessary.
Never allow any bystander to be within 20 feet of the machine during operation.
To stop the machine in an emergency:
• disconnect the power supply plug;
• cut off the compressed air supply network by disconnecting the shut-off valve (snap coupling).
2. TRANSPORT, STORAGE AND HANDLING
Conditions for transporting the machine
The tyre changer must be transported in its original packing and stowed in the position shown
on the packing itself.
- Packing dimensions:
• width ............................................................................................................................... 1543 mm
• depth .............................................................................................................................. 1140 mm
• height .............................................................................................................................. 1890 mm
- Weight of wooden packing:
• STD version ........................................................................................................................ kg 396
• TI version ............................................................................................................................ kg 410
Machine storage and shipping specifications
Temperature: -25° - +55°C.
Do not stack other goods on top of the packing or damage may result.
NOTICE
Handling
To move the packing, insert the tines of a fork-lift
truck into the slots on the base of the packing itself
(pallet) (Fig.3).
Before moving the machine, refer to the HOISTING/
HANDLING section.
3

20 Artiglio 500 User Manual
Keep the original packing in good conditions to be used if the equipment has to be
shipped in the future.
NOTICE
2.1. UNPACKING
Remove the upper part of the packing and make sure the machine has not been damaged
during transportation.
3. HOISTING/HANDLING
Take the utmost care when unpacking, assembling, hoisting and installing the ma-
chine as described below.
Failure to observe these instructions can damage the machine and compromise the
operator’s safety.
WARNING
Before removing the machine from the pallet, make sure the items shown below
have been removed from the pallet .
NOTICE
3.1. INSTALLATION
- Remove the top part of the
cardboard packaging. Make
surethatthemachinehasnot
beendamagedintransit,and
identify the points at which
it is anchored to the pallet
(fig. 4), ready to remove the
machine.
- The machine comprises five
main sections (fig.5):
1. Body with pedal unit and
turntable.
2.Columnwithbeadbreaking
unit and tool arm.
3. Air tank (T.I. version only).
4. Wheel lift.
5. Bead presser (Optional).
6.Accessoriesbox(seeFig.4).
6
4