Corghi Artiglio 5000 User manual

Artiglio 5000
Codice 4-122510 - 07/2017
Italiano Manuale d’uso 3
English Operator’s manual 77
Français Manuel d’utilisation 151
Deutsch Betriebsanleitung 225
Español Manual de uso 299

Artiglio 5000 Operator Manual 77
EN
Copyrighted material. All rights reserved.
The information contained herein may be subject to modifications without prior notice.
Thank you for choosing our tyre changer
CORGHI
Dear Customer
Thank you for purchasing your Corghi Tyre Changer.
Your Tyre Changer has been designed to provide years of safe and dependable service,
as long as it is used and maintained in accordance with the instructions provided in this
manual.
Everyone who will use and/or perform maintenance on the tyre changer must read,
understand and observe all the warnings and instructions provided in this manual, in
addition to being properly trained.
This instruction manual must be considered an integral part of the tyre changer and
kept together with it. However, no information contained in this manual and no device
installed on the tyre changer can replace suitable training, correct operation and careful
evaluation of procedures for working safely.
Always make sure that the tyre changer is in optimal operating conditions. If any malfunc-
tions or probable situations of danger are observed, immediately stop the tyre changer
and resolve the conditions before continuing.
For any question related to the correct tyre changer use or maintenance, contact your
local official Corghi dealer.
Sincerely,
Corghi SpA
USER INFORMATION
User
Name_______________________________________________________________
User
Address_____________________________________________________________
Model
number_____________________________________________________________
Serial
number_____________________________________________________________
Date of
purchase___________________________________________________________
Date of
installation ____________________________________________________________
Service and spare parts
manager_______________________________________________________
Phone
number_____________________________________________________________
Sales
Representative_______________________________________________________
Phone
number_____________________________________________________________

78 Artiglio 5000 Operator Manual
TRAINING CHECK
Qualified Rejected
Safety Precautions
Warning and caution labels
High risk areas and other potential hazards
Operative safety procedures
Maintenance and Performance Checks
Head mounting inspection
Adjustment and lubrication
Maintenance and instruction messages
Clamping
Steel/alloy rims
Reverse rims
Closed rims
Bead Breaking
Standard wheels
Low profile wheels
Demounting procedure
Bead lubrication when removing the low profile tyres
Reverse rims
Mounting
Standard wheels
Mounting of stiff, low profile tyres
Wheel with reverse rim
Bead lubrication for proper mounting
WDK procedure
Accessories
Instructions for correct use of the accessories
Inflatron user instructions (optional)
Inflation
Safety measures
Lubrication and removal of the valve insert
Tubeless tyre inflation

Artiglio 5000 Operator Manual 79
EN
Individuals and Dates Trained
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________

80 Artiglio 5000 Operator Manual
Sommario
1. GETTING STARTED ................................................................................ 82
1.1 INTRODUCTION ...........................................................................................82
1.1.A. PURPOSE OF THE MANUAL .........................................................................82
1.2 FOR YOUR SAFETY ......................................................................................82
1.2.A. GENERAL WARNING AND INSTRUCTIONS ................................................83
1.2.B. DECAL PLACEMENT ......................................................................................86
1.2.C. ELECTRICAL AND PNEUMATIC CONNECTIONS .........................................90
1.2.D TECHNICAL DATA ............................................................................................91
1.2.E. AIR PRESSURE .................................................................................................92
1.3. ADDITIONAL RIM/TYRE INFORMATION ..................................................93
1.4. INTENDED MACHINE USE ........................................................................93
1.6. PRELIMINARY CHECKS..............................................................................94
1.7. DURING USE................................................................................................94
2. TRANSPORT, STORAGE AND HANDLING........................................... 95
3. ASSEMBLY/HANDLING .......................................................................... 96
3.1. HOISTING/HANDLING ...............................................................................96
3.2. INSTALLATION ............................................................................................97
5. DESCRIPTION OF ARTIGLIO 5000 ........................................................ 98
5.1. OPERATOR POSITION.................................................................................99
5.2. OVERALL DIMENSIONS.............................................................................99
5.3. EQUIPMENT COMPONENTS (MAIN WORKING OPERATING ELEMENTS
OF THE MACHINE) ..........................................................................................100
5.4. CONTROLS.................................................................................................103
5.4.A. CONTROL CONSOLE (FIG. 12).....................................................................103
5.4.B. PEDAL UNIT (FIG. 13) ...................................................................................104
5.4.C. WHEEL LIFTER PEDAL UNIT (OPTIONAL) FIG. 14....................................105
5.4.D. PRESSURE GAUGE WITH
DEFLATE BUTTON (FIG. 15) ...................................................................................105
6. BASIC PROCEDURES - USE ................................................................. 106
6.1. PRELIMINARY CHECKS............................................................................107
6.2. DECIDING FROM WHICH SIDE OF THE WHEEL THE TYRE MUST BE
DEMOUNTED ...................................................................................................107
6.3. WHEEL LOADING .....................................................................................108
6.4. CLAMPING THE WHEEL ON THE TURNTABLE ....................................110
6.5. TYRE DEFLATION ....................................................................................112
6.6. BEAD BREAKING ......................................................................................112
6.7. DEMOUNTING PROCEDURE...................................................................115
6.8. MOUNTING................................................................................................118
TRANSLATION FROM ORIGINAL LANGUAGE (ITALIAN)

Artiglio 5000 Operator Manual 81
EN
6.9. APPROVED UHP and RUN FLAT TYRE DEMOUNTING AND MOUNTING
PROCEDURE ....................................................................................................121
6.10. TYRE INFLATION.....................................................................................122
6.10.A. SAFETY REGULATIONS ..............................................................................122
6.10.B. TYRE INFLATION .........................................................................................123
6.10.C. SPECIAL PROCEDURE (TI VERSION) ........................................................124
6.11 UNCLAMPING THE WHEEL AND UNLOADING...................................126
6.11.A. WHEEL UNCLAMPING ................................................................................126
6.11.B WHEEL UNLOADING ...................................................................................127
7. MAINTENANCE ..................................................................................... 127
Scheduled maintenance: ................................................................................128
8. INFORMATION ABOUT SCRAPPING .................................................. 130
9. ENVIRONMENTAL INFORMATION..................................................... 130
10.INFORMATION AND WARNINGS
ABOUT OIL .......................................................................................... 131
11.INFORMATION AND WARNINGS
ABOUT TYRE LUBRICATING FLUID .................................................. 131
12. RECOMMENDED FIRE EXTINGUISHING EQUIPMENT................. 132
13. GLOSSARY ........................................................................................... 133
TABLE FOR USING CENTRING AND CLAMPING
ACCESSORIES ACCORDING TO RIM TYPE ...................................... 137
WIRING DIAGRAM .................................................................................... 145
PNEUMATIC DIAGRAM ............................................................................ 146

82 Artiglio 5000 Operator Manual
1. GETTING STARTED
1.1 INTRODUCTION
1.1.a. PURPOSE OF THE MANUAL
The purpose of this manual is to provide the instructions necessary for optimum operation,
use and maintenance of your machine. If you sell this machine, please deliver this manual
to the new owner. Furthermore, ask the new owner to fill out the ownership transfer module
attached to the previous page in the manual and send it to Corghi, so that Corghi will be
able to provide the customer with all necessary safety information. Alternatively, the new
owner can send an email to [email protected].
Thismanual assumesthat thetechnicianshavefull understandingregardingtheidentification
and maintenance of rims and tyres. They must also have thorough knowledge regarding the
operation and safety features of the relative tools (such as the rack, lift or the jack) that are
used, as well as the manual or electric tools required to perform the work safely.
The first section provides basic information for the safe operation of the Artiglio 5000 tyre
changer family. The following sections contain detailed information regarding equipment,
procedures and maintenance. “Italics” are used to refer to specific parts of this manual that
provide additional information or explanation.
Thesereferencesshouldbereadforadditionalinformationtotheinstructionsbeingpresented.
The owner of the tyre changer is the only person responsible for the observance of the
safety procedures and the organisation of technical training. The tyre changer must only be
used by qualified, specifically trained technicians. The owner or management is exclusively
responsible for storing the documentation relative to qualified personnel.
The Artiglio 5000 family of tyre changers is designed and manufactured for mounting,
demounting and inflating tyres for light vehicles (passenger cars - not intended for use
for trucks or motorcycles) with a maximum external diameter of 47 inches and a maximum
width of 15 inches.
Copies of this manual and of the documents accompanying the machine may be obtained
from Corghi by specifying the type of machine and its serial number.
NOTICE: Design details are subject to change. Some illustrations may vary slightly in ap-
pearance from the machine you have.”
1.2 FOR YOUR SAFETY
HAZARD DEFINITIONS
These symbols identify situations that could be harmful to the safety of personnel and/
or cause damage to the equipment.

Artiglio 5000 Operator Manual 83
EN
DANGER: Indicates an imminently hazardous situation which, if not
avoided, will result in death or serious injury.
DANGER
WARNING: Indicates a potentially hazardous situation which, if not
avoided, could result in death or serious injury.
CAUTION!
CAUTION: Indicates a potentially hazardous situation which, if not
avoided, may result in minor or moderate injury.
WARNING
NOTICE: Used without the safety alert symbol indicates potentially
hazardous situation, which, if not avoided, may result in property
damage.
CAUTION!
1.2.a. GENERAL WARNING AND INSTRUCTIONS
Avoid Personal Injury. Carefully read, understand and follow the warnings and
instructions given in this manual. This manual is an essential part of the product.
Keep it with the machine in a safe place for future reference.
CAUTION!
1. If the maintenance procedures described in this manual are not executed correctly, or if
other instructions in the manual are not observed, accidents could occur. This manual makes
continuous reference to the possibility that accidents can occur. Any accident could cause
serious or fatal injuries to the operator or people nearby, or cause material damage.

84 Artiglio 5000 Operator Manual
2. Overinflated tyres can explode, producing hazardous flying debris that may result in
an accident.
3. Tyres and rims that do not have the same diameter do not correspond. Never attempt
to mount or inflate tyres and rims that do not correspond. For example, never mount
a 16.5” tyre on a 16” rim, or vice versa. It is very dangerous. Tyres and rims that do not
correspond could explode, causing accidents.
4. Never exceed the inflation pressure for the tyre indicated by the manufacturer on the
side of the tyre itself. Carefully check that the air hose
is well inserted in the valve
5. Never bring your head or other body parts close to a
tyre during inflation or bead insertion operations. This
machine is not a safety device against the possible ex-
plosion risk of tyres, air chambers or rims.
6. Maintain a suitable distance from the tyre changer while
inflating. Do not approach it.
A bursting tyre can cause projections of its parts in surrounding areas with a force
sufficient to cause serious injury or death.
Do not mount a tyre if its dimensions (indicated on the side) do not correspond
exactly with the rim dimensions (printed inside the rim) or if the rim or the tyre
are defective or damaged.
Never exceed the pressure recommended by the tyre manufacturer.
The tyre changer is not a safety device and does not prevent tyres and rims from
exploding. Keep other people at a distance
DANGER
7. Crushing Hazard. Moving Parts Present. Contact with moving parts
could result in an accident.
The machine may only be used by one operator at a time.
s+EEPALLBYSTANDERSCLEAROFTIRECHANGERs+EEPHANDSANDlNGERSCLEAROFRIMEDGEDURINGTHEDEMOUNTINGand mounting process.
s+EEPHANDSANDlNGERSCLEAROFMOUNTDEMOUNTHEADDURINGoperation.
s+EEPHANDSANDOTHERBODYPARTSAWAYFROMMOVINGPARTSs$ONOTUSETOOLSOTHERTHANTHOSESUPPLIEDWITHTYRECHANGERs5SELUBRICANTTHATISSPECIlCFORTYRESINORDERTOPREVENTTYREseizure.
s0AYATTENTIONWHILEHANDLINGTHERIMANDTYREANDWHILEUSINGTHElever
8. Electric Shock Hazard.
s$ONOTCLEANTHEELECTRICPARTSWITHWATERORHIGHPRESSUREAIRJETS

Artiglio 5000 Operator Manual 85
EN
s$ONOTOPERATEMACHINEWITHADAMAGEDPOWERCORDs)FANEXTENSIONISNECESSARYUSEACABLEWITHNOMINALFEATURESEQUALTOORGREATERthan those for the machine. Cables with nominal features that are lower to those of
the machine could overheat and cause a fire.
sMake sure that the cable is positioned so that no one will trip over it and it cannot be
pulled.
9. Hazard of eye injuries. During the bead insertion and inflation phase, debris, dust and
fluids could be projected into the air. Remove any debris present in the tread of the
tyre and on the tyre surface. Wear protective goggles with OSHA, CE approval or other
certified devices during all work phases.
10. Always inspect the machine carefully before using it. Missing,
broken, or worn equipment (including warning stickers) must be
repaired or replaced prior to operation.
11. Never leave nuts, bolts, tools or other materials on the machine.
They could remain trapped in moving parts and cause malfunctions
or be projected out of the machine.
12. DO NOT install or inflate tyres that are cut, damaged, decayed or worn. DO NOT install
tyres on damaged, bent, rusted, worn or deformed rims
13. If the tyre is damaged during the mounting phase, do not try to complete the mounting
operation. Remove it and take it away from the service area, marking it as damaged.
14. Inflate the tyres slowly, in steps, while checking the pressure, the tyre, the rim and
the bead. NEVER exceed the pressure limits indicated by the manufacturer.
15. The internal parts in this machine could create contacts or sparks if exposed to flam-
mable vapours (petrol, paint thinner, solvents, etc.). Do not install the machine in a
narrow area or below floor level.
16. Do not operate the machine while under the influence of alcohol, medicine or drugs.
If you are taking prescription or non-prescription medicine, contact a physician to
understand the side effects that the medicine could have on the ability to operate
the machine safely.
17. Always use OSHA, CE approved and authorised personal protective equipment (PPE)
or equipment with equivalent certification while operating the
machine. Consult your supervisor for additional instructions.
18. Remove jewelry, watches, loose clothing, ties and restrain long hair
before using machine.
19. Wear protective, non-slip footwear while using the tyre changer.
20. Wear proper back support and employ proper lifting technique
when placing, moving, lifting or removing wheels from the tire
changer.
21. Only suitably trained personnel can use, service and repair the
machine. Repairs may only be performed by qualified personnel.
Corghi technical personnel are the most qualified individuals.
Employers must determine if an employee is qualified to carry out
any machine repair safely if the operator has attempted to make
the repair.

86 Artiglio 5000 Operator Manual
22. The operator must pay close attention to the warnings on the equipment labels before
starting the machine.
23. Clamp the rim on the wheel support plate during inflation.
1.2.b. DECAL PLACEMENT
No. Code Label Description
1 446429 LABEL,INPUTPRESSUREMAX.
16 BAR
2 446429 LABEL, ATTENTION TANK
PRESSURISED
3 418135 LABEL, ROTATION DIRECTION
4 446665 LABEL, UNCLAMP CONTROL
LABEL
5 -
42015 - Correggio (RE) Italy
ISO9001
Code
Serial N.
X-XXXXXXXX/XX - XX
XXXXXXXXX
QUAL. SYS. CERTIFIED
ANNO DI COSTRUZIONE /
MANUFACTURED
Mod.
V
A
kW
Hz
Ph
bar7psi
Port.max
LABEL, MODEL SERIAL NUM-
BER
6 4-105844 INVERTER MOTOR
7 4-103881 CORGHI
8 4-122534 ARTIGLIO 5000
9 4-122231
CORGHI TOUCHLESS TECH-
NOLOGY
ADHESIVE LABEL
10 4-104346 LIFTER UP-DOWN PED. (OP-
TIONAL)

Artiglio 5000 Operator Manual 87
EN
No. Code Label Description
11 461932 TURNTABLE ROTATION
12 461933 INFLATION PED.
13 446436 DEFLATIONPRESSUREGAUGE
14 461936
PROHIBITION OF TWO OPERA-
TORS WORKING SIMULTANE-
OUSLY
15 346855 ADHESIVE SAFETY STRIP Y/B
50X130
16 462081 RISK OF CRUSHING
17 461930 RISK OF CRUSHING
18 462080 NOISE PROTECTION LABEL
19
461931 INFLATION WARNING PLATE
462778 USA HAZARD PLATE
20 4-122775 WDK APPROVAL

88 Artiglio 5000 Operator Manual
1
2
4
5
6
7
8
9
10
13
14
15
16
17
18
19
20
16

Artiglio 5000 Operator Manual 89
EN
3
11
12
10
7
7
16
8
9
20
16

90 Artiglio 5000 Operator Manual
DANGER WARNING DECALS
P/N. 462081 Risk of crushing
part n. 461930 Risk of crushing
Part n. 461936. Never stand behind the machine.
Only one operator may operate and use the machine
part n. 446442. Danger - pressurised container
part n. 425211A. Risk of electrocution.
part nr 425083. Earth ground terminal.
1.2.c. ELECTRICAL AND PNEUMATIC CONNECTIONS
The electric hook-up used must be suitably sized:
sFORTHEELECTRICPOWERABSORBEDBYTHEMACHINEINDICATEDONITSDATAPLATE&IGsTHEDISTANCEBETWEENTHEMACHINEANDTHEPOWERSUPPLYHOOKUPPOINTSOTHATVOLT-
age drops under full load do not exceed
4% (10% during start-up) compared with
the rated voltage specified on the data
plate.
- The operator must:
slTAPLUGTHATRESPECTSTHECURRENTREGULA-
TIONSONTOTHEPOWERSUPPLYCABLEsCONNECTTHEMACHINETOITSOWNELECTRICALconnection - A, Fig. 2 - and fit a differential
safety circuit-breaker with 30 mA residual
42015 - Correggio (RE) Italy
ISO9001
Code
Serial N.
X-XXXXXXXX/XX - XX
XXXXXXXXX
QUAL. SYS. CERTIFIED
ANNO DI COSTRUZIONE /
MANUFACTURED
Mod.
V
A
kW
Hz
Ph
bar7psi
Port.max
1

Artiglio 5000 Operator Manual 91
EN
CURRENTsINSTALLPROTECTIONFUSESONTHEPOWERLINEthat are suitably sized in accordance with
the indications provided on the machine
DATAPLATE&IGsCONNECTTHEMACHINETOANINDUSTRIALSOCKETTHEMACHINEMUSTNOTBECON-
nected to domestic sockets.
An effective grounding connection is essential for correct operation of the machine.
CAUTION!
Make sure that the available pressure and performance of the compressed air system
are compatible with what is necessary for correct machine operation - see the section
“Technical data”. For correct machine operation, the compressed air supply line must
provide a pressure range from no less than 8.5 bar to no more than 16 bar and guarantee
an air flow rate greater than the average consumption of the machine, which is equal to
140 Nl/min (see technical data).
For correct equipment operation, the air produced must be suitably treated (not
above 5/4/4 according to ISO 8573-1).
CAUTION!
1.2.d TECHNICAL DATA
- Compatible tyre types: CONVENTIONAL – LOW PROFILE - RUN FLAT - BALOON - BSR
- Wheel dimension range:
sWHEELDIAMETER............................................................................................ from 13” to 28”
sMAXIMUMTYREDIAMETER.............................................................................. 1200 mm (47”)
sMAXIMUMTYREWIDTH.....................................................15” (from wheel mating surface)
- Turntable:
s............................................................................................................. resting side: flanged
sCENTRING..................................................................................................................... on cone
sCLAMPING.................................................................................................................... manual
sDRIVESYSTEM.................................................................................. 2-speed motor-inverter
sROTATIONTORQUE........................................................................................................1200 Nm
2

92 Artiglio 5000 Operator Manual
- rotation speed ......................................................................................................7-18 rpm
- Bead breaking unit:
sTOOL.................................................................................................................................disc
sPOSITIONINGINRELATIONTORIM................................... manual with mechanical clamping
sPENETRATION................................................................................................................guided
s"EADBREAKINGCYLINDERFORCE.................................................................................... 7600N
- Wheel lifter (optional):
sOPERATION..................................................................................... automatic lift/manual tilt
sACTIVATION............................................................................................................ pneumatic
sLIFTINGCAPACITY.............................................................................................................. 85 Kg
- Electrical power:
s0H...............................................................................................230V - 0.75 kW - 50/60 Hz
s0H...............................................................................................110V - 0.75 kW - 50/60 Hz
- Compressed air supply:
sOPERATINGPRESSURE...............................................................................................8 -10 bar
- Weight ........................................................................................................425 kg (with lifter)
- weight of electric/electronic parts............................................................................ 10 kg
- Noise level:
s!WEIGHTEDSOUNDPRESSURELEVEL,P!ATTHEWORKINGPOSITION................< 70 dB (A)
The noise levels indicated correspond to emission levels and do not necessarily represent
safe operating levels. Although there is a relationship between emission levels and exposure
levels,
this cannot be used reliably to establish whether
or not further precautions are necessary. The noise levels to which the operator is exposed to
depend on a number of factors, such as duration of exposure, characteristics of the workplace,
other sources of noise etc. . Permissible noise exposure limits may also vary from country to
country. However, this information will enable machine users to make
a more accurate assessment of hazards and risks.
1.2.e. AIR PRESSURE
The machine is equipped with an internal pressure limiting valve to minimize the risk
of over inflating the tyre.
EXPLOSION HAZARD
Do not exceed the pressure recommended by the
tyre manufacturer. Always match the tyre and rim
dimensions.
Avoid personal injury or death
DANGER

Artiglio 5000 Operator Manual 93
EN
1. Never exceed these pressure limitations:
s4HESUPPLYCIRCUITPRESSUREFROMTHECOMPRESSORIS220 psi (15 bar).
s4HEOPERATINGPRESSUREINDICATEDONTHEREGULATORIS150 psi (10 bar).
s4HETYREINmATIONPRESSUREDISPLAYEDONTHEPRESSUREGAUGEMUSTNEVEREXCEEDTHEpressure indicated by the manufacturer on the sidewall of the tyre itself.
2. Activate the air inflation jets only when inserting the bead.
3. Discharge the air pressure system before disconnecting the power supply or other
pneumatic components. The air is stored in a tank for operating the inflation jets.
4. Activate the air inflation jets only if the rim is correctly clamped on the tyre changer (if
required) and the tyre is completely mounted.
1.3. ADDITIONAL RIM/TYRE INFORMATION
Wheels equipped with pressure sensors and special rims or tyres could require
particular work procedures. Consult the service manuals from the manufacturer
of the wheels and tyres.
CAUTION!
1.4. INTENDED MACHINE USE
Thismachinemustonlybeusedto demountandmountvehicletyresfrom/ontherims,using
the provided tools. Any other use is considered inappropriate and may cause accidents.
The machine is not designed for working with motorcycle wheels.
1.5. PERSONNEL TRAINING
1. Employers are responsible for providing a training program for all employees who work
on the wheels concerning the hazards deriving from maintenance and the safety pro-
cedures to be observed. Service and maintenance refers to mounting and demounting
wheels and all the correlated activities, such as inflation, deflation, installation, removal
and handling.
s%MPLOYERSAREREQUIREDTOMAKESURETHATOPERATORSDONOTWORKONTHEWHEELSUNLESSthey have received suitable training regarding the correct maintenance procedures for
the type of wheel being serviced and the operative safety procedures.
s)NFORMATIONTOBEUSEDFORTHETRAININGPROGRAMINCLUDESASAMINIMUMTHEINFORMA-
tion contained in this manual.

94 Artiglio 5000 Operator Manual
2. Employers are required to make sure that every employee demonstrates and maintains
the ability to work on the wheels safely, including the performance of the following
activities:
s$EMOUNTINGTYRESINCLUDINGDEmATIONs)NSPECTINGANDIDENTIFYINGRIMWHEELCOMPONENTSs4YREMOUNTINGs5SINGANYRESTRAININGDEVICECAGEBARRIEROROTHERINSTALLATIONs(ANDLINGRIMWHEELSs4YREINmATIONs-OVEAWAYFROMTHETYRECHANGERWHILEINmATINGTHETYREANDDONOTLEANFORWARDWHENinspecting the wheel during inflation.
s7HEELINSTALLATIONANDREMOVAL3. Employers must evaluate the ability of their employees to carry out these tasks and
work on the wheels in absolutely safety and must provide additional training as required
to make sure that all employees maintain their skills.
1.6. PRELIMINARY CHECKS
Before starting to work, carefully check that all machine components, particularly rub-
ber or plastic parts, are in place, in good condition and operate correctly. If damage or
excessive wear is found during the inspection phase, replace or repair the component
immediately regardless of the amount of damage or wear.
1.7. DURING USE
If strange or unusual noises are heard, if a component or system is not operating correctly
or if you observe anything unusual, immediately stop using the machine.
s)DENTIFYTHECAUSEANDTAKEANYNECESSARYREMEDIALACTIONs#ONTACTYOURSUPERVISORIFNECESSARYMake sure that all other people are positioned at least 6 metres (20 feet) from the machine.
To stop the machine in an emergency:
sDISCONNECTTHEPOWERSUPPLYPLUGsINTERRUPTTHECOMPRESSEDAIRSUPPLYBYDISCONNECTINGTHESUPPLYPIPE

Artiglio 5000 Operator Manual 95
EN
2. TRANSPORT, STORAGE AND HANDLING
Conditions for transporting the machine
The tyre changer must be transported in its original packaging and stowed in the position
shown on the packaging itself.
- Packaging dimensions:
sWIDTH...............................................................................................................................1150 mm
sDEPTH..............................................................................................................................1950 mm
sHEIGHT..............................................................................................................................2100 mm
- Weight of wooden crate:
s3TANDARDVERSION................................................................................................................520 kg
Machine storage and shipping specifications
Temperature: -25° - +55°C.
Do not stack other goods on top of the packing or damage may result.
CAUTION!
Handling
To move the packing, insert the tines of a fork-lift
truck into the slots on the base of the packing itself
(pallet) (Fig.3).
Before moving the machine, refer to the HOISTING/
HANDLING section.
Keep the original packing in good conditions to be used if the equipment has to be
shipped in the future.
CAUTION!
3