Costway EP25435US User manual

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.
EN FR
USER'S MANUAL/MANUEL DE L'UTILISATEUR
EP25435US
Electric Barbecue Grill / Barbecue Électrique

1. Lid
2. Bowl
3. Cooking Grill
4. Heat Reflector Plate
5. Heating Element
6. Handle (x2)
7. Temperature Control
8. Lid Handle
9. Air Vent
10. Hinge Bracket
11. Connection Part
12. Drip Tray
13. Pillar
14. Base
15. Locking Pin
EN
1) IMPORTANT: Your Electric Barbecue Grill has been shipped with
the components shown below. Check everything carefully before
assembly or use. If any part is missing or damaged, do not use this
product and contact the after-sales service center.
2) PRODUCT DIAGRAM
Electric Barbecue Grill Parts
8
9
1
10
15
6
12
13
3
5
4
7
2
11
14
02

EN
3) SCREWS AND WASHER COMPONENTS
17. Small Screw M5X12 (7 pcs)
18. Medium Screw M6X20 (13 pcs)
19. Long Screw M6X45 (4 pcs)
20. Small Wing Nut M5 (6 pcs)
21. Large Wing Nut M6 (11 pcs)
22. Lock Washer (27 pcs)
23. Flat Washer (27 pcs)
24. Locking Pin M5*123 (1 pcs)
25. Flange Nut (2 pcs)
03

EN
NOTE: Tighten all connections by hand first. Once assembly is
complete, tighten all connections fully.
Unscrew and put aside the four (4) M6X20 medium screws on one
end of the pillar.
Add four (4) flat washers on the end of the pillar, then put the pillar
on the base and screw the base to the pillar using the four (4) M6X20
medium screws previously removed.
Step 1 – Attach Pillar to Base
Hardware: M6X20 Medium Screw – 4pcs
Lock Washer – 4pcs
Flat Washer – 4pcs
Assembly Instructions
13
Step 1
22
Lock Washer (4 pcs)
Flat Washer (4 pcs)
Medium Screw M6 x 20 (4 pcs)
23 18
14
04

EN
Unscrew and put aside the four (4) medium screws M6X20 on the
other end of the pillar. Align the pillar to the bottom of the connection
part, then screw the pillar to the bottom of the connection part using
the four (4) M6X20 screws previously removed.
Step 2 - Connection Part
Hardware: M6X20 Medium Screw – 4pcs
Lock Washer – 4pcs
Flat Washer – 4pcs
13
11
Step 2
22
Lock Washer (4 pcs)
Flat Washer (4 pcs)
23
18
14
Medium Screw M6 x 20 (4 pcs)
05

EN
Place the assembled base on flat ground. Unscrew and put aside the
five (5) large wing nuts M6 on the top connection part. Place the bowl
on the top of the connection part and affix the bowl to the connection
part using the five (5) M6 medium wing nuts previously removed.
Step 3 – Attach the Bowl
Hardware: M6X20 Medium Screw – 5pcs
M6 Large Wing Nut – 5pcs
Lock Washer – 5pcs
Flat Washer – 5pcs
13
11
2
Step 3
22
21
Lock Washer (5 pcs)
Flat Washer (5 pcs)
23
18
14
Medium Screw M6 x 20 (5 pcs)
Large Wing Nut M6 (5 pcs)
06

Unscrew the two (2) M6 large wing nuts from each of the two (2)
handles with four long screws M6 x 45 and put aside. Affix the two
(2) handles to either side of the bowl by using the M6 large wing nuts
previously removed.
Step 4 - Bowl Handles
EN
Hardware: M6 Large Wing Nut – 4pcs
Lock Washer – 4pcs
Flat Washer – 4pcs
Long Screw M6 x 45-4pcs
13
11 12
2
Step 4
22 21
Lock Washer (4 pcs)
symmetry
Flat Washer (4 pcs)
Long Screw M6x45 (4 pcs)
23
19
6
14
Large Wing Nut M6 (4 pcs)
07

EN
Unscrew the two(2) Flange nuts M5 from the the hinge bracket and
put aside. Use two(2) M5X12 small screws and put them through the
holes in the bowl. Affix the hinge bracket to the bowl using the two(2)
Flange nuts M5 previously removed.
Step 5 – Bowl Hinge Bracket
Hardware: M5X12 Small Screw – 2pcs
Flange Nut – 2pcs
Lock Washer – 2pcs
Flat Washer – 2pcs
13
11
12
2
Step 5
22 25 10
17
Lock Washer (2 pcs)
Flange Nut (2 pcs)
Flat Washer (2 pcs)
23
6
14
Small Screw M5x12 (2 pcs)
08

EN
Unscrew the small wing nut on the hinge bracket. Affix the hinge
bracket to the lid using the small wing nut previously removed.
Step 6 – Lid Hinge Bracket
Hardware: M5X12 Small Screw – 2pcs
M5 Small Wing Nut – 2pcs
Lock Washer – 2pcs
Flat Washer – 2pcs
1
Step 6
22
20 10
17
Lock Washer (2 pcs)
Small Wing Nut M5 (2 pcs)
Flat Washer (2 pcs)
23
Small Screw M5x12 (2 pcs)
09

EN
Affix the hinge bracket on the bowl to the hinge bracket on the lid
using the locking pin. Lock them using the M5 small wing nut.
Step 7 – Locking Pin
Hardware: Locking Pin M5*123 – 1pc
M5 Small Wing Nut – 1pc
Lock Washer – 1pc
Flat Washer – 1pc
13
1
2
Step 7
22
20
24
23
6
14
M5 Small Wing Nut (1 pc)
Lock Washer (1 pc)
Locking Pin 5*123 (1 pc)
Flat Washer (1 pc)
10