Courtyard Creations KTS136Y-WM User manual

ASSEMBLY INSTRUCTIONS
ATTENTION: THIS PRODUCT IS NOT FOR COMMERCIAL USE
INTENDED FOR RESIDENTIAL USE ONLY.
KTS136Y-WM
Do not discard any of the packaging until you have checked that you have all the parts and pack of fittings.
Keep children away during assembly. This item contains small parts which can be swallowed by children.
Children should always be under direct adult supervision while using the product.
Retain the assembly instructions for future reference.
Please quote following FQC NO. when contacting service center.
SERVICE CENTER TOLL FREE NO.
TEL: [phone]
FAX: [phone]
COURTYARD CREATIONS INC.
!
!
!
!
STOP DON’T RETURN TO STORE!
PARTS LIST
PART
NO. MATERIAL CODE PART Q’TY
PAGE 1 OF 2
1
2
3
4
5
6
7
9
10
11
12
13
14
15
1
1
1
1
1
2
8
12
2
2
8
2
1
1
FIGURE 1
FRONT LEG
SEAT ASSEMBLY
LEFT LEG
RIGHT LEG
BACK ASSEMBLY
SCREW ST4.2*16
BOLT M6*16
WASHER d6.5*D13*1.0
PLASTIC WASHER
PLASTIC NUT M6*P1.0
BOLT CAP
BOLT CAP M6
HEX.KEY WRENCH 4MM
NUT WRENCH 10&13MM
17C17A1306001Y4
82
BOLT M6*45
17C01A0716071Y4
17FA05040301-Y4
1806603030201
1800C23001
1800337004
1800337001
17KAA0101----Y4
17KAB1101----Y4
6
2
1
Attention:
Make sure that all bolts needed for each step match the corresponding
figure to ensure proper assembly.
Step 1:
Place the seat assembly (#1) onto a non-abrasive surface, such as a
carpet, with the underside facing upwards. Insert the front leg (#2) into
the seat assembly (#1). Fasten them together by using screws (#6).
See Figure 1.
You will need the following tools:
- Phillips Screwdriver (Not Included)
- Hex. Key Wrench (See Part #14)
- Nut Wrench (See Part #15)
17C33A0706001Y4
KTS136Y-CS01
KTS136A-CS02
KTS136Y-CS02
KTS136Y-CS03
KTS136Y-CS04

STOP DON’T RETURN TO STORE!
PAGE 2 OF 2
FIGURE 4 FIGURE 5
FIGURE 2 FIGURE 3
Step 4:
Fasten the back assembly (#5) to the seat assembly (#1) by using
bolts (#8), washers (#9), plastic washers (#10), and plastic nuts (#11).
Make sure that all of the bolts have been tightened completely and
then cover them with bolt caps (#12 and #13). See Figure 4.
#8 BOLT M6*45
45
Step 5:
Rotate the back assembly (#5) as shown in Figure 5.
Cleaning and Maintenance
• Wash frame and fabric parts with mild soap and water, rinse thoroughly, and dry completely. Do not use bleach, acid, or other solvents on the
frame and fabric parts.
• We recommend the use of furniture covers when not in use.
• Please inspect and tighten all bolts or fasteners on a regular basis to ensure proper performance and safety of your lounge.
• In order to prolong the life and beauty of your lounge, we recommend that it be stored in a dry and protected area during off season periods.
Missing A Part?
No Need To Go Back To
TheStore!
The store where you made your purchase
does not stock parts for this item
if you need parts,
whether they are missing or damaged.
Call Toll Free
TEL: [phone]
FAX: [phone]
Call us between 9:00 AM and 4:30 PM
Eastern Time Monday through Friday
PLEASE READ THESE INSTRUCTIONS COMPLETELY BEFORE STARTING ASSEMBLY
PLEASE SEPARATE AND IDENTIFY ALL PARTS, MAKING SURE THAT YOU
HAVE ALL OF THEPARTSLISTED.
SHOULD YOU NOTLOCATE ALL OF THE ABOVE PARTS, PLEASE INSPECTALL
PACKING MATERIAL FOR ANY SMALL PARTSTHAT MAYHAVEBECOME
SEPARATED IN SHIPMENT.
SHOULD YOU EXPERIENCEANY DIFFICULTY DURING ASSEMBLYOR IF ANY
PARTIS MISSING OR DAMAGED,PLEASE CALL THE HELP LINE 1-877-539-7436
BEFORERETURNING THE ITEM TO THE STORE.
PLEASE PROVIDE THEFOLLOWING INFORMATION:
1-MODEL NUMBER OF THEPRODUCT.
2-PARTNUMBER AND MATERIAL CODE OF THE PARTFROM THE PARTS LIST
SHOWN ON ASSEMBLY INSTRUCTIONS.
MOST PROBLEMS CAN BERESOLVED WITHOUT RETURNING THIS PRODUCT
TO THERETAILER.
The store where you made your purchase
does not stock parts for this item
if you need parts,
whether they are missing or damaged.
STOP!
Missing A Part?
No Need To Go Back To
The Store
Call us between 9:00 AM and 4:30 PM
Eastern Time Monday through Friday
Call Toll Free
TEL: [phone]
FAX: [phone]
13 899
10 11
#7 BOLT M6*16
16
#7 BOLT M6*16
16
Step 2:
Place the right leg (#3) onto a non-abrasive surface, such as a carpet,
with the bracket facing upwards. At the rear of the lounge, fasten
both the right leg (#3) and the left leg (#4) to the seat assembly (#1)
by using bolts (#7) and washers (#9). Keep the bolts loose.
See Figure 2.
Step 3 :
At the front of the lounge, fasten both the right leg (#3) and the left leg
(#4) to the seat assembly (#1) by using bolts (#7) and washers (#9).
Keep the bolts loose. See Figure 3.
7
7
9
9
12
12 7
7
9
9
12
12
3
4
1
3
4
1
3
4
5
5
Note:
The labels marked “L” and “R” on the legs (#3 and #4) should coincide
with Figure 2 to ensure proper assembly.
R
L