Courtyard Creations TGS37SW-WM User manual

ASSEMBLY INSTRUCTIONS
ATTENTION: THIS PRODUCT IS NOT FOR COMMERCIAL USE
INTENDED FOR RESIDENTIAL USE ONLY.
TGS37SW-WM
PAGE 1 OF 2 COURTYARD CREATIONS INC.
STOP DON’T RETURN TO STORE!
SERVICE CENTER TOLL FREE NO.
TEL: [phone]
FAX: [phone]
1
4
4
4
4
1
1
48
7
6
5
4
3
2
1
HEX. KEY WRENCH 4MM
WASHER d6.5*D13*1.0
BOLT M6*25
LEG
TABLE TOP
17C17A0403001Y4 17KAA0101----Y4
18000337004
17FA05040301-Y4
17C33A0709001Y4
Q’TYQ’TY PARTPART MATERIAL CODEMATERIAL CODE PART
NO.
PART
NO.
PARTS LIST
SCREW ST4.2*12
BOLT CAP
CENTER CONNECTOR
TGS37SW-CS01
TGS38SW-CS02
62TGS37SWY101
FIGURE 1
4
22
2
2
1
You will need the following tools:
- Phillips Screwdriver (Not included)
- Hex. Key Wrench (See Part #8)
Step 1:
Place the table top (#1) onto a non-abrasive surface,
such as a carpet, with its underside facing upwards.
Insert the legs (#2) into the plastic holders attached on
the underside of the table top (#1) rim. Fasten them
together by using screws (#4). See Figure 1.
Use the correct bolts as indicated. Do not tighten any of the bolts until is completely assembled.
Do not sit or stand on this table.
Do not discard of any of the packaging until you have checked that you have all of the parts and
fittings required.
Keep children away during assembly. This item contains small parts that can be swallowed by
children. Children should always be under direct adult supervision while using this product.
Retain these assembly instructions for future reference.
Quote the following FQC NO. when contacting the service center.
!
!
!
!
!
!

FIGURE 3
FIGURE 2
5
22
2
2
3
7
6
Step 3:
Turn the table to its upright position. See Figure 3.
Step 2:
Fasten the center connector (#3) to the middle of the
legs (#2) by using bolts (#5) and washers (#6). Make
sure that all of the bolts have been tightened completely
and cover them with bolt caps (#7). See Figure 2.
Cleaning and Maintenance
• Wash frame parts with mild soap and water, rinse thoroughly, and dry completely. Do not use bleach, acid, or
other solvents on the frame parts.
• Wash glass with mild soap and water, rinse thoroughly, and dry completely.
• Inspect and tighten all bolts and fasteners on a regular basis to ensure the proper performance and safety of
your table.
• When moving the table, lift. Do not drag this table.
• We recommend the use of furniture covers when not in use.
• In order to prolong the life and beauty of your table, we recommend that it be stored in a dry and secure area
during off season periods.
• Tempered glass has been used for increased strength and safety of your table. However, during windy
conditions the umbrella should be lowered and/or removed.
STOP DON’T RETURN TO STORE!
PAGE 2 OF 2
The store where you made your purchase
does not stock parts for this item.
If you need parts,
whether they are missing or damaged,
STOP!
Missing A Part?
No Need To Go Back To
The Store
Call us between 9:00 AM and 4:30 PM
Eastern Time Monday through Friday
Call Toll Free:
TEL: [phone]
FAX: [phone]
READ THESE INSTRUCTIONS COMPLETELY BEFORE STARTING ASSEMBLY
SEPARATE AND IDENTIFY ALL PARTS, MAKING SURE THAT YOU
HAVE ALL OF THEPARTSLISTED.
IF YOU DO NOTLOCATE ALL OF THE PARTS LISTED, INSPECT THE
PACKING MATERIAL FOR SMALL PARTSTHAT MAYHAVEBECOME
SEPARATED DURING SHIPMENT.
IF YOU EXPERIENCEANY DIFFICULTY DURING ASSEMBLYOR IF ANY
PARTS ARE MISSING OR DAMAGED,CALL THE HELP LINE AT
1-877-539-7436 BEFORERETURNING THIS ITEM TO THE STORE.
PROVIDE THEFOLLOWING INFORMATION WHEN CALLING:
1-MODEL NUMBER OF THEPRODUCT.
2-PARTNUMBER AND MATERIAL CODE OF THE PARTFROM THE PARTS
LIST.
MOST PROBLEMS CAN BERESOLVED WITHOUT RETURNING THIS
PRODUCT TO THERETAILER.