Courtyard Creations XTM011X-WM User manual

35
#5 BOLT M6*35
5
7
9
1
2
3
3
Attention:
Make sure that each bolt needed for all steps matches
the corresponding figure to ensure proper assembly.
Step 1:
Fasten the braces (#3) to the right and left legs (#1 and
#2). Fasten them by using steel washers (#7) and bolts
(#5). See Figure 1.
PAGE 1 OF 2 COURTYARD CREATIONS INC.
Use the correct bolts as indicated. Do not tighten any of the bolts until the ottoman is completely assembled.
Do not discard of any of the packaging until you have checked that you have all of the parts and fittings required.
Keep children away during assembly. This item contains small parts that can be swallowed by children.
Children should always be under direct adult supervision while using this product.
Retain these assembly instructions for future reference.
Quote the following FQC NO. when contacting the service center.
SERVICE CENTER TOLL FREE NO.
TEL: [phone]
FAX: [phone]
ASSEMBLY INSTRUCTIONS
ATTENTION: THIS PRODUCT IS NOT FOR COMMERCIAL USE
INTENDED FOR RESIDENTIAL USE ONLY.
HEX.KEY WRENCH 6MM
BOLT CAP M6
BOLT CAP M6
WASHER d6.5*D13*1.0
STEEL WASHER
BOLT M6*35
FIGURE 1
PARTS LIST
PART
NO. MATERIAL CODE PART Q’TY
1 1
1
1
2
4
6
7
8
9
10
11
4
4
4
4
4
1
XTM011X-CS04-4
XTM011X-CS04-3
62XTM011XQ101
XTM011X-CS02-1
17C02A0712003Y4
17C01A0712002Y4
17XA3309
17FA05040301-Y4
18000337006
18000337002
17KAA0201----Y4
RIGHT LEG
LEFT LEG
BRACE
SEAT ASSEMBLY
BOLT M6*35
2
3
4
5
Note:
The labels marked “L” and “R” on the legs (#1 and #2)
should coincide with Figure 1 to ensure proper assembly.
L
R
!
!
!
!
!
STOP DON’T RETURN TO STORE!
XTM011X-WM

Step 2:
Place the seat assembly (#4) onto a non-abrasive
surface, such as a carpet, with its the underside facing
upwards. Place the leg assembly on top of the seat
assembly (#4). See Figure 2.
Step 3:
Fasten the leg assembly to the seat assembly (#4) by
using bolts (#6) and washers (#8). Make sure that all of
the bolts have been tightened completely and cover
them with bolt caps (#9 and #10). See Figure 3.
Step 4:
Turn the ottoman to its upright position.
See Full Assembly.
Cleaning and Maintenance
• Wash frame parts with mild soap and water,
rinse thoroughly and dry completely. Do not use
bleach, acid, or other solvents on the fabric or frame
parts.
• We recommend the use of furniture covers to protect
your ottomans when not in use.
• Inspect and tighten all bolts and fasteners on a regular
basis to ensure the proper performance and safety
of your ottoman.
• In order to prolong the life and beauty of your ottoman,
we recommend that it be stored in a dry and protected
area during off season periods.
FIGURE 3
FULL ASSEMBLY
#6 BOLT M6*35
35
1
4
2
FIGURE 2
2
1
4
PAGE 2 OF 2
68
10
The store where you made your purchase
does not stock parts for this item.
If you need parts,
whether they are missing or damaged,
STOP!
Missing A Part?
No Need To Go Back To
The Store
Call us between 9:00 AM and 4:30 PM
Eastern Time Monday through Friday
Call Toll Free:
TEL: [phone]
FAX: [phone]
READ THESE INSTRUCTIONS COMPLETELY BEFORE STARTING ASSEMBLY
SEPARATE AND IDENTIFY ALL PARTS, MAKING SURE THAT YOU
HAVE ALL OF THEPARTSLISTED.
IF YOU DO NOTLOCATE ALL OF THE PARTS LISTED, INSPECT THE
PACKING MATERIAL FOR SMALL PARTSTHAT MAYHAVEBECOME
SEPARATED DURING SHIPMENT.
IF YOU EXPERIENCEANY DIFFICULTY DURING ASSEMBLYOR IF ANY
PARTS ARE MISSING OR DAMAGED,CALL THE HELP LINE AT
1-877-539-7436 BEFORERETURNING THIS ITEM TO THE STORE.
PROVIDE THEFOLLOWING INFORMATION WHEN CALLING:
1-MODEL NUMBER OF THEPRODUCT.
2-PARTNUMBER AND MATERIAL CODE OF THE PARTFROM THE PARTS
LIST.
MOST PROBLEMS CAN BERESOLVED WITHOUT RETURNING THIS
PRODUCT TO THERETAILER.
STOP DON’T RETURN TO STORE!