Courtyard Creations RUS487W-WM User manual

ASSEMBLY INSTRUCTIONS
ATTENTION: THIS PRODUCT IS NOT FOR COMMERCIAL USE
INTENDED FOR RESIDENTIAL USE ONLY.
RUS487W-WM
PAGE 1 OF 8 COURTYARD CREATIONS INC.
Use the correct bolts as indicated. Do not tighten any of the bolts until the swing is completely assembled.
Do not discard of any of the packaging until you have checked that you have all of the parts and
fittings required.
Keep children away during assembly. This item contains small parts that can be swallowed by
children. Children should always be under direct adult supervision while using this product.
Retain these assembly instructions for future reference.
Quote the following FQC NO. when contacting the service center.
SERVICE CENTER TOLL FREE NO.
TEL: [phone]
FAX: [phone]
!
!
!
!
!
STOP DON’T RETURN TO STORE!

TOP CROSS BEAM
W/ADJUSTABLE TEETH
REAR UPRIGHT SUPPORT
FRONT UPRIGHT SUPPORT
LATERAL CROSS BRACE
REAR CROSS BRACE
RIGHT SEATARM
LEFT SEATARM
FRONT SUPPORT BRACE
BACK SUPPORT BRACE
SEATASSEMBLY
TABLE TOP
TABLE
BOTTOM FRONT SUPPORT
TABLE BOTTOM BRACE RIGHT
TABLE BOTTOM BRACE LEFT
SWING ARM TUBE
SUSPENSION SPRING
BOLT M6*65
RUS487W-CS09-8
62RUS4060N101
62RUS4060N201
62RTS406KI101
62RUS487WH102
RUS487W-CS01-3
RUS487W-CS01-2
62RUS487WH103
62RUS487WH104
RUS487W-CS11-1
RUS487W-CS20-1
62RUS487WT101
62RUS487WX102
62RUS487WX101
62RUS487WM101
28000221002
17GA20405201-Y3
17C01A0722011Y4
Q'TY
BOLT M6*40
SCREW ST4.2*16
WASHER d6.5*D16*1.2
WASHER d8.5*D17*1.6
PLASTIC WASHER
CANOPY/FRAME
CONNECTOR
PLASTIC SCREW
NUT WRENCH 13&17MM
HEX.KEY WRENCH 6MM
CANOPY
BASKET
17C01A0714003Y4
BOLT M8*20.5
17C01A0854211Y4
17C17A1306001Y4
17FA08060601-Y4
17FA05050401-Y4
18000626024
28000J59001
17KAB1201----Y4
17KAA0201----Y4
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
1
2
2
2
1
1
1
1
1
2
1
4
6
1
1
1
4
4
2
8
1
4
1
30
4
4
2
2
1
1
1
1
PAGE 2 OF 8
A. Read the instructions thoroughly. Acquaint yourself with the inventory of parts and the
accompanying drawings to ensure safe and proper assembly.
B. You will need the following tools:
- Phillips Screwdriver
- Nut Wrench (See Part #37)
- Hex. Key Wrench (See Part #38)
C. Lay out all of the parts on a flat surface and identify them using the table below.
PARTS LIST
18060615180101 1
BOLT M6*16
17C01A0706002Y4
BOLT M6*45
17C01A0716072Y4
2
BOLT M10*115
17C01A0930051Y4
SCREW ST4.2*12
17C17A0403001Y4 2
WASHER d10.5*D21*2.0
17FA09070701-Y4 8
4
STEEL NUT M10*1.5
17D02A050501-Y4
PLASTIC NUT M6*P1.0 10
24
18000C23001
18000337003
18000337002
BOLT CAP M10
BOLT CAP M6
118000337005 BOLT CAP M8
STOP DON’T RETURN TO STORE!
PART
NO. MATERIAL CODE PART Q'TY
PART
NO. MATERIAL CODE PART
LEG CAP
RUS487W-CS18-1
61R487WG00001BA

Step 3:
Fasten the lateral cross braces (#4) to the
upright supports (#2 and #3) by using bolts
(#18), washers (#26), and plastic nuts (#29).
Repeat the same procedure for both sides.
See Fig. A – Step 3.
Step 5:
Insert the leg caps (#16) into all of the base feet.
See Fig. A – Step 5.
PAGE 3 OF 8
Step 1
Step 2
Step 3
Step 4
Step 5
Fig. A
Step 1:
Fasten the front and rear upright supports (#2
and #3) at the top by using bolts (#17), washers
(#25), and steel nuts (#28). Repeat the same
procedure for both sides. Keep the bolts loose.
See Fig. A – Step 1.
Do not tighten the bolts
after step 1, fasten all of
the bolts after step 5.
Step 2:
At both ends, insert the assembled upright
supports (#2 and #3) into the top cross beam
w/adjustable teeth (#1). Tighten all of the nuts
and bolts now. See Fig. A – Step 2.
Step 4:
Fasten the rear cross brace (#5) to the rear
upright supports (#3) by using bolts (#18),
washers (#26), and plastic nuts (#29). Tighten
all of the nuts and bolts. See Fig. A – Step 4.
STOP DON’T RETURN TO STORE!
1734
34
25
25
25
25
17
18
35
26
26 29
18
35
16
16
16
16
26 26 29
2
22
3
23
33
33
3
223
2
4
5
4
3
1
ASSEMBLY (Note: When fastening with nuts
and bolts, always use a washer (#25, #26, or #27)
between the tube and the bolt or the tube and
the nut.)
28
28

PAGE 4 OF 8
Fig. B
Fig. C
Step 7:
Fasten the canopy/frame connectors (#32) to
the adjustable teeth on the top cross beam
w/adjustable teeth (#1) by using a plastic
screws (#33). See Fig. C –Step 1 and Step 2.
STOP DON’T RETURN TO STORE!
Step 6:
Slide the canopy/frame connectors (#32) onto
the canopy (#39). Fasten them together by
using screws (#23). Make sure that the teeth
of the canopy/frame connectors are facing
towards the inside of the frame.
See Fig. B – Step 1 and Step 2. 32
39
39
39
32 32
33
33
23
23
Step 1
Step 2
Step 1
Step 2
1

PAGE 5 OF 8
Step 8:
Insert the seat arms (#6 and #7) into the front
support brace (#8) and back support brace (#9).
See Fig. D – Step 1 and Step 2.
Note:
1. The labels marked “L” and “R” on the seat
arms (#6 and #7) should coincide with
Figure D - Step 1 to ensure proper assembly.
2. Make sure that the holes in the supports, the
arms, and the protective covers align with one
another.
Step 9:
Open both of the seat assemblies (#10) and
attach their backs to the seat arms (#6 and #7)
and support braces (#8 and #9) by using bolts
(#19) and washers (#26). Repeat the same
procedure for both sides. See Fig. D – Step 3.
Step 10:
Place the table top (#11) onto a non-abrasive
surface, such as a carpet, with its underside
facing upwards. Fasten the table bottom front
support (#12) to the table top by using bolt (#20),
washer (#27), and plastic washer (#30).
See Fig. D – Step 4.
Step 11:
Insert the table bottom braces (#13 and #14)
into the table bottom front supports (#12).
Repeat the same procedure for both sides.
See Fig. D – Step 5 and Step 6.
Fig. D
STOP DON’T RETURN TO STORE!
Step 1
Step 3
Step 2
Step 4
Step 5
Step 6
7
7
6
6
8
9
19
35
12
11
13
14
14
12
19
10 10
35
26
26
36
20
27
30
9
8
12
L
L
R
R
Note:
The labels marked “L” and “R” on the table
bottom braces (#13 and #14) should coincide
with Figure D - Step 5 to ensure proper
assembly.

Step 14:
Fasten the swing arm tubes (#15) to the seat
arms (#6 and #7) by using bolts (#22), washers
(#26), and plastic nuts (#29). Repeat the same
procedure for both sides. See Fig. G.
Fig. E
Fig. F
Fig. G
PAGE 6 OF 8
Step 12:
Insert the table bottom braces (#13 and #14)
into the connector tabs located on the front
support brace (#8). Fasten together with screws
(#24). See Fig. E – Step 2.
Fasten the table bottom braces (#13 and #14) to
the back support brace (#9) by using bolts (#21)
and washers (#26). See Fig. E – Step 1.
STOP DON’T RETURN TO STORE!
Step 13:
Place the basket (#40) into the table bottom
front support (#12) and back support brace (#9).
Secure the basket to the table bottom front
support (#12) and back support brace (#9) by
using the velcro straps. See Fig. F.
24
40
15 15
22 26
26
26
26
29
29
22 35
35
12
21
13 14
35
26
Step 1
Step 2
8
9
9
15 15
7
6

31 31
31
Step 15:
Hook the suspension springs (#31) into the top
of both holes of the swing arm tubes (#15).
Repeat the same procedure for both sides.
See Fig. H.
Step 16:
Hang the opposite ends of the suspension
springs (#31) into the holes located on the
angled braces of the top cross beam
w/adjustable teeth (#1). Repeat the same
procedure for both sides. See Fig. I.
To assure stability, double check that all of
the bolts have been completely tightened
and cover them with bolt caps (#34, #35,
and #36).
PAGE 7 OF 8
Fig. H
Fig. I
STOP DON’T RETURN TO STORE!
31 15 15
1515
1
31
31
Special Warnings
1. The user of this swing should always inspect it before each use.
2. It is essential to place this swing on level ground and not less than 6 feet away from any obstruction, such as
fences, garages, houses, overhanging branches, laundry lines, or electrical wires.
3. Check the tightness of all of the nuts and bolts on a regular basis.
4. Make sure that the suspension springs are properly secured before each use.
5. Always remove the canopy in heavy wind conditions; otherwise the swing may tip over and cause damage to
its parts.
6. The manufacturer will not accept responsibility for unauthorized repairs or modifications to the swing or its parts.
7. Oil all of the metal parts that move regularly.
8. Weight limit is 700 lbs.
Cleaning and Maintenance
• Wash frame and fabric parts with mild soap and water, rinse thoroughly, and dry completely. Do not use
bleach, acid, or other solvents on the frame or fabric parts.
• We recommend the use of furniture covers when not in use.
• Inspect and tighten all bolts and fasteners on a regular basis to ensure the proper performance and safety of
your swing.
• In order to prolong the life and beauty of your swing, we recommend that it be stored in a dry and protected area
during off season periods.
Warning:
Make sure that both ends of the suspension
springs (#31) go completely through the holes
in the angled braces on the top cross beam
w/adjustable teeth (#1) and the swing arm
tubes (#15).
1

The store where you made your purchase
does not stock parts for this item.
If you need parts,
whether they are missing or damaged,
STOP!
MissingAPart?
No Need To Go Back To
The Store
Call us between 9:00 AM and 4:30 PM
Eastern Time Monday through Friday
Call Toll Free:
TEL: [phone]
FAX: [phone]
READ THESE INSTRUCTIONS COMPLETELY BEFORE STARTING ASSEMBLY
SEPARATE AND IDENTIFY ALL PARTS, MAKING SURE THAT YOU
HAVE ALL OF THEPARTSLISTED.
IF YOU DO NOTLOCATE ALL OF THE PARTS LISTED, INSPECT THE
PACKING MATERIAL FOR SMALL PARTSTHAT MAYHAVEBECOME
SEPARATED DURING SHIPMENT.
IF YOU EXPERIENCEANYDIFFICULTY DURING ASSEMBLYOR IF ANY
PARTS ARE MISSING OR DAMAGED,CALL THE HELP LINE AT
1-877-539-7436 BEFORERETURNING THIS ITEM TO THESTORE.
PROVIDE THEFOLLOWING INFORMATION WHEN CALLING:
1-MODEL NUMBER OF THEPRODUCT.
2-PARTNUMBER AND MATERIAL CODE OF THE PARTFROM THE PARTS
LIST.
MOST PROBLEMSCAN BERESOLVED WITHOUT RETURNING THIS
PRODUCT TO THERETAILER.
PAGE 8 OF 8
STOP DON’T RETURN TO STORE!