Courtyard Creations KUS200X-WM User manual

PARTS LIST
PART
NO.
1
2
3
4
5
6
1
1
1
1
2
4
14
4
14
1
2
2
1
8
10
9
11
13
14
MATERIAL CODE PART Q’TY PART
NO. MATERIAL CODE PART Q’TY
KUS200X-CS03-1
KUS200X-CS02-1
KUS200X-CS04-4
KUS200X-CS04-3
KUS200X-CS04-M
17C33A0706001Y4
17C33A0716001Y4
17C33A0755001Y4
18000337004
17KAA0101----Y4
61K200XC00001BA
61K200XD00001BA
61K200XJ00001BA
PAGE 1 OF 4
!
!
!
!
!
Use the correct bolts as indicated. Do not tighten any of the bolts until the daybed is completely assembled.
Do not discard of any of the packaging until you have checked that you have all of the parts and fittings
required.
Keep children away during assembly. This item contains small parts that can be swallowed by children.
Children should always be under direct adult supervision while using this product.
Retain these assembly instructions for future reference.
Quote the following FQC NO. when contacting the service center.
SERVICE CENTER TOLL FREE NO.
TEL: [phone]
FAX: [phone]
FIGURE 1 2
1
Attention:
Make sure that each bolt needed for all steps matches
the corresponding figure to ensure proper assembly.
Step 1:
Place the back assembly (#1) onto a non-abrasive
surface, such as a carpet. Insert the back assembly (#1)
into the seat assembly (#2). See Figure 1.
KUS200X-WM
ASSEMBLY INSTRUCTIONS
ATTENTION: THIS PRODUCT IS NOT FOR COMMERCIAL USE
INTENDED FOR RESIDENTIAL USE ONLY.
COURTYARD CREATIONS INC.
RIGHT LEG
LEFT LEG
TOP SUPPORT
BACK ASSEMBLY
SEATASSEMBLY
BOLT M6*65
BOLT M6*16
BOLT M6*45
SEAT CUSHION
CANOPY
PILLOW A
PILLOW B
15
16 61K200XJ50001BA
WASHER d6.5*D13*1.0
SCREW ST4.2x16
BOLT CAP
HEX.KEY WRENCH 4MM
6
4
7
17FA05040301-Y4
17C17A1306001Y4
112
1
2
STOP DON’T RETURN TO STORE!
You will need the following tools:
- Phillips Screwdriver (Not included)
- Hex. Key Wrench (See Part #12)

65
#6 BOLT M6*65
FIGURE 5FIGURE 4
3
4
1
3
4
2
FIGURE 3
Step 2:
At the rear of the seat, fasten the seat assembly (#2)
to the back assembly (#1) by using bolts (#6) and
washers (#10). Keep the bolts loose. See Figure 2.
Step 3:
Fasten both the right leg (#3) and the left leg (#4) to the
seat assembly (#2) by using bolts (#7) and washers
(#10). Keep the bolts loose. See Figure 3.
Step 4:
Fasten the seat assembly (#2) to legs (#3 and #4)
by using bolts (#7) and washers (#10). Keep the bolts
loose. See Figure 4.
Step 5:
Fasten the back assembly (#1) to legs (#3 and #4) by
using bolts (#8) and washers (#10). See Figure 5.
FIGURE 2
3
7
7
10
11
11
4
2
1
2
610
11
Note:
The labels marked “L” and “R” on legs (#3 and #4)
should coincide with Figure 3 to ensure proper assembly.
16
#7 BOLT M6*16
R
L
PAGE 2 OF 4
7
10 11
STOP DON’T RETURN TO STORE!
16
#7 BOLT M6*16
45
#8 BOLT M6*45
10
811
10

Cleaning and Maintenance
• Wash frame and fabric parts with mild soap and water, rinse thoroughly, and dry completely. Do not use bleach,
acid, or other solvents on the frame or fabric parts.
• Cushions and pillows may be washed on the surface only by using mild soap and water or a commercial
foaming upholstery cleaner if necessary. If washed, rinse well and hang to dry. Do not machine wash or dry.
• We recommend the use of furniture covers when not in use.
• Inspect and tighten all bolts and fasteners on a regular basis to ensure the proper performance and safety of
your daybed.
• In order to prolong the life and beauty of your daybed, we recommend that it be stored in a dry and protected
area during off season periods.
Step 6:
Insert the top supports (#5) into legs (#3 and #4) by
using screws (#9). Make sure that all of the bolts have
been tightened completely and cover them with bolt
caps (#11). See Figure 6.
Step 7:
Place the canopy (#13) onto the top supports (#5).
See Figure 7.
Step 8:
Place the seat cushion (#14) and the pillows (#15 and
#16) onto the daybed. Secure the cushion to the
daybed by using the plastic clamps. See Figure 8.
PAGE 3 OF 4
FIGURE 6
FIGURE 8
FIGURE 7
STOP DON’T RETURN TO STORE!
5
55
5
13
3
4
5
9
14
16 16 15 15

The store where you made your purchase
does not stock parts for this item.
If you need parts,
whether they are missing or damaged,
STOP!
MissingAPart?
No Need To Go Back To
The Store
Call us between 9:00 AM and 4:30 PM
Eastern Time Monday through Friday
Call Toll Free:
TEL: [phone]
FAX: [phone]
READ THESE INSTRUCTIONS COMPLETELY BEFORE STARTING ASSEMBLY
SEPARATE AND IDENTIFY ALL PARTS, MAKING SURE THAT YOU
HAVE ALL OF THEPARTSLISTED.
IF YOU DO NOTLOCATE ALL OF THE PARTS LISTED, INSPECT THE
PACKING MATERIAL FOR SMALL PARTSTHAT MAYHAVEBECOME
SEPARATED DURING SHIPMENT.
IF YOU EXPERIENCEANYDIFFICULTYDURING ASSEMBLYOR IF ANY
PARTS ARE MISSING OR DAMAGED,CALL THE HELP LINE AT
1-877-539-7436 BEFORERETURNING THIS ITEM TO THESTORE.
PROVIDE THEFOLLOWING INFORMATION WHEN CALLING:
1-MODEL NUMBER OF THEPRODUCT.
2-PARTNUMBER AND MATERIAL CODE OF THE PARTFROM THE PARTS
LIST.
MOST PROBLEMSCAN BERESOLVED WITHOUT RETURNING THIS
PRODUCT TO THERETAILER.
PAGE 4 OF 4
STOP DON’T RETURN TO STORE!